| Age | Commit message (Collapse) | Author |
|---|
|
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
Remove fsloadcmd / ext2load as we are using load command
which use the corresponding latest file system command.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
socfpga_dw_mmc driver will obtain the drvsel and
smplsel value from device tree instead of definition
in config header file.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
This board was constantly parasiting on the CV SoCDK, so split it
into it's own separate directory. Moreover, the board config was
missing important bits, like simple-bus support in SPL, the DRAM
configuration was incorrect and the DTS was also missing the pre
reloc bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Jan Viktorin <viktorin@rehivetech.com>
|
|
When adding support for the Arria10 platform, we're going to name the file
base_addr_a10.h, so to be systematic about it, rename the socfpga_base_addr.h
to be base_addr_ac5.h for the Arria5 and Cyclone5 platform.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
This patch add ZyXEL NSA310S 1-Bay Media Server
The ZyXEL NSA310S device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1000Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 4 Status LED (green)
- 1 Copy/Sync button
- 1 Reset button
- 1 SATA II port
- 2 USB 2.0 ports (front and back)
- Smart fan
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
|
|
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add MMC and SPI DFU support.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.
Add SPL support so that all the variants can be supported
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Tested basic fastboot commands, such as:
On the U-boot prompt:
=> fastboot 0
On the host PC:
$ fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2015.10-rc2-09654-g8f41d27
finished. total time: 0.000s
$ fastboot reboot -i 0x0525 --> board reboots fine.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Congatec boards boot from SPI NOR, so it makes more sense to use
SPI NOR to store the environment variables.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add SPI NOR support:
=> sf probe
SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Using 50 MiB malloc pool in SPL is nonsense. Since the caches are not
enabled in SPL, it takes 2 seconds to init the pool and has no obvious
benefit. Reduce the size to 1 MiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The DFU protocol implementation in U-Boot is much faster than the
FEL protocol implementation in the boot ROM on Allwinner devices.
Using DFU instead of FEL improves the USB transfer speed from
500-900 KB/s to 3.2-3.7 MB/s. This is particularly useful for
reducing the time needed for booting systems with large initrd
images.
FEL is still useful for loading the U-Boot bootloader and a boot
script, which may then activate DFU in the following way:
setenv dfu_alt_info ${dfu_alt_info_ram}
dfu 0 ram 0
bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}
The rest of the files can be transferred to the device using the
"dfu-util" tool.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add support for storing the environment in CFI NOR flash on Juno and FVP
models.
I also removed some config values that are not used by CFI flash parts.
Juno has 1 flash part with 259 sectors. The first 255 sectors are
0x40000 (256kb) and are followed by 4 sectors of 0x10000 (64KB).
FVP models simulate a 64MB NOR flash part at base address 0x0FFC0000.
This part has 256 x 256kb sectors. We use the last sector to store the
environment.
To save the NOR flash to a file, the following parameters should be
passed to the model:
-C bp.flashloader1.fname=${FILENAME}
-C bp.flashloader1.fnameWrite=${FILENAME}
Foundation models don't simulate the NOR flash, but having NOR support
in the u-boot binary does not harm: attempting to write to the NOR will
fail gracefully.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch allows vexpress64 targets to be compiled when
CONFIG_SYS_FLASH_CFI is enabled.
I considered using #warning instead of #error, but this just clutters up
the build output and hides real warnings.
Without this patch, you see errors during compilation like this:
include/configs/vexpress_aemv8a.h:42:2: error: #error "Unknown board
variant"
#error "Unknown board variant"
include/configs/vexpress_aemv8a.h:115:2: error: #error "Unknown board
variant"
#error "Unknown board variant"
include/configs/vexpress_aemv8a.h:280:2: error: #error "Unknown board
variant"
#error "Unknown board variant"
make[1]: *** [tools/envcrc.o] Error 1
make: *** [tools] Error 2
In file included from include/config.h:5:0,
from tools/envcrc.c:19:
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch makes the 2nd DRAM bank available on Juno only and not on
other vexpress64 targets, eg. the FVP models.
The commit below added a 2nd bank of NOR flash for Juno, but also for
all vexpress64 targets:
commit 2d0cee1ca2b9d977fa3214896bb2e30cfec77059
Author: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Date: Mon Oct 19 11:08:31 2015 +0100
vexpress64: Juno: Declare all 8GB of RAM and make them visible to the kernel.
Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
Declare a secondary memory bank and set the sizes correctly.
Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Unfortunately, I only fully tested on Juno R0, R1 and the FVP Foundation
model. Whilst FVP Base AEMV8 models run U-Boot OK, they fail to boot
the kernel.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This option only complicates the code unnecessarily, just use
CONFIG_SYS_DEF_EEPROM_ADDR as the default address if there are
only five arguments to eeprom {read/write} if this is defined.
If CONFIG_SYS_DEF_EEPROM_ADDR is not defined, we mandate all
six arguments.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
The NOR flash on Keystone 2 evms has a u-boot-spl partition size of
0x80000.
Currently burn_uboot_spi will erase 0x100000 from the spi NOR which will
cause a partial erase of the misc partition.
Fix this by correcting the erase size.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
|
|
Change to ns16550 uart for 10m50 devboard based on a new
Altera release.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Unify serial_tegra, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Unify serial_dw, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Unify serial_keystone, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Enable the USB keyboard on sandbox, now that we have a suitable emulation
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Allow console recording so that tests can use it. Also allow the console
output to be suppressed, to reduce test output 'noise'.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert to use driver model keyboard on QEMU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Convert to use driver model keyboard on Intel Crown Bay.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This option is mentioned but does not do anything. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
CONFIG_CONSOLE_CURSOR, CONFIG_SYS_CONSOLE_BLINK_COUNT and
CONFIG_CONSOLE_TIME are not used by any board. The implementation is not
great and stands in the way of a refactor of i8042. Drop these for now.
They can be re-introduced quite easily later, perhaps with driver-model
real-time-clock (RTC) support.
When reintroducing, it might be useful to make a few changes:
- Blink time would be more useful than blink count
- The confusing #ifdefs should be avoided
- The time functions should support driver model
- It would be best keyed off console_tstc() or some similar idle loop
rather than a particular input driver (i8042 in this case)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
zc1571 with silicon can operate on 200MHz maximum frequency. Setup this
frequency by default and fix setting for ep108.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable TI phy for Xilinx ZynqMP platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
OF_CONTROL is enabled by default for all Zynq boards.
The difference between two boot images is done by OF_SEPARATE
or OF_EMBED macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This board uses the same CPU (8309) as VECT1. The memory however is
different since it has NAND Flash, the NOR Flash partitioning is
different and of course the FPGAs as well.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
|
|
It should be after the u-boot reserved sectors and before the env
sectors, since the solution used for kmvect1 (tell the linker to put the
firmware into the u-boot produced binary, at the end of the area) should
be the exception.
The #define is only "conditional" so that we can still support kmvect1.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
The hardcoded value are bad, since the address could change between
different boards.
Furthermore, the relevant #defines are set only if #undefined here, so
that they can be changed by some boards if required.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
The ODT parameters for km8360 set the ODT_WR_ACS bit in u-boot KM-2011.09
that is used in the release bootpackage for kmcoge5ne. During the
transition from the kmeter1 to km8360 this was changed to
ODT_RD_ONLY_CURRENT, which is uncorrect and causes faulty RAM accesses at
low temperatures.
This is now changed to ODT_WR_ONLY_CURRENT which is the equivalent of
ODT_WR_ACS.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
