| Age | Commit message (Collapse) | Author |
|---|
|
This will fix the following error:
---8<---
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:root' errno=-12!
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: prafulla@marvell.com
Cc: dimax.main@gmail.com
Tested-by: Alex Xol <dimax.main@gmail.com>
|
|
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.
IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
This define does not control anything, remove it.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This change follows the change by Wolfgang Grandegger (commit 6c869637fef),
which allows to remove useless NAND_MAX_CHIPS definitions in board config
files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
commit 25ddd1fb0a2281b182529afbc8fda5de2dc16d96 left remnants of
many comments about CONFIG_SYS_GBL_DATA_SIZE.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
|
|
The asm/arch/config.h header define CONFIG_NR_DRAM_BANKS_MAX, which is
needed to configure DRAM banks.
This patch move the asm/arch/config.h header inclusion above the DRAM
banks configuration.
Additionally this patch fix a typo.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
|
|
Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.
This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.
This patch is tested with compilation for armada100 and guruplug.
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
This patch adds commonly used macros for ARMADA100 based
baords, Also some code reshuffled and updated for typos and comments
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Conflicts:
include/configs/km_arm.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
After moving the definition of CONFIG_SYS_TEXT_BASE to the respective
board config files, all Marvell kirkwood board have just a single and
common entry in their config.mk files:
KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
Replace the only reference to KWD_CONFIG in the top level Makefile by
an equivalent setting, and remove all kirkwood config.mk files.
Signed-off-by: Wolfgang Denk <wd at denx.de>
Cc: Prafulla Wadaskar <prafulla at marvell.com>
Cc: Siddarth Gore <gores at marvell.com>
Cc: Simon Kagstrom <simon.kagstrom at netinsight.net>
Cc: Heiko Schocher <hs at denx.de>
Cc: Eric Cooper <ecc at cmu.edu>
Acked-by: Wolfgang Denk <wd at denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
|
|
It has been observed that, the complete u-boot banner
does not appear on the console when the system is booted
from NAND/NOR/SPI flash.
This patch fixes this issue on all Marvell boards by adding
board_early_init_f() support
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
All Kirkwood based boards are supported for this new implementation
ref: docs/README.arm-relocation
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
It is observed that, in most of the board configs the code is being
duplicated, also for any common change all board files needs update
This issue was under discussion from long on mailing list and we
converge on introducing common config file.
With this patch-
1. Total Kirkwood specific configuration code is reduced by 210 lines
2. All common configuration can be shared by multiple boards
3. Easy to manage common updates like ARM relocation changes
mv-common.h file is added to include/configs/
It contains all common configuration supported for all Kirkwood boards
The respective board configs are updated for its usage
Build tested for guruplug, mv88f6281gtw_ge, openrd_base,
rd6281a and sheevaplug
Binary execution tested for sheevaplug
Todo:
1. Other custom Kirkwood boards to be synced
2. The support to be extended for Orion5X based boards
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
