summaryrefslogtreecommitdiff
path: root/include/configs/ls1088aqds.h
AgeCommit message (Collapse)Author
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-19treewide: Remove unused FSL QSPI config options for Layerscape platformsKuldeep Singh
Some of these options are not used by the driver anymore and some of them are obsolete as the information is gathered from the dt. Also consolidating defines in common headers. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28Convert CONFIG_PHYLIB et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com>
2020-03-30configs: ls1088aqds: support distro bootBiwen Li
Add support of distro boot for ls1088aqds Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04armv8: ls1088a: Updates secure boot headers offsetPriyanka Singh
Updates the secure boot headers offsets of Kernel and other firmware images for SD and QSPI boot sources used by esbc_validate command. Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-08freescale/layerscape: Rename the config CONFIG_SECURE_BOOT nameUdit Agarwal
Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC to avoid conflict with UEFI secure boot. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-08-22armv8: ls1088aqds: support DSPI mode by hwconfigChuanhua Han
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used to control SPI and other IP signal routing. USBOSC: 0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz. SPI devices are unusable in this mode. 1= SPI_CLK used as SPI clock. SPI devices are usable in this mode. USB block is clocked from internal sources SPR[3:2]: SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]): 00= SDHC/eMMC 8-bit 01= SD Card Rev 2.0/3.0 10= SPI on-board memory 11= TDM Riser / SPI off-board connector. The default value is 00 if an SDCard/eMMC card is selected as the boot device. SPR[1:0]: SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]): 00= SDHC Sync loop 01= TDM Riser / SPI off-board connector. 10= SPI on-board memory. 11= SPI off-board connector. By default, the SPI feature is not available, so we need to configure the above register fields to select the route to the SPI feature. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1088aqds: Add support of I2C driver model.Chuanhua Han
Udate ls1088aqds board init code to support DM_I2C. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-01-17armv8: ls1088aqds: Add TFABOOT supportPankit Garg
TFABOOT support includes: - ls1088aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06ls1088a: Move CONFIG_FSL_QSPI to defconfigAshish Kumar
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-10-19Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to KconfigMario Six
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08treewide: Migrate CONFIG_SYS_ALT_MEMTEST to KconfigMario Six
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration after also including CMD_MEMTEST] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-20armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088Ashish Kumar
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT. Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and IFC-NOR to be used as flash. This allows writing to IFC-NOR flash. QSPI and DSPI cannot be accessed in this defconfig. IFC-NOR image is generated using ls1088aqds_defconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20armv8: ls1088qds: Remove CONFIG_ from local defines for FPGAAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-02-23Remove config_distro_defaults.hAdam Ford
With the contents of config_distro_defaults.h migrated to Kconfig, we can remove this header file completely Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-23Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-23armv8: ls1088a: Add IFC and eMMC as qixis boot sourcesAshish Kumar
Add macro QIXIS_LBMAP_EMMC, QIXIS_LBMAP_IFC, QIXIS_RCW_SRC_IFC, QIXIS_RCW_SRC_EMMC to enable IFC and eMMC as boot sources for qixis commands. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> [YS: Modify subject and add commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23ls1088a: Add VID support for QDS and RDB platformsRajesh Bhagat
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems. It reads the fusesr register and changes the VDD accordingly by adjusting the voltage via LTC3882 regulator. This patch also takes care of the special case of 0.9V VDD is present in fusesr register. In that case,it also changes the SERDES voltage by disabling the SERDES, changing the SVDD and then re-enabling SERDES. Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Add support for LTC3882 voltage regulator chipRajesh Bhagat
Restructures common driver to support LTC3882 voltage regulator chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-17armv8: ls1088ardb: Add environment variable address location for QSPI-NORAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06armv8: LS1088A_QSPI: SECURE_BOOT: Images validationUdit Agarwal
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC phase using esbc_validate command. Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment Add header address for PPA to be validated during ESBC phase for LS1088A platform based on LAyerscape Chasis 3. Moves sec_init prior to ppa_init as for validation of PPA sec must be initialised before the PPA is initialised. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088aqds: Add SD boot support for ls1088qdsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14armv8: ls1088a: Move CONFIG_SPI_FLASH_SPANSION to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27armv8: ls1088: Move CONFIG_ENV_IS_IN_SPI_FLASH to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-10configs: Re-sync CONFIG_CMD_IMLS with moveconfigTuomas Tynkkynen
The option is specified in Kconfig, but still a few config header files are overriding the choice by #undef'ing it. Re-sync the option with moveconfig to rid of the #undefs. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-09-11armv8: ls1088aqds: Add support of LS1088AQDSAshish Kumar
This patch add support of LS1088AQDS platform. The LS1088A QorIQTM Development System (QDS) is a high-performance computing, evaluation, and development platform that supports the LS1088A QorIQ Architecture processor. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-23 18:39:45 +0000