summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2017-12-06armv8: LS1088A_QSPI: SECURE_BOOT: Images validationUdit Agarwal
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC phase using esbc_validate command. Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment Add header address for PPA to be validated during ESBC phase for LS1088A platform based on LAyerscape Chasis 3. Moves sec_init prior to ppa_init as for validation of PPA sec must be initialised before the PPA is initialised. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06armv8: ls1012a: Modify Kernel and Environment offsetBhaskar Upadhaya
Kernel is now located at 0x1000000 instead of 0xa00000 and envirorment variables are located at 3MB offset instead of 2MB in Flash. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06powerpc/p1_p2_rdb_pc: Fix endian access issue on EHCI intinalizationRan Wang
This issue is exposed after commit 9000eddbae0d ("drivers/usb/ehci: Use platform-specific accessors"), the wrong endianness of EHCI controller programing will cause USB function down. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06powerpc/T104xRDB: Fix endian access issue on EHCI intinalizationRan Wang
This issue is exposed after commit 9000eddbae0d ("drivers/usb/ehci: Use platform-specific accessors"), the wrong endianness of EHCI controller programing will cause USB function down. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-04omap3: evm: Explicitly use DISTRO_DEFAULTS features at startupDerald D. Woods
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot [fallback 1] Check MMC 0:1 zImage and run mmcbootz [fallback 2] Check MMC 0:1 uImage and run mmcboot [fallback 3] Check NAND partitions and run nandboot If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is followed. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2017-12-04ARM: arch-meson: build memory banks using reported memory from registersNeil Armstrong
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-04arm: Add Khadas VIM support based on Meson GXL familyNeil Armstrong
This adds platform code for the Khadas VIM board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission supports UART, MMC/SDCard and Ethernet with the Internal RMII PHY. The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13 stable tree as of 4.13.8. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04arm: Add LibreTech CC support based on Meson GXL familyNeil Armstrong
This adds platform code for the Libre Computer CC "Le Potato" board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission supports UART, MMC/SDCard and Ethernet with the Internal RMII PHY. The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13 stable tree as of 4.13.8. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04add support for Raspberry Pi Zero WDmitry Korunov
Signed-off-by: Dmitry Korunov <dessel.k@gmail.com>
2017-11-30rockchip: rk3128: add evb-rk3128 supportKever Yang
evb-rk3128 is an evb from Rockchip based on rk3128 SoC: - 2 USB2.0 Host port; - 1 HDMI port; - 2 10/100M eth port; - 2GB ddr; - 16GB eMMC; - UART to USB debug port; Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30rockchip: rk3128: add soc basic supportKever Yang
RK3128 is a SoC from Rockchip with quad-core Cortex-A7 CPU and mali400 GPU. Support Nand flash, eMMC, SD card, USB 2.0 host and device, HDMI/LVDS/MIPI display. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2017-11-30Merge git://git.denx.de/u-boot-marvellTom Rini
2017-11-30ARM: rmobile: Rework the ULCB CPLD driverMarek Vasut
Rework the ULCB CPLD driver and make it into a sysreset driver, since that is what the ULCB CPLD driver is mostly for. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30arm64: mvebu: armada-7k/8k: drop useless #ifdefBaruch Siach
CONFIG_ENV_IS_IN_NAND has been removed in commit 2be296538e2e (Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig). CONFIG_ENV_IS_IN_SPI_FLASH has been removed in commit 91c868fe7cd (Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig). The environment #ifdef is now empty. Remove it. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-29board: laird: add WB50N CPU moduleBen Whitten
This board is based on the Atmel sama5d3 eval boards. Supporting the following features: - Boot from NAND Flash - Ethernet - FIT - SPL Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com> Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
2017-11-29board: laird: add WB45N CPU moduleBen Whitten
This board is based on the Atmel 9x5 eval board. Supporting the following features: - Boot from NAND Flash - Ethernet - FIT - SPL Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com> Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
2017-11-29board: atmel: add sama5d2_ptc_ek boardLudovic Desroches
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board which was a prototype. Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-11-30nds32: board: Support ftsdc010 DM.Rick Chen
AG101P/AE3XX enable ftsdc010 dm flow. Signed-off-by: Rick Chen <rick@andestech.com>
2017-11-30ARM: rmobile: Migrate boards to RCar IIC driversMarek Vasut
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC driver instead. The SH I2C driver should be deprecated and removed eventually. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Remove SCIF configsMarek Vasut
Since we use DM and DT, these SCIF configuration options are useless. Remove them. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Clean up ad-hoc clock macrosMarek Vasut
As we have a proper clock framework driver, these macros are not needed, so drop them and clean up the whitelist. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Zap ad-hoc DRAM configuration macrosMarek Vasut
These macros are no longer needed since the DRAM configuration is parsed from the DT. Drop them all. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Zap rmobile_sysinfo on Gen3Marek Vasut
Since checkboard() is gone, rmobile_sysinfo is also pointless on Gen3. Furthermore, nuke ad-hoc CONFIG_RCAR_BOARD_STRING which is also dead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Stop using rcar-common/common.c on Gen3Marek Vasut
Since the Gen3 clock driver now has a .remove callback, it is no longer necessary to shut the clock down before booting Linux in the arch_preboot_os hook. Stop using it and while doing so, remove all the ad-hoc config options which this hook used. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Clean up GIC macrosMarek Vasut
Pull out the GIC macros from the board configuration files into the common Gen3 configuration file since these macros are the same for all Gen3 systems. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Drop CONFIG_USB_MAX_CONTROLLER_COUNT on Gen3 boardsMarek Vasut
The USB support has been switched to DM, so this macro is no longer meaningful, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30ARM: rmobile: Enable Micrel KSZ90x1 PHY driver on ULCBMarek Vasut
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated with KSZ9031 and without this driver, the PHY cannot be operated. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-29Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.1 Zynq: - Add support for Syzygy and cc108 boards - Add support for mini u-boot configurations (cse) - dts updates - config/defconfig updates in connection to Kconfig changes - Fix psu_init handling ZynqMP: - SPL fixes - Remove slcr.c - Fixing r5 startup sequence - Add support for external pmufw - Add support for new ZynqMP chips - dts updates - Add support for zcu102 rev1.0 board Drivers: - nand: Support external timing setting and board init - ahci: Fix wording - axi_emac: Wait for bit, non processor mode, readl/write conversion - zynq_gem: Fix SGMII/PCS support
2017-11-29arm: zynq: Do not show information from checkboard twiceMichal Simek
There is no reason to show information about board twice. Remove boardinfo late calls. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28Merge git://git.denx.de/u-boot-mipsTom Rini
2017-11-28boston: Set CONFIG_SYS_LOAD_ADDR to 0x88000000Paul Burton
Generally we load Linux kernels on Boston boards in the form of FIT images containing a compressed kernel binary. Linux is linked at 0x80100000 and so we need to decompress the kernel binary to that address, however this is our default load address which means that unless explicitly avoided we hit a decompression error as the uncompressed kernel binary overwrites its compressed version from the FIT image. Avoid this by adjusting CONFIG_SYS_LOAD_ADDR to 0x88000000 (or 0xffffffff88000000 for MIPS64 builds) which avoids the address overlap between compressed & uncompressed kernel binaries. Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: u-boot@lists.denx.de
2017-11-29ARM: uniphier: remove unused NAND CONFIG optionsMasahiro Yamada
The Denali NAND driver does not use these options any more. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-28arm: zynq: Add mini u-boot configuration for zynqMichal Simek
Add configuration files/dtses for mini u-boot configurations which runs out of OCM. ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE 0xfffc0000 +#define CONFIG_SYS_SDRAM_SIZE 0x40000 was hardcoded. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28arm: zynq: Move ZYNQ_SERIAL to KconfigMichal Simek
Move cadence/zynq serial driver via Kconfig Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28arm: zynq: Enable FPGA/FPGA_XILINX via KconfigMichal Simek
Enabling fpga via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28arm: zynq: Remove empty ifdef env structures from config fileMichal Simek
All these configs were moved to Kconfig that's why this empty ifdef structure is not needed anymore. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28arm: zynq: Add support for SYZYGY Hub boardTom McLeod
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-27Merge git://www.denx.de/git/u-boot-imxTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27i.MX6UL: icore: Add SPL_OF_CONTROL supportJagan Teki
Add OF_CONTROL support for SPL code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27i.MX6Q: icore: Add SPL_OF_CONTROL supportJagan Teki
Add OF_CONTROL support for SPL code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27mx6sxsabresd: Use PARTUUID to specify the rootfs locationFabio Estevam
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the SD card changes depending on the kernel version. In order to avoid such issue, use the UUID method to specify the rootfs location. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-11-21rockchip: remove duplicate CONFIG_ENV_SIZE definitionsPhilipp Tomsich
A few header files still have a definition of CONFIG_ENV_SIZE, causing warnings during buildman runs. This removes the duplicate definitions from evb_px5.h, geekbox.h and rv1108_common.h. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21rockchip: rk3188: move CONFIG_SPL_* entries from rk3188_common.h to KconfigPhilipp Tomsich
There still are a few CONFIG_SPL_* options selected using defines from rk3188_common.h instead of via Kconfig. This migrates those over to Kconfig. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21rockchip: rk3188: use boot0 hook to load up SPL in 2 stepsPhilipp Tomsich
For the RK3188, the BROM will attempt to load up the first stage image (SPL for the RK3188) in two steps: first 1KB to offset 0x800 in the SRAM and then the remainder to offset 0xc00 in the SRAM. It always enters at 0x804, though. With this changeset, the RK3188 boot removes the TPL (stub) stage and builds a single SPL binary that utilizes the early back-to-bootrom via the boot0-hook. Consequently, the passing of the saved boot params via pmu->os_reg[2] is also removed. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21rockchip: rk3036: use aligned address for SPL_TEXT_BASEPhilipp Tomsich
With the boot0-hook inserting the additional padding to receive our SPL magic, the SPL_TEXT_BASE can be aligned again. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21rockchip: rk3288: use aligned address for SPL_TEXT_BASEKever Yang
After we use boot0 hook, we can use offset '000' instead of '004' as SPL_TEXT_BASE. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> [Updated tag in commit summary:] Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-20dra7x: fastboot: Increase recovery partition sizePraneeth Bajjuri
As per current android recommendation https://source.android.com/devices/architecture/kernel/modular-kernels 1. Android recovery mode should contain both SOC and ODM kernel modules in the recovery partition. 2. If a kernel module is required both in recovery and normal boot mode, the module has to be located in recovery and vendor partition seperately. 3. Kernel modules used in recovery mode should be independent of vendor and odm partition 4. Recovery image should contain atleast storage, display, keypad, battery and pmic modules. Due to these requirements, recovery image size has increased to >10MB. This patch is to increase recovery partition size for TI devices so that we dont see such flashing error log: sending 'recovery' (12560 KB)... OKAY [ 0.436s] writing 'recovery'... FAILED (remote: too large for partition) finished. total time: 0.458s Signed-off-by: Praneeth Bajjuri <praneeth@ti.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-11-20mx53: Add Board support for GE PPDPeter Senna Tschudin
Create board support for GE PPD, based on mx53loco. Use mx53ppd_defconfig make target to configure for this board. Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20pico-imx6ul: Use FS_GENERIC load commandFabio Berton
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit (git 2.34.1) at 2025-01-13 14:07:53 +0000