| Age | Commit message (Collapse) | Author |
|---|
|
genext2fs creates revision level 0 filesystems, which are not readable
by u-boot due to the initialized group descriptor size field.
f798b1dda1c5de818b806189e523d1b75db7e72d
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: FrostyBytes@protonmail.com
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Instead of shuffling bits from two adjacent 16 bit words, use one 16 bit
word with the appropriate byte offset in the buffer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
get_fatent_value(...) flushes changed FAT entries to disk when fetching
the next FAT blocks, in every other aspect it is identical to
get_fatent(...).
Provide a stub implementation for flush_dirty_fat_buffer if
CONFIG_FAT_WRITE is not set. Calling flush_dirty_fat_buffer during read
only operation is fine as it checks if any buffers needs flushing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
|
|
The FAT is read/flushed in segments of 6 (FATBUFBLOCKS) disk sectors. The
last segment may be less than 6 sectors, cap the length.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
|
|
The u-boot command fatwrite empties FAT clusters from the beginning
till the end of the file.
Specifically for FAT12 it fails to detect the end of the file and goes
beyond the file bounds thus corrupting the file system.
Additionally, FAT entry chaining-up into a file is not implemented
for FAT12.
The users normally workaround this by re-formatting the partition as
FAT16/FAT32, like here:
https://github.com/FEDEVEL/openrex-uboot-v2015.10/issues/1
The patch fixes the bounds of a file and FAT12 entries chaining into
a file, including EOF markup.
Signed-off-by: Philipp Skadorov <philipp.skadorov@savoirfairelinux.com>
|
|
Now that we free resources in sandbox_fs_ls Coverity is letting us know
that in some cases we might leak. So in case of error we should still
let os_dirent_free free anything that was allocated.
Fixes: 86167089b71c ("sandbox/fs: Free memory allocated by os_dirent_ls")
Reported-by: Coverity (CID: 153450)
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
fill_dir_slot use get_contents_vfatname_block as a temporary buffer for
constructing a list of dir_slot entries. To save the memory and providing
correct type of memory for above usage, a local buffer with accurate size
declaration is introduced.
The local array size 640 is used because for long file name entry,
each entry use 32 bytes, one entry can store up to 13 characters.
The maximum number of entry possible is 20. So, total size is
32*20=640bytes.
Signed-off-by: Genevieve Chan <ccheauya@altera.com>
Signed-off-by: Tien Fong Chee <tfchee@altera.com>
|
|
Support was already implemented, but not hooked up. This fixes several
fails in the test cases.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
A sparse file may have regions not mapped by any extents, at the start
or at the end of the file, or anywhere between, thus not finding a
matching extent region is never an error.
Found by python filesystem tests.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Instead of creating a journal entry for each directory block, even
if the block is unmodified, only log the modified block.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
The direntlen checks were quite bogus, i.e. the loop termination used
"len + offset == blocksize" (exact match only), and checked for a
direntlen less than 0. The latter can never happen as the len is
unsigned, this has been reported by Coverity, CID 153384.
Use the same code as in search_dir for directory traversal. This code
has the correct checks for direntlen >= sizeof(struct dirent), and
offset < blocksize.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reported-by: Coverity (CID: 153383, 153384)
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Use the same variable names as in search_dir, to make purpose of variables
more obvious.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We are supposed to use #include <...> to include headers in the
public include paths. We should use #include "..." only for headers
in local directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable mounting of ext4 fs with 64bit feature, as it is supported now.
These had been disabled in 6f94ab6656ceffb3f2a972c8de4c554502b6f2b7.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
Also adjust high 16/32 bits when free inode/block counts are modified.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
The descriptor size is variable, thus array indices are not generically
applicable. The larger group descriptors also contain e.g. high parts
of block numbers, which have to be read and written.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
The correct descriptor size must be used when calculating offsets, and
also to read the correct amount of data.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
The helper functions encapsulate access of the block group descriptors,
independent of group descriptor size. The helpers also deal with the
endianess of the fields, and with split fields like free_blocks/
free_blocks_high.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
If EXT4_FEATURE_INCOMPAT_64BIT is set, the descriptor can be read from
the superblocks, otherwise it defaults to 32.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
If the same block is updated multiple times in a row during a single
file system operation, gd_index is decremented to use the same journal
entry again. Avoid loosing the already allocated buffer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
read_allocated block may return block number 0, which is just an indicator
a chunk of the file is not backed by a block, i.e. it is sparse.
During file deletions, just continue with the next logical block, for other
operations treat blocknumber <= 0 as an error.
For writes, blocknumber 0 should never happen, as U-Boot always allocates
blocks for the whole file. Reading already handles this correctly, i.e. the
read buffer is 0-fillled.
Not treating block 0 as sparse block leads to FS corruption, e.g.
./sandbox/u-boot -c 'host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
ext4write host 0 0 /2.5GB.file 1 '
The 2.5GB.file from the fs test is actually a sparse file.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
The data blocks are identical for files using traditional direct/indirect
block allocation scheme and extent trees, thus this code part can be
common. Only the code to deallocate the indirect blocks to record the
used blocks has to be seperate, respectively the code to release extent
tree index blocks.
Actually the code to release the extent tree index blocks is still missing,
but at least add a FIXME at the appropriate place.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
|
|
Make sure the the extra_isize field (offset 128) is initialized to 0, to
mark any extra data as invalid.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
fs->inodesz is already correctly (i.e. dependent on fs revision)
initialized in ext4fs_mount.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
temp_ptr should always be freed, even if the function is left via
goto fail.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
If the blocksize is 1024, count is initialized with 1. Incrementing count
by 8 will never match (count == fs->blksz * 8), and ptr may be
incremented beyond the buffer end if the bitmap is filled. Add the
startblock offset after the loop.
Remove the second loop, as only the first iteration will be done.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
The last free block of a block group may be in its middle. After it has
been allocated, the next block group should be scanned from its beginning.
The following command triggers the bad behaviour (on a blocksize 1024 fs):
./sandbox/u-boot -c 'i=0; host bind 0 ./disk.raw ;
while test $i -lt 260 ; do echo $i; setexpr i $i + 1;
ext4write host 0:2 0 /X${i} 0x1450; done ;
ext4write host 0:2 0 /X240 0x2000 ; '
When 'X240' is extended from 5200 byte to 8192 byte, the new blocks should
start from the first free block (8811), but it uses the blocks 8098-8103
and 16296-16297 -- 8103 + 1 + 8192 = 16296. This can be shown with
debugfs, commands 'ffb' and 'stat X240'.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
zero_buffer is never written, thus clearing it is pointless.
journal_buffer is completely initialized by ext4fs_devread (or in case
of failure, not used).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
e2fsck warns about "Group descriptor 0 marked uninitialized without
feature set."
The bg_itable_unused field is only defined if FEATURE_RO_COMPAT_GDT_CSUM
is set, and should be set (kept) zero otherwise.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Scanning only the direct blocks of the directory file may falsely report
an existing file as nonexisting, and worse can also lead to creation
of a duplicate entry on file creation.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
While directories can be read using the old linear scan method, adding a
new file would require updating the index tree (alternatively, the whole
tree could be removed).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Previously, only the last directory block was scanned for available space.
Instead, scan all blocks back to front, and if no sufficient space is
found, eventually append a new block.
Blocks are only appended if the directory does not use extents or the new
block would require insertion of indirect blocks, as the old code does.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
The following command crashes u-boot:
./sandbox/u-boot -c 'i=0; host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
while test $i -lt 200 ; do echo $i; setexpr i $i + 1;
ext4write host 0 0 /foobar${i} 0; done'
Previously, the code updated the direct_block even for extents, and
fortunately crashed before pushing garbage to the disk.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
In case the dir entry creation failed, ext4fs_write would later overwrite
a random inode, as inodeno was never initialized.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
The following command triggers a segfault in search_dir:
./sandbox/u-boot -c 'host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
ext4write host 0 0 /./foo 0x10'
The following command triggers a segfault in check_filename:
./sandbox/u-boot -c 'host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
ext4write host 0 0 /. 0x10'
"." is the first entry in the directory, thus previous_dir is NULL. The
whole previous_dir block in search_dir seems to be a bad copy from
check_filename(...). As the changed data is not written to disk, the
statement is mostly harmless, save the possible NULL-ptr reference.
Typically a file is unlinked by extending the direntlen of the previous
entry. If the entry is the first entry in the directory block, it is
invalidated by setting inode=0.
The inode==0 case is hard to trigger without crafted filesystems. It only
hits if the first entry in a directory block is deleted and later a lookup
for the entry (by name) is done.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
le32_to_cpu() must only convert the revision_level and not the boolean
result.
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
All fields were accessed directly instead of using the proper byte swap
functions. Thus, ext4 write support was only usable on little-endian
architectures. Fix this.
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
Instead of __{be,le}{16,32}_to_cpu use {be,le}{16,32}_to_cpu.
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
Change all the types of ext2/4 fields to little endian types and all the
JBD fields to big endian types. Now we can use sparse (make C=1) to check
for statements where we need byteswaps.
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
Current description does not match the function behaviour.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
The code caches 6 sectors of the FAT. On FAT traversal, the old contents
needs to be flushed to disk, but only if any FAT entries had been modified.
Explicitly flag the buffer on modification.
Currently, creating a new file traverses the whole FAT up to the first
free cluster and rewrites the on-disk blocks.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
fatlength is a local variable which is no more used after the assignment.
s_name is not used in the function, save the strncpy.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
|
|
This fixes incorrect filenames in cbfsls output.
Signed-off-by: Yaroslav K. <yar444@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[clean up checkpatch errors and warnings]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
With e2fsprogs after 1.43 the 64bit and metadata_csum features are
enabled by default. The metadata_csum feature changes how
ext4_group_desc->bg_checksum is calculated, which would break write
support. The 64bit feature however introduces changes such that it
cannot be read by implementations that do not support it. Since we do
not support this, we must not mount it.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reported-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Fix the following build errors when building sandbox on x86 32-bit:
In file included from fs/cbfs/cbfs.c:8:0:
include/malloc.h:364:7: error: conflicting types for 'memset'
void* memset(void*, int, size_t);
^
In file included from include/compiler.h:123:0,
from include/cbfs.h:10,
from fs/cbfs/cbfs.c:7:
include/linux/string.h:78:15: note: previous declaration of 'memset' was here
extern void * memset(void *,int,__kernel_size_t);
^
In file included from fs/cbfs/cbfs.c:8:0:
include/malloc.h:365:7: error: conflicting types for 'memcpy'
void* memcpy(void*, const void*, size_t);
^
In file included from include/compiler.h:123:0,
from include/cbfs.h:10,
from fs/cbfs/cbfs.c:7:
include/linux/string.h:81:15: note: previous declaration of 'memcpy' was here
extern void * memcpy(void *,const void *,__kernel_size_t);
^
scripts/Makefile.build:280: recipe for target 'fs/cbfs/cbfs.o' failed
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
|
