summaryrefslogtreecommitdiff
path: root/include/configs/tqma6.h
AgeCommit message (Collapse)Author
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-18common: Drop linux/stringify.h from common headerSimon Glass
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-04-17configs: tqma6x_mba6x: update default configs for device modelMichael Krummsdorf
Fixes compilation for WRU4 board. Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-12defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENTTom Rini
Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-03-25Convert CONFIG_ENV_SPI_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-13spi: Migrate CONFIG_MXC_SPI to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-08usb: net: migrate USB Ethernet adapters to KconfigChris Packham
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08usb: net: migrate CONFIG_USB_HOST_ETHER to KconfigChris Packham
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-25Convert CONFIG_ENV_IS_IN_SPI_FLASH to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_SPI_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22Convert CONFIG_CMD_EEPROM et al to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_EEPROM_LAYOUT_HELP_STRING Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Rework Kconfig logic slightly, define EEPROM location on TI eval platforms] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22Drop digital thermometer and thermostat (DTT) driversSimon Glass
This subsystem is quite old. It has been replaced with a driver-model version (UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-15Kconfig: USB: Migrate existing USB_EHCI_xxx optionsTom Rini
The following options are migrated over fully now: - USB_EHCI_ATMEL - USB_EHCI_MARVELL - USB_EHCI_MX6 - USB_EHCI_MX7 - USB_EHCI_MSM - USB_EHCI_ZYNQ - USB_EHCI_GENERIC This also requires fixing the depends on USB_EHCI_MARVELL as it's used by Orion5X and Kirkwood as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to KconfigTom Rini
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig. For a few SoCs, imply or default y this if USB is enabled. In some cases we had not already migrated to CONFIG_USB so do that as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCDTom Rini
In order to be able to migrate the various SoC EHCI CONFIG options we first need to finish the switch from CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
2017-04-30Convert CONFIG_CMD_BMODE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_BMODE Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Make this default y and depend on mx5/6/7] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06Remove various unused interrupt related codeTom Rini
With d53ecad92f06 some unused interrupt related code was removed. However all of these options are currently unused. Rather than migrate some of these options to Kconfig we just remove the code in question. The only related code changes here are that in some cases we use CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename and move the value local to the code in question. Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-17arm: imx6: tqma6: add support for TQMa6DL variantMarkus Niebel
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM Since The module will use the same devicetree, we patch the ram size in ft_board_setup. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17arm: imx6: tqma6: use CONFIG_TQM6x for SOM specific settingsMarkus Niebel
We have a Kconfig name for the module types. Let's Use it. Some feature selections and configurations are based on the module. Module selection selects the CPU type. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-02-19tqma6: [cosmetic] sanitize environment definesMarkus Niebel
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-02-19tqma6: fix rounding in envMarkus Niebel
need to add before div in mmc update scripts. Otherwise we could write one block more ba acident Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-02-19mx6: tqma6: add rootfsmode environment for mmc / sdMarkus Niebel
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-02-19mx6: tqma6: fix typo in envMarkus Niebel
there was a double bracketed var ref. fix this. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-02-19imx6: tqma6: rely on default setting for tftp and nfsMarkus Niebel
Playing with USB-to-Ethernet dongles it turns out, that these will not work with special settings Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-02-19arm: imx6: tqma6: add configurable CMA sizeMarkus Niebel
depending on the use case different CMA sizes are needed for linux. Add env var to enable passing CMA size via kernel command line Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-01-25Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-21config: Move CONFIG_BOARD_LATE_INIT to defconfigsJagan Teki
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-10-23config: Drop CONFIG_CONSOLE_DEVSimon Glass
This is not really a config. Rename it to avoid confusion. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-16Convert CONFIG_SPL_SPI_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16Convert CONFIG_SPL_MMC_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16Convert CONFIG_SPL_FAT_SUPPORT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-09configs: Migrate CONFIG_USB_STORAGETom Rini
In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-17ARM: mx6: Enable MMC and SATA extfs boot supportMarek Vasut
Enable support for booting U-Boot image from ext filesystem when either SD/MMC or SATA support is compiled into the SPL. This will allow easy transition from loading U-Boot image from ad-hoc offset on the card to loading U-Boot image from the filesystem. VFAT support is intently not enabled. The boot order is tweaked so that raw is tested first and if the raw has no signature, FS boot is attempted. To install just the SPL on i.MX6 board, perform the following operation $ dd if=SPL of=/dev/sdX seek=2 bs=512 To install the U-Boot image, copy u-boot.img to the first partition of the SD/MMC/SATA drive. The partition must be formated to extfs. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25include/configs: Whitespace fixupTom Rini
A number of moveconfig.py runs have left a instances of multiple empty lines in a row. Correct this to a single empty line. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25configs: Re-sync almost all of cmd/KconfigTom Rini
This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14Move CONFIG_OF_LIBFDT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing boards. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-25sf: Move SPI flash drivers to defconfigBin Meng
There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-10-02I2C: mxc_i2c: make I2C1 and I2C2 optionalAlbert ARIBAUD \\(3ADEV\\)
The driver assumed that I2C1 and I2C2 were always enabled, and if they were not, then an asynchronous abort was (silently) raised, to be caught much later on in the Linux kernel. Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4 are. To make the change binary-invariant, declare I2C1 and I2C2 in every include/configs/ file which defines CONFIG_SYS_I2C_MXC. Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed (CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE) config options. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-07-26arm: mx6: tqma6: Add WRU-IV baseboard for the TQMa6 SoMStefan Roese
This patch adds support for the "OHB System AG" baseboard with is equipped with the TQMa6S SoM. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
2015-07-10imx6: standardise OCOTP and fuse config to mx6_commonPeter Robinson
According to README.mxc_ocotp the OCOTP is a stanard i.MX6 SoC feature so centralise the config in mx6_common.h so functionality is standard across all boards Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2015-07-03Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
Conflicts: configs/tbs2910_defconfig configs/tqma6q_mba6_mmc_defconfig configs/tqma6q_mba6_spi_defconfig configs/tqma6s_mba6_mmc_defconfig configs/tqma6s_mba6_spi_defconfig include/configs/mx6_common.h Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2024-12-23 03:29:13 +0000