summaryrefslogtreecommitdiff
path: root/include/configs/km
AgeCommit message (Collapse)Author
2017-01-04ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLSYork Sun
These two macros are used for the same thing, the total number of DDR controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and merge existing usage. Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04fsl_ddr: Move DDR config options to driver KconfigYork Sun
Create driver/ddr/fsl/Kconfig and move existing options. Clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com> [trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-04powerpc: E500: Move CONFIG_E500 and CONFIG_E500MC to KconfigYork Sun
Use Kconfig option for E500 and E500MC macros. Signed-off-by: York Sun <york.sun@nxp.com>
2016-12-02powerpc: mpc85xx: Move CONFIG_FSL_LAW to KconfigYork Sun
Some header files have this macro defined conditionally and redefined unconditionally. Remove all existing definitions. Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23powerpc: P2041: Remove macro CONFIG_PPC_P2041York Sun
Replace CONFIG_PPC_P2041 with ARCH_P2041 in Kconfig and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
2016-10-28pci: Move CONFIG_PCI_PNP to KconfigBin Meng
Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig to use that. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Re-generate configs and include/configs/ changes] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-27drivers/pci/Kconfig: Add PCITom Rini
Add 'PCI' as a menu option and migrate all existing users. Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-10-23video: Drop CONFIG_CONSOLE_INFO_QUIETSimon Glass
This is not used in U-Boot. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-12common: Add DISPLAY_BOARDINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-12common/Kconfig: Add DISPLAY_CPUINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-26kconfig: introduce kconfig for UBIHeiko Schocher
move the UBI config options into Kconfig. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andrew F. Davis <afd@ti.com> Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
2016-09-09common, kconfig: move VERSION_VARIABLE to KconfigHeiko Schocher
move VERSION_VARIABLE from board config file into a Kconfig option. Signed-off-by: Heiko Schocher <hs@denx.de>
2016-08-05treewide: move CONFIG_PHYS_64BIT to KconfigMasahiro Yamada
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so that it is always available to the build system. Otherwise we can run into cases where we have inconsistent sizes of certain attributes. Ravi Babu reported offset mismatch of struct dwc3 across files since commit 95ebc253e6d4 ("types.h: move and redefine resource_size_t"). Since the commit, resource_addr_t points to phys_addr_t, whose size is dependent on CONFIG_PHYS_64BIT for ARM architecture. I tried my best to use "select" where possible (for example, ARMv8 architecture) because I think this kind of option is generally user- unconfigurable. However, I see some of PowerPC boards have 36BIT defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the defconfigs for such boards. CONFIG_36BIT is no longer referenced, so all of the defines were removed from CONFIG_SYS_EXTRA_OPTIONS. Fixes: 95ebc253e6d4 ("types.h: move and redefine resource_size_t") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Ravi Babu <ravibabu@ti.com> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-07powerpc: mpc85xx: kmp204x: Fix compiling error for usb errataYork Sun
Commit 9262367 moves USB errata workaround into a C file. This causes compiling error for kmcoge4 and kmlion1. To enable the errata workaround, define CONFIG_USB_EHCI_FSL in common header. Signed-off-by: York Sun <york.sun@nxp.com> Cc: Marek Vasut <marex@denx.de> Cc: Ed Swarthout <Ed.Swarthout@nxp.com> Cc: Sriram Dash <sriram.dash@nxp.com> Fixes: 92623672f9d3 ("fsl: usb: make errata function common for PPC and ARM")
2016-06-09common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig optionHeiko Schocher
move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-05-03include/configs: Numerous typo fixes: "controler" -> "controller".Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync almost all of cmd/KconfigTom Rini
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync HUSH optionsTom Rini
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14Merge git://git.denx.de/u-boot-dmTom Rini
2016-03-14Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14Drop CONFIG_CRAMFS_CMDLINESimon Glass
This option doesn't do anything. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-14Move CONFIG_OF_LIBFDT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing boards. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-25sf: Move SPI flash drivers to defconfigBin Meng
There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-25spi: Move SPI drivers to defconfigBin Meng
There are already Kconfig options for SPI drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-11-21eeprom: Zap CONFIG_SYS_I2C_MULTI_EEPROMSMarek Vasut
This option only complicates the code unnecessarily, just use CONFIG_SYS_DEF_EEPROM_ADDR as the default address if there are only five arguments to eeprom {read/write} if this is defined. If CONFIG_SYS_DEF_EEPROM_ADDR is not defined, we mandate all six arguments. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Heiko Schocher <hs@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-21ns16550: move CONFIG_SYS_NS16550 to KconfigThomas Chou
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2015-11-18km8309: change the default QE_FW addressValentin Longchamp
It should be after the u-boot reserved sectors and before the env sectors, since the solution used for kmvect1 (tell the linker to put the firmware into the u-boot produced binary, at the end of the area) should be the exception. The #define is only "conditional" so that we can still support kmvect1. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18km83xx: use CONFIG_ENV_ADDR for the newenv env commandValentin Longchamp
The hardcoded value are bad, since the address could change between different boards. Furthermore, the relevant #defines are set only if #undefined here, so that they can be changed by some boards if required. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18powerpc/km8309: define CONFIG_SYS_DDRCDRValentin Longchamp
For consistency with all the other km83xx plaforms, this should also be defined for km8309. The same settings as for km8321 are taken. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18powerpc/km8321: define CONFIG_SYS_DDRCDRValentin Longchamp
On the km8321 boards is CONFIG_SYS_DDRCDR not defined, which leads to the DDRCDR not being configured at startup and still containing the reset value. The required settings for our km8321 hardware designs are different than the reset value and must be set with CONFIG_SYS_DDRCDR, that is used by mpc83xx's cpu_init_f function at early CPU initialization. The important settings are the DDR2 internal voltage level and the half-strength "drivers". In our case where the DRAM chips are soldered on board and the routing for these signals under control, half-strength is sufficient as a few measurements done in the lasts have shown. Since all the hardware qualification tests have been performed with half strength, the nominal strength settings are removed in favor of the default reset half strength settings. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18km/powerpc: move open firmware defines to km-powerpc.hHolger Brunck
We use the same settings for open firmware defines on all our powerpc targets, so move them from the CPU specific headers to the common powerpc header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18km/powerpc: increase space for kernel imange and FDT blobHolger Brunck
128kByte and 3,986MB may be in the future too little for kernel the fdt blob respectively the kernel image. So increase the reserved areas here, we have the space for this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18km: update the boot script to check for a DTBValentin Longchamp
If a DTB is found with cramfsls, the bootscript continues as expected. If none is found, the cramfsloadfdt and boot subbootcmds are updated to not load the DTB from cramfs and not pass it to the kernel. The kernel thus must have an appended DTB otherwise the boot will fail. This is required for the km_kirkwood boards that must support .esw where the DTB sometimes is appended (for backwards compatibility) and sometimes is passed correctly (as we do now for all newer boards). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-18km/common: stop u-boot only if someone press <SPACE>Holger Brunck
To prevent u-boot to stop accidently e.g. due to line noise on the serial line, we now use the option CONFIG_AUTOBOOT_KEYED. We choose the <SPACE> key for this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-18arm/km_kirkwood: remove KM_ENV_BUS and use CONFIG_I2C_ENV_EEPROM_BUSValentin Longchamp
KM_ENV_BUS was used for nothing else than an direct assignment to CONFIG_I2C_ENV_EEPROM_BUS. To avoid this, directly use CONFIG_I2C_ENV_EEPROM_BUS instead. Patchwork: http://patchwork.ozlabs.org/patch/399411/ Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-10-24arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-21cmd: Convert CONFIG_CMD_ELF to KconfigBin Meng
Convert CONFIG_CMD_ELF to Kconfig and tidy up affected boards. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-21net: Move CONFIG_E1000 options to KconfigSimon Glass
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected boards. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-25Move defaults from config_cmd_default.h to KconfigJoe Hershberger
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25Move default y configs out of arch/board KconfigJoe Hershberger
Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-01net: Move the CMD_NET config to defconfigsJoe Hershberger
This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-01Move setexpr to KconfigJoe Hershberger
Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-03-30nand: Remove CONFIG_MTD_NAND_VERIFY_WRITEPeter Tyser
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some time and a more generic method of NAND verification now exists in U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2015-03-17mpc83xx: preempt premature board support removal by setting GENERIC_BOARDKim Phillips
Boards that haven't been converted to GENERIC_BOARD does *not* mean they should be removed. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2015-02-21ARM: kirkwood: move SoC headers to mach-kirkwood/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-kirkwood/* -> arch/arm/mach-kirkwood/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
2014-12-15mpc85xx: inhibit qman and bman portals by defaultJeffrey Ladouceur
Not all portals might be managed and therefore visible. Set the isdr register so that the corresponding isr register won't be set. This is required when supporting power management. Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-14keymile/powerpc: move to the architecture-generic board systemValentin Longchamp
This converts all the Keymile powerpc boards to the generic board initialization. This includes the 3 Keymile powerpc subsystems: km82xx, km83xx, and kmp204x. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-14mpc85xx/kmp204x: raise u-boot size to 768KBValentin Longchamp
Until now this defined to be 512KB and the total binary size actually was on the edge of this limit. Most of the powerpc boards have thus moved to 768KB. Since on the current kmp204x boards there is 1MB reserved for u-boot on the SPI boot flash, there is no problem to set the limit to 768KB as well to be on line with the other powerpc boards and to eventually configure in some additional features (and binary size) to u-boot. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-12km_arm: convert the km_arm boards to the generic board supportValentin Longchamp
This implies that all the km_kirkwood boards and their variants now are using the generic board init sequence. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
generated by cgit (git 2.34.1) at 2024-12-27 06:39:08 +0000