summaryrefslogtreecommitdiff
path: root/include/configs/display5.h
AgeCommit message (Collapse)Author
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-03-25Convert CONFIG_ENV_SPI_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-10-22Kconfig: Convert CONFIG_IMX_WATCHDOG to KconfigXiaoliang Yang
Move this option to Kconfig and tidy up the config file of eight boards which use it. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
2018-08-24ARM: display5: Remove "factory procedure" from display5 board configLukasz Majewski
This code now is regarded as dead one and hence shall be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-08-20display5: Introduce fitImg_fw_sz variableLukasz Majewski
This cosmetic change allow easy adjustment of the to-load kernel size if needed. Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-08-17Convert CONFIG_MISC_INIT_R to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Migrate bootlimit to KconfigAlex Kiernan
Migrate boards which set bootlimit in the environment to Kconfig. We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting if we migrated it. display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME, but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to set bootlimit= in display5_factory_defconfig. This is okay because the display5_factory_defconfig doesn't need to have it set, as it is only meant to prepare the board in the factory. Environment changes for all modified configs as seen from buildman: boards.cfg is up to date. Nothing to do. Summary of 3 commits for 32 boards (8 threads, 1 job per thread) 01: Merge git://git.denx.de/u-boot-x86 arm: + draco etamin rastaban pxm2 display5 thuban rut 02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit 03: Migrate bootlimit to Kconfig - display5_factory: bootlimit=3 Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-22Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-18display5: config: Add GPT verification and restoration code on SWUpdate entryLukasz Majewski
If GPT gets broken, then after N boot attempts we will run the SWUpdate restoration image. On its enter we will check GPT and restore it if needed. To test it: display5 > mmc write 0x12000000 4 8 It will overwrite the primary GPT table. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Reduce rootfs2 (BACKUP) size from 1528M to 512MLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Add cma=256M to command line argumentsLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Update swupdate initramfs file name (now supporting ext4)Lukasz Majewski
After moving to swupdate 2017.07, the default fs for swupdate rootfs is ext4, not ext3. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: factory: Update BACKUP rootfs in factory modeLukasz Majewski
After splitting rootfs images to BACKUP and ACTIVE, the "factory" u-boot also needs to update the former. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Provide 'tftp_mmc_rootfs_bkp' command to write BACKUP rootfsLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: wdt: Enable WDT support (both SPL and u-boot)Lukasz Majewski
Test case: The fitImage gets corrupted: truncate -c -s 3M fitImage run tftp_mmc_fitImg setenv boot_os y reset [board shall hang in SPL with "Trying to boot from MMC1" information] Then after X seconds WDT is causing board to reset. After N boot attempts we enter recovery mode. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: Support for the emergency PAD pressingLukasz Majewski
To enter the special mode, one needs to short cut two pads with e.g. screw driver. After power up the SPL will execute u-boot in which proper actions will be taken. It is worth noting that we do not alter envs (even the BOOT_FROM variable) and unconditionally go to recovery. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Update SPI-NOR partition for larger swupdate-initramfsLukasz Majewski
The SPI-NOR partition information has been updated to store swupdate-kernel-FIT just after envs as well as two times larger swupdate-initramfs image. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Remove support for Linux initramfs recovery image bootLukasz Majewski
This is a prerequisite patch to combine SWUpdate and Linux recovery initramfs images. It removes the support for it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Reset the board when bootm failsLukasz Majewski
Since display5 is now supporting boot counting, we can just reset the board when bootm fails (i.e. it doesn't boot the fitImage kernel for any reason). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Provide command to flash the whole SPI-NOR memoryLukasz Majewski
It may be necessary to update the content of the whole SPI-NOR memory at once with using a single command (tftp_sf_img). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Add "factory" (1MiB) SPI-NOR partition in u-bootLukasz Majewski
To test if this partition is present - one needs to write: display5 > sf probe; mtdparts display5 > sf erase factory +0x100000 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: factory: Setup IP config data according to LEG production ↵Lukasz Majewski
setup Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: factory: Add support for BOOT_FROM = FACTORY switchLukasz Majewski
When BOOT_FROM = FACTORY, then the LEG's factory setup is performed. This code relies on boot_nfs u-boot command, so it shall be adjusted appropriately (e.g. provide proper fitImage file). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-11spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
2018-04-08treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-13spi: Migrate CONFIG_MXC_SPI to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2017-11-09imx:display5: Add support for LWN's DISPLAY5 boardLukasz Majewski
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-24 00:07:25 +0000