| Age | Commit message (Collapse) | Author |
|---|
|
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver. Some SPLs need software ECC but others can't
fit it.
All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
|
|
The common spl framework expects the u-boot payload size through
CONFIG_SYS_MONITOR_LEN. Define the macro with the u-boot's size. With
this change, CONFIG_SYS_NAND_U_BOOT_SIZE is no longer required. Delete
the same.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.
IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
Parameters used for configuring certain SoC peripherals are parsed
from the cfg file and appended as part of the ais image's header. The
u-boot-spl.ais generated is flashed separately to the nand, so do not
delete the file after generation of u-boot.ais.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
Hawkboard was using the wrong nand_read_page version for SPL image.
As a side effect, the u-boot image loaded by the SPL from nand
was getting corrupted.
Enable CONFIG_SYS_NAND_HW_ECC_OOBFIRST to select the correct nand_read_page
algorithm for SPL.
Signed-off-by: Linu Cherian <linucherian@gmail.com>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
|
|
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This define does not control anything, remove it.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
With older toolchains we need CONFIG_SPL_LIBGENERIC_SUPPORT in order for
CONFIG_SPL_NAND_SUPPORT to link.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
|
|
The V bit of the c1 register of CP15 should not be cleared on DA850
SoCs since they have no valid memory at 0x00000000. This patch
introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH
that allows setting the correct value for the V bit.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
|
|
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
|
|
This change follows the change by Wolfgang Grandegger (commit 6c869637fef),
which allows to remove useless NAND_MAX_CHIPS definitions in board config
files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@googlemail.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the hawkboard use these definitions instead of
defining its own.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
