| Age | Commit message (Collapse) | Author |
|---|
|
Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite the FDT
and silently fail to boot.
On e300 CPUs, the Linux kernel uses an initial BAT covering the first
256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase
the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value
allowed by Linux. This will allow very large kernels to boot.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
before, MPC8349ITX boots u-boot in 4.3sec:
column1 is elapsed time since first message
column2 is elapsed time since previous message
column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA: Configured for compact flash
0.032 0.000: I2C: ready
0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI: Bus Dev VenId DevId Class Int
2.652 0.011: 00 10 1095 3114 0180 00
2.652 0.000: PCI: Bus Dev VenId DevId Class Int
2.652 0.000: In: serial
2.652 0.000: Out: serial
2.652 0.000: Err: serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE: Bus 0: .** Timeout **
after, MPC8349ITX boots u-boot in 3.0sec:
0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA: Configured for compact flash
0.038 0.000: I2C: ready
0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI: Bus Dev VenId DevId Class Int
1.390 0.000: 00 10 1095 3114 0180 00
1.390 0.000: PCI: Bus Dev VenId DevId Class Int
1.400 0.010: In: serial
1.400 0.000: Out: serial
1.400 0.000: Err: serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE: Bus 0: .** Timeout **
also tested on these boards (albeit with a less accurate
boottime measurement method):
seconds: before after
8349MDS ~2.6 ~2.2
8360MDS ~2.8 ~2.6
8313RDB ~2.5 ~2.3 #nand boot
837xRDB ~3.1 ~2.3
also tested on an 8323ERDB.
v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
because it's convenient.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
commit 98d92d8c9f4021629a45261ad5ec3f3595f3a27a "sbc8349: fix incorrect
comment" missed this one.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
changed to use mkconfig -t option instead, plus misc codingstyle fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
commit 6d0f6bcf337c5261c08fabe12982178c2c489d76 did the big
rename of CFG_ macros to CONFIG_SYS macros. But it missed
a couple of instances within comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This was introduced with the MPC8349EMDS board, and then copied to
a couple other boards by nature of being the reference implementation.
u-boot$git grep CONFIG_SYS_MID_FLASH_JUMP
include/configs/MPC8349EMDS.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/sbc8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/vme8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
u-boot$
It currently isn't used, so delete it before it spreads further.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
