summaryrefslogtreecommitdiff
path: root/include/configs/am335x_evm.h
AgeCommit message (Collapse)Author
2018-08-03Add Beaglebone Enhanced supportKoen Kooi
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black, but with the following differences: * Gigabit capable PHY * Extra USB hub, optional i2c control * lps3331ap barometer connected over i2c * MPU6050 6 axis MEMS accelerometer/gyro connected over i2c * 1GiB DDR3 RAM * RTL8723 Wifi/Bluetooth connected over USB Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-11spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
2018-04-08Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-04-08ti: am335x: Fix bootargs when building without NETAlex Kiernan
If DHCP/PXE commands are disabled then the compilation fails due to bootargs attempting to use them: include/config_distro_bootcmd.h:319:2: error: expected ‘}’ before ‘BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE’ Ensure that if the command aren't enabled, we don't try and use them. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-06Add support for BeagleBoard.org PocketBeagleJason Kridner
Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x 55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more. https://beagleboard.org/pocket This was tested using the am335x_evm_usbspl_defconfig. Note that MII pins are enabled despite not having Ethernet on this board. This avoids an issue where otherwise many timeout errors would be generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976 for some related discussion. Signed-off-by: Jason Kridner <jdk@ti.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-05spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the ↵Faiz Abbas
U-boot CONFIG Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER. This enables users to block text using CONFIG_IS_ENABLED() instead of resorting to #if ladders with SPL and non-SPL cases. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-02-24Convert CONFIG_BOOTCOUNT_AM33XX to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_AM33XX Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-15Convert CONFIG_BOOTCOUNT_LIMIT to KconfigLukasz Majewski
This converts the following to Kconfig: CONFIG_BOOTCOUNT_LIMIT Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2018-02-14am335x_evm: Consolidate eMMC partitions with DFU infoSam Protsenko
>From DFU_ALT_INFO_EMMC (include/environment/ti/dfu.h) we can see that rootfs will be flashed to second partition on eMMC. But at the moment we have only one partition in $partitions environment variable. Let's add "bootloader" partition prior to "rootfs", so that DFU works correctly. This also fixes eMMC boot, which looks for rootfs on second partition. "bootloader" partition start corresponds to "u-boot.img.raw" in DFU eMMC info, which is 0x300 sector (384 KiB offset from eMMC start). rootfs start address can be also found from DFU eMMC info. bootloader-related area is finished at 0x1500 sector (2688 KiB offset from eMMC start). This should be the start address for rootfs in $partitions environment variable. While at it, fix U-Boot environment address to be the same as for AM57x EVM, so that it doesn't clash with other partitions. So now eMMC layout looks like this: =============================================================== 0 +------------------------+ | MBR/GPT header | 128 - 128 +------------------------+ | MLO | 256 - 384 +------------------------+ | u-boot.img | 1792 bootloader 2176 +------------------------+ | //////// hole //////// | 256 - 2432 +------------------------+ | U-Boot environment | 128 - 2560 +------------------------+ | U-Boot environment | 128 - | (redundant) | 2688 +------------------------+ | rootfs | remaining rootfs end +------------------------+ =============================================================== "hole" area can be used further for storing U-Boot environment (like it's done in AM57x EVM config file) or for increasing u-boot.img area (in case u-boot.img size increased, e.g. if new dtbs were added). This commit conforms with Linux partition table from f6d245b8c56c ("arm: am57xx: Fix Linux boot from eMMC") commit, making things in uniform way. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-22Convert CONFIG_USB_MUSB_OMAP2PLUS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_USB_MUSB_OMAP2PLUS CONFIG_USB_MUSB_AM35X CONFIG_USB_MUSB_DSPS CONFIG_USB_MUSB_PIO_ONLY Signed-off-by: Adam Ford <aford173@gmail.com>
2017-12-18am335x_evm: Fix DFU for eMMCSam Protsenko
Use dfu_alt_info_emmc variable from include/environment/ti/dfu.h file. It was probably overlooked when extracting DFU variables to mentioned file. This patch fixes DFU on BeagleBone Black, so that we can use commands like ones below to upgrade various images on eMMC: => setenv dfu_alt_info $dfu_alt_info_emmc => dfu 0 mmc 1 $ dfu-util -D MLO -a MLO.raw $ dfu-util -D u-boot.img -a u-boot.img.raw Without this patch, the user is forced to assign the value to dfu_alt_info_emmc manually, which contradicts with instructions [1]. [1] http://processors.wiki.ti.com/index.php/Linux_Core_U-Boot_User%27s_Guide Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-11-17Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMANDTom Rini
We first introduce CONFIG_USE_BOOTCOMMAND, similar to CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex scheme around this usage, and these have been defered for the moment so that platform maintainers can work on a migration plan. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-11-05Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_NAND_MXC CONFIG_NAND_OMAP_GPMC CONFIG_NAND_OMAP_GPMC_PREFETCH CONFIG_NAND_OMAP_ELM CONFIG_SPL_NAND_AM33XX_BCH CONFIG_SPL_NAND_SIMPLE CONFIG_SYS_NAND_BUSWIDTH_16BIT Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> [trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues, add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-03usb: gadget: usb_ether: Move the interfaces to KconfigMaxime Ripard
We need to select an interface for the usb_ether gadget, and they haven't been converted to Kconfig yet. Add a choice to make sure we have an option selected, and convert all the users. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03usb: gadget: Convert USB_ETHER to KconfigMaxime Ripard
The USB Ethernet gadget option has not yet been moved to Kconfig, let's deal with that. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03usb: gadget: Move USBNET_HOST_ADDR to KconfigMaxime Ripard
While the USB Ethernet device address is already defined in Kconfig, the host address isn't. Convert it. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-09-01Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigsTom Rini
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's not strictly part of fastboot. - Add some defaults for the fastboot buffer location and size - Migrate all options listed in cmd/fastboot/Kconfig - Cleanup the README Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-17dm: mmc: Drop CONFIG_DM_MMC_OPSSimon Glass
All boards which use DM_MMC have now been converted to use DM_MMC_OPS. Drop the option and good riddance. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-13spl: moveconfig: remove SPL_LDSCRIPT definitions for header-filesPhilipp Tomsich
With the hierarchical defaults set up, we remove these from the header files. To do so, I've run moveconfig on SPL_LDSCRIPT and this commits the changes. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-11Convert CONFIG_CMD_SPL_WRITE_SIZE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_SPL_WRITE_SIZE Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11Convert CONFIG_CMD_SPL_NAND_OFS to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_SPL_NAND_OFS Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-08configs: Finish migration of PHY_GIGETom Rini
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-31env: Migrate CONFIG_ENV_IS_IN_FAT options to KconfigTom Rini
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that they can be modified via Kconfig. Migrate all existing users to the new values. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25Convert CONFIG_ENV_IS_IN_FAT to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_FAT Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25Convert CONFIG_ENV_IS_IN_SPI_FLASH to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_SPI_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25Convert CONFIG_ENV_IS_IN_FLASH to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-24configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFSTom Rini
The above CONFIG options are in Kconfig, and now have correct depends and inter-dependencies. Migrate these to configs/ from include/configs/. In the case of CMD_UBIFS also change it to be a default y if CMD_UBI. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-11configs: am335x_evm: Enable FASTBOOT based on kconfigAlexandru Gagniuc
When CONFIG_CMD_FASTBOOT or CONFIG_USB_FUNCTION_FASTBOOT are defined in am335x_evm.h, a dependency on g_dnl.c is created. This in turn creates a dependency on having USB gadget enabled. As a result we can't create configs with USB gadget disabled. Since these CONFIG_ variables are now part of kconfig, move them to the board defconfigs, and out of am335x_evm.h. This both preserves current defaults, and allows creating configs with USB gadget off. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22Convert CONFIG_CMD_EEPROM et al to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_EEPROM_LAYOUT_HELP_STRING Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Rework Kconfig logic slightly, define EEPROM location on TI eval platforms] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15include: config: am335x: disable DM_MMC_OPS if DM_MMC is disabledJean-Jacques Hiblot
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-11configs: am335x_evm: Enable SPL_DMLokesh Vutla
Enable SPL_DM on all AM335x based TI platforms. http://patchwork.ozlabs.org/patch/751300/ Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-11configs: am335x_evm: Use omap2 generic spl load scriptLokesh Vutla
No reason to use a separate load script for am33xx than using omap-common load script. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08ARM: ti: consolidate mmc environment variablesSekhar Nori
Introduce include/environment/ti/mmc.h that consolidates environment variable definitions for various TI boards that support MMC/SD. This allows reuse of same environment variables on non-ARMv7 TI platforms like OMAP-L138 for example. While at it, move DFU-related environment variable includes to only non-SPL builds for AM335x and AM437x since they are not really used for SPL today. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08config: am335x_evm: detect BeagleBone Blue using BLArobertcnelson@gmail.com
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing on robotics with a TI wl1835 wireless module for connectivity. This board can be indentified by the BLAx value after A335BNLT (BBB) in the at24 eeprom: BLAx: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|] http://beagleboard.org/blue https://github.com/beagleboard/beaglebone-blue firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08config: am335x_evm: detect Green Wireless using GW1robertcnelson@gmail.com
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the GW1x value after A335BNLT (BBB) in the at24 eeprom: GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|] http://beagleboard.org/green-wireless http://wiki.seeed.cc/BeagleBone_Green_Wireless/ firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: Stored in at24 eeprom at address 5-16: hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08config: am335x_evm: detect Black Wireless using BWArobertcnelson@gmail.com
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom: BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|] http://beagleboard.org/black-wireless https://github.com/beagleboard/beaglebone-black-wireless firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-19Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich
Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-12flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-28arm: Clean up MACH_TYPE_xxx usage after re-sync of mach-typesTom Rini
With the latest mach-types values we have many instances where we no longer need to define a value and a few cases where the name (but not value) have changed slightly. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPTPatrick Delaunay
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28disk: convert CONFIG_EFI_PARTITION to KconfigPatrick Delaunay
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-25Convert CONFIG_ARCH_MISC_INIT to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ARCH_MISC_INIT Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-21config: Move CONFIG_BOARD_LATE_INIT to defconfigsJagan Teki
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-14ti: am335x: mmc: Set CONFIG_SYS_MMC_MAX_DEVICEEmmanuel Vadot
Set CONFIG_SYS_MMC_MAX_DEVICE to 2 for am335x SoC. This define is needed in the API code. Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
2017-01-09am335x_evm: enable usb ether gadget as it supports DM_ETHMugunthan V N
Since usb ether gadget have support for driver model, so enable usb ether gadget. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03Merge branch 'master' of git://www.denx.de/git/u-boot-dmTom Rini
generated by cgit (git 2.34.1) at 2024-12-28 16:05:05 +0000