| Age | Commit message (Collapse) | Author |
|---|
|
Adds code to detect AM43xx HS EVMS - the string in the
I2C EEPROM for HS EVMs differs from GP EVMs. Adds code to
for evm detection, regardless of whether the evm is for
GP or HS parts, and updates board init to use that.
Modifies findfdt command to pick up am437x-gp-evm.dtb for
the HS EVMs also, as the boards are similar except for
some security specific changes around power supply and
enclosure protection.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Updates configs/am43xx_evm.h to use CONFIG options from
SOC specific Kconfig file for various calculations.
On AM43x devices, the address of SPL entry point depends on
the device type, i.e. whether it is secure or non-secure.
Further, for non-secure devices, the SPL entry point is different
between USB HOST boot mode, other "memory" boot modes (MMC, NAND)
and "peripheral" boot modes (UART, USB)
To add to the complexity, on secure devices, in addition to the
above differences, the SPL entry point can change because of the
space occupied by other components (other than u-boot or spl)
that go into a secure boot image.
To prevent the user from having to modify source files every time
any component of the secure image changes, the value of
CONFIG_SPL_TEXT_BASE has been set using a Kconfig option that
is supplied in the am43xx_*_defconfig files
Using the CONFIG options also enables us to do away with some
compile time flags that were used to specify CONFIG_SPL_TEXT_BASE
for different boot modes.
On QSPI devices, the same problem described above occurs w.r.t. the
address of the u-boot entry point in flash, when booting secure
devices. To handle this, CONFIG_SYS_TEXT_BASE is also setup via
a Kconfig option and the defconfig files.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.
This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.
Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
And also reformat defconfigs using "make savedefconfig" rule.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Description was borrowed from kernel dwc3 Kconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED
While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.
Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.
Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Support for loading bootscript and text env file is duplicated in all TI
platforms. Add this information to DEFAULT_MMC_TI_ARGS so that it can be
reused in all TI platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
With commit aee119bd70b8 ('am43xx_evm: add usb host boot support') usb
commands is removed from U-boot second stage and enbaled only on USB
boot config. Fixing this by enable USB commands for both USB boot and
in second stage u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_SF_DEFAULT_MODE is used to select default SPI mode when using
sf commands. Therefore fix am43xx to use CONFIG_SF_DEFAULT_MODE instead
of CONFIG_DEFAULT_SPI_MODE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Since OMAP's spl doesn't support DM currently, do not define
DM_SPI and DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This option only complicates the code unnecessarily, just use
CONFIG_SYS_DEF_EEPROM_ADDR as the default address if there are
only five arguments to eeprom {read/write} if this is defined.
If CONFIG_SYS_DEF_EEPROM_ADDR is not defined, we mandate all
six arguments.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
This adds support to update firmware on qspi flash present on
am437x-sk-evm and am43xx-epos-evm via DFU.
On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0
On host:
$ sudo dfu-util -l
$ sudo dfu-util -D u-boot.bin -a u-boot.bin
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
Since spl doesn't support DM currently, do not define DM_MMC
for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
Tested on am437x gp evm and am437x sk evm
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
When AM437x EVM is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.
The default 4 second limit times-out more often than not. This is
observed when testing with a D-Link DGS-1008A desktop switch.
Increase the auto-negotiation time-out for AM437x EVM to handle
this case.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Define default mmc args in ti_armv7_common.h so that all
TI platforms can reuse.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The usbboot environment variable has 'usb start' command but
doesn't have the corresponding 'usb stop' command. This breaks
usb peripheral mode if tried after 'run usbboot' fails to load
the images in usb host mode.
Fix it here by adding 'usb stop' command in usbboot env.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.
Many of the options are architecture specific, however a lot are common
with v7 architecture. So, step 1 will be to move out OMAP specific stuff
from ti_armv7_common into a ti_armv7_omap.h header which is then used
by all the relevant architecture headers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
|
|
Remove all redundant dwc3 driver function calls that
are defined by dwc3 driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
This commit moves:
- CONFIG_SPI_FLASH_BAR
from include/configs/*.h into configs/*_defconfigs
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
|
|
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Across several devices network environment variables are duplicated.
Move these variables to a common include file which insures the environment
variables are reused and insures devices across product lines share the same
values.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
AM43xx Industrial Development Kit is a new board
based on AM437x line of SoCs. Targetted at Industrial
Automation applications, it comes with EtherCAT, motor
control and other goodies.
Thanks to James Doublesin for all the help.
Cc: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes
And remove it from headers that end up redefining it.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
without having to modify the configuration header.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
