| Age | Commit message (Collapse) | Author |
|---|
|
Remove MK_STR from places that consume CONFIG_ROOTPATH to force all definitions to be string literals.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8],
software need to read the SW1 status to decide what the sysclk needs.
SW1[8~6] : frequency
0 0 1 : 83.3MHz
0 1 0 : 100MHz
others: 66.667MHz
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.
The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.
CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.
CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.
Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.
README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
