summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2018-06-18display5: config: Add GPT verification and restoration code on SWUpdate entryLukasz Majewski
If GPT gets broken, then after N boot attempts we will run the SWUpdate restoration image. On its enter we will check GPT and restore it if needed. To test it: display5 > mmc write 0x12000000 4 8 It will overwrite the primary GPT table. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Reduce rootfs2 (BACKUP) size from 1528M to 512MLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Add cma=256M to command line argumentsLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Update swupdate initramfs file name (now supporting ext4)Lukasz Majewski
After moving to swupdate 2017.07, the default fs for swupdate rootfs is ext4, not ext3. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: factory: Update BACKUP rootfs in factory modeLukasz Majewski
After splitting rootfs images to BACKUP and ACTIVE, the "factory" u-boot also needs to update the former. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Provide 'tftp_mmc_rootfs_bkp' command to write BACKUP rootfsLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: wdt: Enable WDT support (both SPL and u-boot)Lukasz Majewski
Test case: The fitImage gets corrupted: truncate -c -s 3M fitImage run tftp_mmc_fitImg setenv boot_os y reset [board shall hang in SPL with "Trying to boot from MMC1" information] Then after X seconds WDT is causing board to reset. After N boot attempts we enter recovery mode. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: Support for the emergency PAD pressingLukasz Majewski
To enter the special mode, one needs to short cut two pads with e.g. screw driver. After power up the SPL will execute u-boot in which proper actions will be taken. It is worth noting that we do not alter envs (even the BOOT_FROM variable) and unconditionally go to recovery. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Update SPI-NOR partition for larger swupdate-initramfsLukasz Majewski
The SPI-NOR partition information has been updated to store swupdate-kernel-FIT just after envs as well as two times larger swupdate-initramfs image. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Remove support for Linux initramfs recovery image bootLukasz Majewski
This is a prerequisite patch to combine SWUpdate and Linux recovery initramfs images. It removes the support for it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Reset the board when bootm failsLukasz Majewski
Since display5 is now supporting boot counting, we can just reset the board when bootm fails (i.e. it doesn't boot the fitImage kernel for any reason). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Provide command to flash the whole SPI-NOR memoryLukasz Majewski
It may be necessary to update the content of the whole SPI-NOR memory at once with using a single command (tftp_sf_img). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: Add "factory" (1MiB) SPI-NOR partition in u-bootLukasz Majewski
To test if this partition is present - one needs to write: display5 > sf probe; mtdparts display5 > sf erase factory +0x100000 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: config: factory: Setup IP config data according to LEG production ↵Lukasz Majewski
setup Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: factory: Add support for BOOT_FROM = FACTORY switchLukasz Majewski
When BOOT_FROM = FACTORY, then the LEG's factory setup is performed. This code relies on boot_nfs u-boot command, so it shall be adjusted appropriately (e.g. provide proper fitImage file). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-15Merge tag 'arc-updates-for-2018.07-rc2' of git://git.denx.de/u-boot-arcTom Rini
Here we just add a tool for HSDK flashable images preparation together with extensive documentation for HSDK board. This will help real-life users to update U-Boot on the board.
2018-06-15ARC: HSDK: Add tool and make target to generate bspEugeniy Paltsev
HSDK board has preloader that reads SPI flash pages and searches for a special image header to fetch and load binary. Add tool, make target (bsp-generate) to generate update script and u-boot binary image with header for preloader. Also add script to default environment to apply updates. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-06-15arm64: zynqmp: Enable SPD ddr support for zcu102 targetsMichal Simek
zcu102 contains DIMM with SPD on it at 0x51 address. For example: i2c dev 13 i2c sdram 51 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-13u-boot: Fix several typosShyam Saini
's/environemnt/environment/' and 's/Environemnt/Environment/' Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
2018-06-12configs: pcm051: Use am335x-wega-rdk.dtb as fdtfileMatwey V. Kornilov
In upstream Linux kernel, the fdtfile for this specific board is called am335x-wega-rdk.dtb Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12configs: pcm051: Use DEFAULT_LINUX_BOOT_ENV instead of hardcoded valuesMatwey V. Kornilov
It appears that DEFAULT_LINUX_BOOT_ENV can be used to boot pcm051 board. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12configs: pcm051: Use DEFAULT_MMC_TI_ARGS instead of hardcoded duplicatesMatwey V. Kornilov
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12configs: pcm051: Support distro bootcmdsMatwey V. Kornilov
Add support for distro bootcmds. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2018-06-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-06-12arm: mvebu: Add Helios4 Armada 38x initial supportDennis Gilmore
The helios4 is built on the SolidRun Armada 38x SOM. The port os based on the ClearFog board, using information from https://github.com/helios-4/u-boot-marvell as well as dtb input from https://github.com/helios-4/linux-marvell Signed-off-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11board: ls1012a: FRWY-LS1012A board supportBhaskar Upadhaya
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> [yorks: rebase and fix SPDX tag] [yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08arm: ls1021aqds: config: enable CONFIG_ID_EEPROM for mac commandJagdish Gediya
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-05board: STiH410-B2260: Add pxefile_addr_r variableRiku Voipio
Reading doc/README.distro , we see platform needs to set pxefile_addr_r to support distro boot. Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
2018-06-05ARM: legoev3: update boot script to load uEnv.txt and .dtbDavid Lechner
This updates the LEGO MINDSTORMS EV3 boot script to try loading a uEnv.txt file and a da850-lego-ev3.dtb device tree during boot. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: remove unused configuration optionsDavid Lechner
This removes the unused clock and RAM config options that were cargo- culted when this board was copied from the DA850 EVM. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: disable networkingDavid Lechner
This disables networking related items in the config. The EV3 does not have any networking hardware, so this is wasted space. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: increase flash image sizesDavid Lechner
This increases the kernel image to 4M and the rootfs image to 10M. It is getting hard to get a kernel image to fit in 3M. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: kirkwood: Enforce size limit for guruplugChris Packham
The u-boot binary sits in flash immediately before the environment. Don't allow the binary size to grow into the environment space. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05ARM: kirkwood: Enforce size limit for sheevaplugChris Packham
The u-boot binary sits in flash immediately before the environment. Don't allow the binary size to grow into the environment space. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05ARM: kirkwood: SBx81LIFKW: Enable network hardwareChris Packham
The SBx81LIFKW boards connect to the internal chassis management network via a Marvell 88e6097 L2 switch. The chassis connections are direct serdes on ports 8 and 9 with a RGMII interface on port 10 connected to the CPU MAC. For debugging purposes ports 0 and 1 are also taken out to headers on the board. Because the debug interfaces are sometimes connected to with straight ribbon cables we need to run them at 10Mbps. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05ARM: add SBx81LIFKW boardChris Packham
This is a series of line cards for Allied Telesis's SBx8100 chassis switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16 and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05arm: mvebu: switch clearfog to use device-tree i2c and gpioJon Nettleton
This switches the clearfog boards to use DM based gpio and i2c drivers. The io expanders are configured via their device-tree entries. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: add DT i2c aliases] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05arm: mvebu: enable sata support for clearfogJon Nettleton
The a38x sata interfaces run in ahci mode and can be accessed via the scsi command. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: rebase on current upstream] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-04Inherit default value for bootdelay from distro_bootcmd on odroid-xu3.Vagrant Cascadian
The default value with distro_bootcmd is 2 seconds, which is reasonably fast, and provides a consistent experience across platforms supporting distro_bootcmd. The current bootdelay value of 0 seconds is a bit challenging to interrupt when desired. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Marek Vasut <marex@denx.de>
2018-06-03rpi: Fix fdt_high & initrd_high for 64-bit buildsTuomas Tynkkynen
The magic value that disables relocation is dependent on the CPU word size, so the current 'ffffffff' is doing the wrong thing on aarch64. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-06-02Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-06-01Merge tag 'xilinx-for-v2018.07-2' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.07 second pull zynqmp: - Show reset reason - Remove emulation platform - Update pmufw version - Simplify mmc bootmode - Remove dc2 useless configuration file - Cleanup mini config - Defconfig syncup - zcu100, zcu104 and zcu111 dts fixes xilinx: - Use live-tree functions in some drivers - Add support for Avnet Minized and Antminer S9 fpga: - Add secure bitstream loading support mmc: - Add hs200 mode support usb xhci: - Header fix
2018-06-01ARM: renesas: Add R8A77990 E3 Ebisu boardMarek Vasut
Add support for the R8A77990 Ebisu board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-01ARM: rmobile: Enable MTD partitioning on Gen2 with SFMarek Vasut
Enable MTD partitioning support on Gen2 boards with SPI NORs. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-31Merge tag 'arc-updates-for-2018.07-rc1' of git://git.denx.de/u-boot-arcTom Rini
Here we do a couple of minor fixes like: - Move .ivt section to the very beginning of the image by default which allows us to use that image put right at reset vector (usually 0x0) - Improve relocation fix-up which became required once we moved .ivt and understood a problem with existing implementation where we relied on a particular placement of sections. Now we don't care about placement because we just explicitly check for .text and in case of ARCompact .ivt sections - Re-implemnt do_reset() such that it calls reset_cpu() which could implmented for a particular board And hte most important part we introduce support for yet another devboard from Synopsys - EMDK.
2018-05-31ARC: Add support for EM Development Kit boardAlexey Brodkin
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is an FPGA-based development platform from Synopsys aimed to speed-up development of software for ARC EM cores and entire subsystems based on ARC EM like Data Fusion, Secure and Sensor & Control subsystems. U-Boot is supposed to be used as a primary bootloader on EMDK allowing users to easily load and start their application from micro-SD card. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-05-31arm: zynq: Add support for Bitmain Antminer S9 control boardEzequiel Garcia
This is control board on Bitmain Antminer S9. There are 3 board variables with 256MB, 512MB and 1024MB DDR. DDR memory is automatically detected with using get_with using get_ram_size(). Bitmain is using 16MB space for FPGA which is handled via reserved-memory. Also U-Boot is allocating 16B for storing bootcounts. Watchdog is started but never service in U-Boot. SPL MMC is working. SPL NAND is not working because it is not supported as of now. Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Remove CMD_UNZIP for mini configurationMichal Simek
CMD_UNZIP is already disabled via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Remove empty configuration fileMichal Simek
There is no reason to keep empty config file in the tree that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2024-12-24 01:41:42 +0000