summaryrefslogtreecommitdiff
path: root/include/configs/mx6sabre_common.h
AgeCommit message (Collapse)Author
2018-02-13spi: Migrate CONFIG_MXC_SPI to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-04mx6sabresd: Select CONFIG_CMD_USB_MASS_STORAGEFabio Estevam
Select CONFIG_CMD_USB_MASS_STORAGE so that the 'ums' can be used. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04mx6sabre_common: Allow building CONFIG_USB_FUNCTION_MASS_STORAGEFabio Estevam
Selecting CONFIG_USB_FUNCTION_MASS_STORAGE=y in the defconfig leads to the following error: cmd/built-in.o: In function `do_usb_mass_storage': cmd/usb_mass_storage.c:217: undefined reference to `fsg_main_thread' cmd/usb_mass_storage.c:170: undefined reference to `fsg_init' CONFIG_USB_FUNCTION_MASS_STORAGE option is built only for the non-SPL case as per the logic in drivers/usb/gadget/Makefile, so remove the incorrect CONFIG_SPL ifdefery to fix the build failure. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Shawn Guo <shawn.guo@linaro.org>
2018-02-02Kconfig: gadget: Move CONFIG_USB_FUNCTION_MASS_STORAGE to KconfigLukasz Majewski
This commit moves USB_FUNCTION_MASS_STORAGE config to Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-09-11ipu_common: Let the MX6 IPU clock be calculated in run-timeFabio Estevam
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz. When running a SPL target, which supports multiple MX6 variants we cannot properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as such decision is done in build-time currently. Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be configured in run-time on mx6. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de> [agust: fixed #endif in cgtqmx6eval.h] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-09-01Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigsTom Rini
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's not strictly part of fastboot. - Add some defaults for the fastboot buffer location and size - Migrate all options listed in cmd/fastboot/Kconfig - Cleanup the README Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-25Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-12mx6sabre: Use PARTUUID to specify the rootfs locationFabio Estevam
mx6sabre boards can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the eMMC changes depending on the kernel version. In order to avoid such issue, use UUID method to specify the rootfs location. Succesfully tested booting a NXP 4.1 and also a mainline kernel on a mx6qsabresd and mx6dlsabreauto. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-04-30Convert CONFIG_CMD_BMODE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_BMODE Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Make this default y and depend on mx5/6/7] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06Remove various unused interrupt related codeTom Rini
With d53ecad92f06 some unused interrupt related code was removed. However all of these options are currently unused. Rather than migrate some of these options to Kconfig we just remove the code in question. The only related code changes here are that in some cases we use CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename and move the value local to the code in question. Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-25Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-21config: Move CONFIG_BOARD_LATE_INIT to defconfigsJagan Teki
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-10-23Convert CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VGA_AS_SINGLE_DEVICE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VGA_AS_SINGLE_DEVICE Once we migrate to driver model for video, we should be able to drop this option. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-23Convert CONFIG_CFB_CONSOLE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CFB_CONSOLE Signed-off-by: Simon Glass <sjg@chromium.org>
2016-10-23config: Drop CONFIG_CONSOLE_DEVSimon Glass
This is not really a config. Rename it to avoid confusion. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-23Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23Convert CONFIG_VIDEO to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_VIDEO Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-27dfu: Migrate to KconfigTom Rini
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for CMD_DFU (as we must have the DFU command enabled to do anything DFU). Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add options for all of the back end choices that DFU can make use of. Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25include/configs: Whitespace fixupTom Rini
A number of moveconfig.py runs have left a instances of multiple empty lines in a row. Correct this to a single empty line. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync almost all of cmd/KconfigTom Rini
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-20usb: gadget Move: CONFIG_G_DNL_* to KconfigSam Protsenko
And also reformat defconfigs using "make savedefconfig" rule. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2016-04-20usb: gadget: Move CONFIG_USB_GADGET_DOWNLOAD to KconfigSam Protsenko
While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some config headers. This is also probably fixes am335x_baltos board. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2016-04-20usb: gadget: Move CONFIG_USB_GADGET_DUALSPEED to KconfigSam Protsenko
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and make all UDC controllers select USB_GADGET_DUALSPEED: - add next options to Kconfig selecting USB_GADGET_DUALSPEED: - USB_GADGET_ATMEL_USBA - USB_GADGET_DWC2_OTG - USB_DWC3 - CI_UDC - make USB_MUSB_GADGET select USB_GADGET_DUALSPEED While at it, make some related fixes: - remove DUALSPEED from configs that don't enable gadget support: - kwb.h - tseries.h - add missing USB_GADGET option to next configs: - novena_defconfig - pcm051_rev*_defconfig - xfi3_defconfig Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2016-04-20usb: gadget: Move CONFIG_USB_GADGET_VBUS_DRAW to KconfigSam Protsenko
The description was borrowed from kernel. Definitions were added to defconfig files in a way that "make savedefconfig" generates exactly the same file as used defconfig. Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use 2 mA (as minimal allowed by Kconfig). Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2016-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-03-25usb: gadget: Move CONFIG_USB_GADGET to KconfigSam Protsenko
The description was borrowed from kernel. "tristate" type was changed to "bool" (I believe we don't support modules for u-boot yet, right?). CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along as well. Definitions were added to defconfig files in a way that "make savedefconfig" generates exactly the same file as used defconfig. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Add zynq_zc702 conversion] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-25mx6sabre_common: Fix U-Boot corruption after 'saveenv'Fabio Estevam
Booting mx6qp sabreauto board and then doing: => saveenv => reset , causes a system hang. This happens because the size of the U-Boot binary is larger than CONFIG_ENV_OFFSET. Fix this problem by increasing CONFIG_ENV_OFFSET, so that the U-boot binary and the environment variables region do not overlap. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-14imx: mx6: correct IPU clockPeng Fan
The CONFIG_IPUV3_CLK should be 264000000, to i.MX6DL, it should be 198000000. Signed-off-by: Peng Fan <van.freenix@gmail.com> Signed-off-by: Sandor Yu <sandor.yu@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Peter Robinson <pbrobinson@gmail.com>
2015-11-25sf: Move SPI flash drivers to defconfigBin Meng
There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-10-30imx: mx6sabresd: add i.MX6DQP Sabresd supportPeng Fan
Add i.MX6DQP-Sabresd board support: 1. set fdt_file according to board_rev which is set at runtime. 2. Add mx6dqp_ddr_ioregs and calibration value for this board. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-10-02mx6sabre_common: Add DFU supportFabio Estevam
Add DFU support. Tested by flashing SPL and u-boot.img into SPI NOR flash with the following commands: => setenv dfu_alt_info ${dfu_alt_info_spl} => run dfuspi On the host PC: $ sudo dfu-util -D SPL -a spl On the target: CTRL+C => setenv dfu_alt_info ${dfu_alt_info_img} => run dfuspi On the host PC: $ sudo dfu-util -D u-boot.img -a u-boot Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20mx6sabre_common: Add Fastboot supportFabio Estevam
Tested basic fastboot commands, such as: On the mx6qsabresd U-boot prompt: => fastboot 0 On the host PC: $ fastboot getvar bootloader-version -i 0x0525 bootloader-version: U-Boot 2015.10-rc2-23960-g2462cce-dirty finished. total time: 0.000s $ fastboot reboot -i 0x0525 --> board reboots fine. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-13thermal: imx_thermal: rework driver to be reusedAdrian Alonso
Rework imx_thermal driver to be used across i.MX processor that support thermal sensor Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-08-02Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-08-02imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board supportPeng Fan
1. Add DDR script for mx6qpsabreauto board. 2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9] and init the enet pll output to 125Mhz. 3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN. Build target: mx6qpsabreauto_config Boot Log: U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 34C Reset cause: POR Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB PMIC: PFUZE100 ID=0x10 Flash: 32 MiB NAND: 0 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Note: In this patch, we still add a new config mx6qpsabreauto_config, since SPL is not supported now, and IMX_CONFIG is needed at build time, so add this config. Future, when SPL is converted, this config can be removed. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-08-02imx: mx6sabresd/sabreauto runtime setting fdt_filePeng Fan
Detect the SOC and board variant at runtime and change the dtb name, but not hardcoding the fdt_file env variable. Take the following patch as a reference. Íd58699b157df75f1aa0b363ea9c21add21a0c "mx6cuboxi: Load the correct 'fdtfile' variable" Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2015-07-22usb: USB download gadget and functions config options coherent namingPaul Kocialkowski
This introduces a coherent scheme for naming USB download gadget and functions config options. The download USB gadget config option is moved to CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each function's config option is moved to a CONFIG_USB_FUNCTION_ prefix. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
2015-07-10imx6: standardise OCOTP and fuse config to mx6_commonPeter Robinson
According to README.mxc_ocotp the OCOTP is a stanard i.MX6 SoC feature so centralise the config in mx6_common.h so functionality is standard across all boards Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2015-06-25Move default y configs out of arch/board KconfigJoe Hershberger
Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-01net: Move the CMD_NET config to defconfigsJoe Hershberger
This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-01Move setexpr to KconfigJoe Hershberger
Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-05-26mx6: standardise CONFIG_CMD_CACHEPeter Robinson
Move CONFIG_CMD_CACHE to mx6_common and standardise the way it's defined. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
2015-05-26imx6: generic MMC config options to mx6_commonPeter Robinson
Move all standard mx6 MMC configs to mx6_common. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Tom Rini <trini at konsulko.com>
2015-05-26imx6: standardise filesystem and boot optionsPeter Robinson
Move all standard filesystem, partition and fdt options to mx6_common. Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2015-05-26imx6: move generic miscellaneous and overwrite optionsPeter Robinson
Move generic miscellaneous options that are standard across most, if not all, mx6 boards to central mx6_common define to ensure consistent features. Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2015-05-26imx6: centralise common boot options in mx6_common.hPeter Robinson
Define common LOADADDR and BOOTDELAY to ensure a consistent experience across mx6 boards Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2015-05-26imx6: move MXC_GPIO define to mx6_common.hPeter Robinson
Define CONFIG_MXC_GPIO and CONFIG_CMD_GPIO by default in mx6_common Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-28 01:07:16 +0000