| Age | Commit message (Collapse) | Author |
|---|
|
Remove platform CONFIG_SYS_HZ definition for configs a-z*.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
|
|
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
|
|
these variables are curently defined in several config files but the
driver doesn't use them and defaults to hardcoded values in
nand_defs.h
It's interesting to be able to change this hardcoded valude when the
hardware is not using the default adress signals to drive ALE and CLE
and two configuration defines already exist for this purpose so use
them.
Signed-off-by: Eric Bénard <eric@eukrea.com>
|
|
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.
IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This define does not control anything, remove it.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
|
|
This change follows the change by Wolfgang Grandegger (commit 6c869637fef),
which allows to remove useless NAND_MAX_CHIPS definitions in board config
files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Add support for enabling NAND boot mode in configuration file and
add correspanding pinmux support, nand initialize function in board file.
The size required for environment variables not more than 10KB
the CONFIG_ENV_SIZE is set to 10KB from (512 << 10).
Acked-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This commit fixes a build warning in the DA830 EVM build
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Modify the MEMTEST start and end address. The memtest range was overlapping the
CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the
size for which mtest is run to 32MB from 16MB.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Enable SPI flash boot mode in configuration file as default.
With the introduction of 456MHz part, SPI operating frequency
will increase and at this frequency SPI does not work correctly.
Hence reduce the default SPI speed to 30MHz from 50MHz.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as
there are many variants of da830 based boards which have diffrent
names such as L137, AM1707 etc.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Some boar config files defined DEF_BOOTM but this was not used
anywhere in the code. Remove this bogus define.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Fixes build breakage in da830evm after commit
97003756249bd790910417eb66f0039bbf06a02c "da8xx: fixup ARM
relocation support"
The da8xx fixup commit changed da830/da850 common code to make
relocation work in da850, but didn't add the required defines
to da830evm_config.h resulting in build failure in the common code.
This patch adds those defines for da830, but makes no sense without
also referring to the commit mentioned above.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().
With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
|
|
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
now unnecessary config.mk file.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.
This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.
This patch is verified on da830/omap-l137, dm365 and dm644x evms.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Adds support for ethernet networking on the da830evm platform.
This platform uses an SoC EMAC interface and a 3 port ethernet
switch as a PHY with an RMII interface. The PHY also has a i2c
interface for configuring the switch functions.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
The EVM UI extender card has a NAND device. This change will enable
saveenv to work with NAND and Linux to be booted using:
mtdparts default
nboot kernel
bootm
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Adding USB configuration. Default is set for USB MSC host.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
|
|
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
Digital EVM board. See http://www.spectrumdigital.com/
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
|
