summaryrefslogtreecommitdiff
path: root/include/configs/cm_fx6.h
AgeCommit message (Collapse)Author
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-25mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTDFrieder Schrempf
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in SPL. They often rely on hacks in the board header files to include this option conditionally. To be able to fix this, we previously introduced a separate option SPL_SPI_FLASH_MTD. Therefore we can now adjust the Makefile and change the code in sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD). We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the header files to the according defconfigs. The affected boards are socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6 and da850evm. We do this all in one patch to guarantee bisectibility. This change was tested with buildman to make sure it does not introduce any regressions by comparing the resulting binary sizes. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-08-25Convert CONFIG_SYS_SPI_U_BOOT_OFFS to KconfigHannes Schmelzer
This converts the following to Kconfig: CONFIG_SYS_SPI_U_BOOT_OFFS Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> [trini: Expose this for SPL_SPI_SUNXI for now] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 1Hannes Schmelzer
Some boards have coded this offset with formula or bitshifts in their board-config. Manually convert these things into hex-values to be able using moveconfig.py afterwards. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-02Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_USE_PREBOOT CONFIG_PREBOOT Both are together in one commit, since otherwise the former causes kconfig to define the latter, which gives duplicate symbol errors. Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the backslash lands in the wrong place. Similarly with socfpga_vining_fpga. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-02Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOTSimon Glass
In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be defined for each board. To prepare for conversion to Kconfig, add this. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-04-13imx: move CONFIG_VIDEO_IPUV3 to defconfigsAnatolij Gustschin
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-03-25Convert CONFIG_ENV_SPI_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-08-17Convert CONFIG_MISC_INIT_R to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-22Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27Convert CONFIG_SPI to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-11spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
2018-04-08Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to KconfigAlex Kiernan
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-02-23Remove config_distro_defaults.hAdam Ford
With the contents of config_distro_defaults.h migrated to Kconfig, we can remove this header file completely Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-13spi: Migrate CONFIG_MXC_SPI to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-08Convert CONFIG_APBH_DMA et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_APBH_DMA CONFIG_APBH_DMA_BURST CONFIG_APBH_DMA_BURST8 Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> [trini: Add in MMC as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-08Convert CONFIG_NAND_MXS to KconfigStefan Agner
This converts CONFIG_NAND_MXS to Kconfig. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-01-12ARM: imx: cm_fx6: env: try to determine dtb to useChristopher Spinrath
Some distributions like Fedora expect U-Boot to select a proper devicetree. Since there are several variants of the cm-fx6 module featuring different SoC variants and the module can be paired with several baseboards, it is not viable to hardcode a filename. Instead, follow the lead of other i.MX6 based devices and try to determine the devicetree to use with the help of the board name and the SoC variant exported by the board code, before calling the distro bootcommand. For now, only for the Utilite Pro a proper devicetree filename is known but further variants of the Utilite Computer or other devices based on the cm-fx6 module may be added in the future. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
2018-01-12ARM: imx: cm_fx6: export board and soc info to envChristopher Spinrath
Like many other i.MX6 based boards, there are multiple variants of the cm-fx6 module featuring different SoC variants. Furthermore, the module can be paired with multiple baseboards. At the same time modern distribution like Fedora require U-Boot to select a proper devicetree which depends on the SoC variant and the baseboard. Thus, export the SoC variant and the actual board to the environment following the conventions of other i.MX6 devices (e.g. the NXP boards) such that the environment can select a devicetree file to load. For now, we only know for sure that the cm-fx6 module and the SB-fx6m baseboard amount to a Utilite Computer variant (depending on the SoC). Further combinations may be added in the future; e.g. CompuLab's evaluation board once someone can verify the identification string stored in its eeprom. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-01-03ARM: imx: cm_fx6: env: don't run boot scripts twiceChristopher Spinrath
Boot scripts located in the root directory of the first partition of USB, mmc, and SATA drives are executed twice: first by the distro boot command and then by the legacy boot command. This may have weird side effects if those scripts only change or extend the environment (including parts of the boot command itself). Removing the script execution from the legacy boot command has its own caveats. For instance, the distro boot command may execute the boot.scr on the mmc drive, then the boot.scr on the SATA drive, before the legacy boot command actually boots from the mmc drive. However, the current behavior would only execute the boot.scr once more before the actual boot, but it does not prevent the script located on the SATA drive from being executed, and thus, both scripts from being mixed up. Considering that the legacy boot command is only in place to boot old (standard) installations, let's go with the resolution having less custom code and remove the script execution from the legacy boot command. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-03ARM: imx: cm_fx6: env: support distro boot commandChristopher Spinrath
The current default environment of the cm_fx6 is not suitable for booting modern distributions. Instead of extending the custom environment, let's use the distro boot command, which has been developed for precisely this use case. If the distro boot command fails, fall back to the old behavior (except for USB drives where the old behaviour is completely covered by the distro boot command). That way it is still possible to create "rescue SD cards" for old installations (e.g. if one messes up the on-flash environment). Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-03ARM: imx: cm_fx6: env: use standard variablesChristopher Spinrath
In preparation for supporting the distro boot command, introduce the standard variables for specifying load addresses, which are documented in README and doc/README.distro, and replace the custom variables used so far with them. Since the current address layout disregards an address for an initramfs, also switch to the load addresses used and proven by other imx6 boards (e.g. the wandboard and nitrogen6x), instead of going on with our own way. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-12ata: Migrate CONFIG_LIBATA to KconfigTuomas Tynkkynen
This symbol enables some library code used by various SATA drivers, so make this a non-user-visible symbol select'ed by the respective drivers, and let moveconfig handle the rest. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_DWC_AHSATA to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-11-05Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-11ipu_common: Let the MX6 IPU clock be calculated in run-timeFabio Estevam
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz. When running a SPL target, which supports multiple MX6 variants we cannot properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as such decision is done in build-time currently. Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be configured in run-time on mx6. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de> [agust: fixed #endif in cgtqmx6eval.h] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-09-03include/configs: drop default definitions of CONFIG_SYS_PBSIZEThomas Petazzoni
Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-31configs: Migrate CMD_NAND*Tom Rini
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-25Convert CONFIG_ENV_IS_IN_SPI_FLASH to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_SPI_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-24configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFSTom Rini
The above CONFIG options are in Kconfig, and now have correct depends and inter-dependencies. Migrate these to configs/ from include/configs/. In the case of CMD_UBIFS also change it to be a default y if CMD_UBI. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-11Convert CONFIG_CMD_SATA to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_SATA Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-05-22Convert CONFIG_CMD_EEPROM et al to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_EEPROM_LAYOUT_HELP_STRING Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Rework Kconfig logic slightly, define EEPROM location on TI eval platforms] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30Convert CONFIG_CMD_BMP to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_BMP Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add depends on LCD || DM_VIDEO || VIDEO] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06Remove various unused interrupt related codeTom Rini
With d53ecad92f06 some unused interrupt related code was removed. However all of these options are currently unused. Rather than migrate some of these options to Kconfig we just remove the code in question. The only related code changes here are that in some cases we use CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename and move the value local to the code in question. Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-19Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich
Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-18spl: Remove CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORSSemen Protsenko
This option isn't used for anything, so get rid of it. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2016-11-18spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to KconfigSemen Protsenko
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Fix sniper and kc1 migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_SYS_STDIO_DEREGISTER to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_STDIO_DEREGISTER This option should never be enabled in SPL, so use CONFIG_IS_ENABLED(SYS_STDIO_DEREGISTER) when checking the option. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-sync] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VIDEO_SW_CURSOR to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VIDEO_SW_CURSOR Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Re-convert, find all the cases where this is off] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VGA_AS_SINGLE_DEVICE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VGA_AS_SINGLE_DEVICE Once we migrate to driver model for video, we should be able to drop this option. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-23Convert CONFIG_CFB_CONSOLE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CFB_CONSOLE Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-23Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VIDEO to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VIDEO Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-15spl: move FDT_FIXUP_PARTITIONS to KconfigHeiko Schocher
Move FDT_FIXUP_PARTITIONS to Kconfig and cleanup existing uses. Signed-off-by: Heiko Schocher <hs@denx.de>
2016-09-16Convert CONFIG_SPL_SPI_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-28 16:41:18 +0000