| Age | Commit message (Collapse) | Author |
|---|
|
Some CPUs like PPC, BLACKFIN need sync() to ensure cfi flash write command
is fully finished. The sync() is defined in each CPU's io.h file. For
those CPUs which do not need sync for now, a dummy sync() is defined in
their io.h as well.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
|
|
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Also display enabled/disabled RAID 6 support for 440SP/440SPe PPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
MPC8360EMDS
This patch also adds an improved I2C set_speed(), which handles all clock
frequencies.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
|
|
Add support for the Freescale MPC8360EMDS board.
Includes DDR, DUART, Local Bus, PCI.
|
|
common QE immap file. Also required for 8360.
|
|
Mainly add QE device dependencies, with appropriate 8360 protection.
Lindent also run.
|
|
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Hello,
Attached is a patch implementing multiple I2C buses on the MPC834x CPU
family and the MPC8349EMDS board in particular.
This patch requires Patch 1 (Add support for multiple I2C buses).
Testing was performed on a 533MHz board.
/*** Note: This patch replaces ticket DNX#2006083042000027 ***/
Signed-off-by: Ben Warren <bwarren@qstreams.com>
CHANGELOG:
Implemented driver-level code to support two I2C buses on the
MPC834x CPU family and the MPC8349EMDS board. Available I2C bus speeds
are 50kHz, 100kHz and 400kHz on each bus.
regards,
Ben
|
|
Incorporated the common unified variable names and the changes in preparation
for releasing mpc8360 patches.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Replace private IMMAP I2C structures with generic reg block
and allow 86xx to have multiple I2C device busses.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
in an effort to begin to unify the umpteen FSL I2C drivers that
are all otherwise very similar.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Removed spurious LAWAR thing.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
Conflicts:
board/stxxtc/Makefile
|
|
|
|
Both 8641 and 8641D have SVR == 0x8090, and are distinguished
by the byte in bits 16-23 instead.
Thanks to Jason Jin for noticing.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
|
|
|
|
|
|
|
|
|
|
Conflicts:
include/ft_build.h
include/pci.h
Resolved, though.
|
|
Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
|
|
|
|
|
|
Patch by John Otken, 08 May 2006
|
|
|
|
|
|
- Removed MPC8349ADS port
- Added PCI support to MPC8349ADS
- reworked memory map to allow mapping of all regions with BATs
Patch by Kumar Gala 20 Apr 2006
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
|
|
|
|
Patch by Murray Jensen, 08 Jul 2005
|
|
|
