summaryrefslogtreecommitdiff
path: root/include/configs/warp7.h
AgeCommit message (Collapse)Author
2019-12-06warp7: Fix U-Boot corruption after saving the environmentFabio Estevam
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" followed by a "reset" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Pierre-Jean Texier <pjtexier@koncepto.io> Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io> Acked-by: Joris Offouga <offougajoris@gmail.com> Tested-by: Joris Offouga <offougajoris@gmail.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-07-19warp7: Specify a default CONFIG_OPTEE_LOAD_ADDR if non providedBryan O'Donoghue
If no CONFIG_OPTEE_LOAD_ADDR is provided i.e. you are not loading OPTEE into memory in u-boot, then just set the non-existent CONFIG option to zero, elsewise stringify(CONFIG_OPTEE_LOAD_ADDR) will return "CONFIG_OPTEE_LOAD_ADDR" - which looks weird in the u-boot environment. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2019-07-19warp7: include: configs: Specify an fdtovaddrBryan O'Donoghue
In the Mbed Linux OS bootflow OP-TEE runs before u-boot and provides a DTB overlay at 0x83100000. This overlay should subsequently be merged into the main DTB before handing over to the kernel. This patch defines fdtovaddr at 0x83100000. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2019-07-19warp7: include: configs: Differentiate bootscript address from loadaddrBryan O'Donoghue
Reusing the loadaddr to load the boot script breaks some of the logic we want to have around the bootscript/FIT load addresses. Making a dedicated bootscript address allows us to differentiate the bootscript load address from the Linux Kernel or OPTEE load address, thus ensuring that no matter what the load sequence the bootscript and Kernel/OPTEE binary load addresses do not conflict. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2019-07-19warp7: include: configs: Specify image name of bootscript in FITBryan O'Donoghue
When obtaining the bootscript from a FIT image we need to specify the name of the bootscript as defined inside of the FIT. This patch makes a define that appends a "bootscr" parameter to the source command when compiling up in FIT mode on warp7. An environment variable is supplied to enable others to use a different name than "bootscr" as the image name of the boot script in their FIT. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2019-06-11mx7_common: Share configs to skip low level initJun Nie
Share configs in mx7 to skip low level init if we are in the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of the low level initialization is already done and that we may/should skip it doing them here. Fix the definition detection with size detection to decide whether to skip it. Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-04-25warp7: Switch to DM SerialPierre-Jean Texier
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-04-25warp7: Fix dfu_alt_info setting after DM conversionPierre-Jean Texier
After DM conversion, U-Boot is larger than 512 KiB, so we need to increase the "size" of the dfu_alt_info setting. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Acked-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-01-28arm: imx7s-warp: Convert to DM PMICBryan O'Donoghue
This patch converts the warp7 and warp7_bl33 board ports over to using the DM PMIC model. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28warp7: defconfig: Switch to DM for I2CBryan O'Donoghue
This commit switches to DM I2C for warp7 and warp7_bl33 defconfigs. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2018-10-22warp7: include: configs: set skip low level initRui Miguel Silva
If we have defined the OPTEE ram size and not OPTEE means that we are in the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of the low level initialization is already done and that we may/should skip it doing them here. Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: u-boot@lists.denx.de
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-26warp7: Add support for automated secure boot.scr verificationBryan O'Donoghue
This patch adds support for verifying a signed boot.scr. With this in place it's possible for run-time Linux to update boot.scr to set different variables such as switching between different boot partitions, pointing to different kernels etc and for u-boot to verify these changes via the HAB prior to executing the commands contained in boot.scr. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: hab: Set environment variable indicating IVT offsetBryan O'Donoghue
This patch introduces the environment variable ivt_offset. When we define a load address for Linux or DTB or any file the IVT associated with that file is prepended. We extract the actual load addresses from u-boot.cfg and feed these values into the code-signing process - hence we want u-boot to have the real load addresses exported in uboot.cfg. ivt_offset represents the addition or subtraction from the load address that must happen to find an IVT header. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: add warp7_auth_or_failBryan O'Donoghue
Doing secure boot on the WaRP7 using a common image format and the same variable to represent the base address for each call means we can reduce down the command to a single environment command. This patch adds warp7_auth_or_fail as a wrapper around "hab_auth_img_or_fail ${hab_ivt_addr} ${filesize} 0". Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: Define the name of a signed boot-script fileBryan O'Donoghue
We need to know the name of a signed boot-script, its better to have a separate variable for this then to simply append some fixed string to an existing image name. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: select uuid partition based on rootpartBryan O'Donoghue
Assigning the UUID discovery path to a tweakable environment variable means that later steps in the boot process - particularly a boot script can change the target root partition of a particular Linux boot. Retargeting the rootfs is an important feature when doing ping/pong upgrades allowing a boot script to select ping or pong as necessary without reprogramming the bootloader. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: Make CONFIG_SYS_FDT_ADDR a defineBryan O'Donoghue
In order to sign images with the IMX code-signing-tool (CST) we need to know the load address of a given image. The best way to derive this load address is to make it into a define - so that u-boot.cfg contains the address - which we can then parse when generating the IMX CST headers. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: Specify CONFIG_OPTEE_LOAD_ADDRBryan O'Donoghue
In order to sign images with the IMX code-signing-tool (CST) we need to know the load address of a given image. The best way to derive this load address is to make it into a define - so that u-boot.cfg contains the address - which we can then parse when generating the IMX CST headers. This patch makes the OPTEE_LOAD_ADDR available via u-boot.cfg for further parsing by external tools. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: hab: Set environment variable indicating HAB enableBryan O'Donoghue
This patch adds an environment variable called "hab_enabled" which gets set to a boolean status indicating whether HAB is enabled or not. Subsequent patches can use this environment variable to determine if its necessary to run a given binary through the hab_auth_img console command. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-26warp7: include/configs: use generic fs commands in CONFIG_EXTRA_ENV_SETTINGSPierre-Jean TEXIER
use the generic filesystem command 'load' rather than 'fatload' to avoid per-fs specific commands. Signed-off-by: Pierre-Jean TEXIER <texier.pj2@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2018-04-15warp7: Set u-boot serial# based on OTP valueBryan O'Donoghue
u-boot has a standard "serial#" environment variable that is suitable for storing the iSerial number we will supply via the USB device descriptor. serial# is automatically picked up by the disk subsystem in u-boot - thus providing a handy unique identifier in /dev/disk/by-id as detailed below. Storing the hardware serial identifier in serial# means we can change the serial# if we want before USB enumeration - thus making iSerial automatic via OTP but overridable if necessary. This patch reads the defined OTP fuse and sets environment variable "serial#" to the value read. With this patch in place the USB mass storage device will appear in /dev/disk/by-id with a unique name based on the OTP value. For example /dev/disk/by-id/usb-Linux_UMS_disk_0_WaRP7-0xf42400d3000001d4-0:0 Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Rui Miguel Silva <rui.silva@linaro.org> Cc: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-02Kconfig: gadget: Move CONFIG_USB_FUNCTION_MASS_STORAGE to KconfigLukasz Majewski
This commit moves USB_FUNCTION_MASS_STORAGE config to Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-10-03usb: gadget: usb_ether: Move the interfaces to KconfigMaxime Ripard
We need to select an interface for the usb_ether gadget, and they haven't been converted to Kconfig yet. Add a choice to make sure we have an option selected, and convert all the users. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03usb: gadget: Convert USB_ETHER to KconfigMaxime Ripard
The USB Ethernet gadget option has not yet been moved to Kconfig, let's deal with that. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03usb: gadget: Move USBNET_HOST_ADDR to KconfigMaxime Ripard
While the USB Ethernet device address is already defined in Kconfig, the host address isn't. Convert it. Reviewed-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-07-25Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06Remove various unused interrupt related codeTom Rini
With d53ecad92f06 some unused interrupt related code was removed. However all of these options are currently unused. Rather than migrate some of these options to Kconfig we just remove the code in question. The only related code changes here are that in some cases we use CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename and move the value local to the code in question. Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-12flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-28cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPTPatrick Delaunay
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-25Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-21config: Move CONFIG_BOARD_LATE_INIT to defconfigsJagan Teki
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-02ARM: imx7s-warp: enable USB gadget ethernetKevin Hilman
Enable USB gadget ethernet by default to have networking capabilities. Tested using DHCP and TFTP to transfer kernel, DT, ramdisk. Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-10-12common: Add DISPLAY_BOARDINFOLokesh Vutla
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-27dfu: Migrate to KconfigTom Rini
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for CMD_DFU (as we must have the DFU command enabled to do anything DFU). Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add options for all of the back end choices that DFU can make use of. Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2016-09-09configs: Migrate CONFIG_USB_STORAGETom Rini
In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-06warp7: Use PARTUUID to specify the rootfs locationFabio Estevam
warp7 can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the eMMC changes depending on the kernel version. In order to avoid such issue, use UUID method to specify the rootfs location. Succesfully tested booting a NXP 4.1 and also a mainline kernel. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06warp7: Modify fdt_file environment variableBreno Lima
Use imx7s-warp.dts as fdt_file because this is the name that upstream kernel will deploy. Signed-off-by: Breno Lima <breno.lima@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06warp7: Add PMIC supportVanessa Maegima
Add PMIC support. Tested by command "pmic PFUZE3000 dump". Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-07-28warp7: Move some USB configuration options to defconfigBreno Lima
Currently it's recommended to move some configuration options to the defconfig file. Move some USB related options to the defconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com>
2016-07-19mx7_common: Put display board info config into board fileStefan Agner
CONFIG_DISPLAY_BOARDINFO should not be placed in mx7_common because some boards might need a different config such as CONFIG_DISPLAY_BOARDINFO_LATE. Move it to the board file instead. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2016-07-19usb: move CONFIG_USB_EHCI_MX7 to KconfigStefan Agner
Create an entry for "config USB_EHCI_MX7" in Kconfig and switch over to it for all boards. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2016-06-18warp7: Fix DFU supportFabio Estevam
Currently DFU is not working. Adjust CONFIG_SYS_MALLOC_LEN and dfu_alt_info so that we are able to flash u-boot.imx into the eMMC via dfu using the following method: => dfu 0 mmc 0 In the host PC: dfu-util -D u-boot.imx -a boot This is the same approach done in the mx6sl warp board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18warp7: Fix watchdog resetMarco Franchi
The latest version of warp7 board provides the connection of the WDOG1_B pin to the PMIC. Program the watchdog to enable the WDOG1_B output which causes a POR reset. Based on the imx7dsabresd code. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-09common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig optionHeiko Schocher
move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-04-25configs: Re-sync with cmd/KconfigTom Rini
Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25include/configs: Whitespace fixupTom Rini
A number of moveconfig.py runs have left a instances of multiple empty lines in a row. Correct this to a single empty line. Signed-off-by: Tom Rini <trini@konsulko.com>