summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2018-01-03ARM: imx: cm_fx6: env: support distro boot commandChristopher Spinrath
The current default environment of the cm_fx6 is not suitable for booting modern distributions. Instead of extending the custom environment, let's use the distro boot command, which has been developed for precisely this use case. If the distro boot command fails, fall back to the old behavior (except for USB drives where the old behaviour is completely covered by the distro boot command). That way it is still possible to create "rescue SD cards" for old installations (e.g. if one messes up the on-flash environment). Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-03ARM: imx: cm_fx6: env: use standard variablesChristopher Spinrath
In preparation for supporting the distro boot command, introduce the standard variables for specifying load addresses, which are documented in README and doc/README.distro, and replace the custom variables used so far with them. Since the current address layout disregards an address for an initramfs, also switch to the load addresses used and proven by other imx6 boards (e.g. the wandboard and nitrogen6x), instead of going on with our own way. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-03mx6: Add board mx6memcal for use in validating DDREric Nelson
This is a virtual "board" that uses configuration files and Kconfig to define the memory layout used by a real board during the board bring-up process. It generates an SPL image that can be loaded using imx_usb or SB_LOADER.exe. When run, it will generate a set of calibration constants for use in either or both a DCD configuration file for boards that use u-boot.imx or struct mx6_mmdc_calibration for boards that boot via SPL. In essence, it is a configurable, open-source variant of the Freescale ddr-stress tool. https://community.nxp.com/docs/DOC-105652 File mx6memcal_defconfig configures the board for use with mx6sabresd or mx6qsabreauto. Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-01ARM: dts: omap3-evm: Enable DM and devicetree for TMDSEVM{3530, 3730}Derald D. Woods
This commit updates the configuration files needed to support OF_CONTROL on the OMAP3 EVM baseboard. Additionally: - CONFIG_SYS_THUMB_BUILD is enabled - CONFIG_SPL_ENV_SUPPORT is enabled Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb]. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-01-01ARM: omap3: evm: Do not relocate FDT addressDerald D. Woods
This commit keeps the 'fdtaddr' as provided by DEFAULT_LINUX_BOOT_ENV. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2017-12-29Merge git://git.denx.de/u-boot-imxTom Rini
2017-12-29mx6sxsabresd: Load the correct dtb for revA boardFabio Estevam
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the correct dtb is imx6sx-sdb-reva.dtb, so make this possible. While at it, remove an extra 'mmc dev'. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-29mx6_common: remove dead codeAdam Ford
There is an #ifdef and #endif with nothing in between. This patch simply removes this dead/useless code. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-27Merge git://git.denx.de/u-boot-dmTom Rini
2017-12-26Move CONFIG_PANIC_HANG to KconfigMasahiro Yamada
Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-24boards: ls1046ardb: disable unavailable "ethernet" node in dtsPrabhakar Kushwaha
Linux device tree contains "ethernet" node for all possible interface supported by SoC i.e. LS1046A. It is not necessary for a SerDes protocol to support all possible interface. So disable unavailable "ethernet" node in device tree. Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address sequentially from environment variables Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-19Merge git://git.denx.de/u-boot-sunxiTom Rini
2017-12-19sunxi: arm64: Increase CONFIG_SYS_BOOTM_LEN to 32MBJagan Teki
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error when uncompressing Image.gz out of FIT image. Uncompressing Kernel Image ... Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN and loading Image out of FIT image. Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN Must RESET board to recover Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-12-18Merge git://git.denx.de/u-boot-rockchipTom Rini
2017-12-18Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-12-18am335x_evm: Fix DFU for eMMCSam Protsenko
Use dfu_alt_info_emmc variable from include/environment/ti/dfu.h file. It was probably overlooked when extracting DFU variables to mentioned file. This patch fixes DFU on BeagleBone Black, so that we can use commands like ones below to upgrade various images on eMMC: => setenv dfu_alt_info $dfu_alt_info_emmc => dfu 0 mmc 1 $ dfu-util -D MLO -a MLO.raw $ dfu-util -D u-boot.img -a u-boot.img.raw Without this patch, the user is forced to assign the value to dfu_alt_info_emmc manually, which contradicts with instructions [1]. [1] http://processors.wiki.ti.com/index.php/Linux_Core_U-Boot_User%27s_Guide Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-12-18Merge tag 'xilinx-for-v2018.01-rc2-v2' of ↵Tom Rini
git://www.denx.de/git/u-boot-microblaze Xilinx changes for v2018.01-rc2-v2 fpga: - Enable loading bitstream via fit image for !xilinx platforms zynq: - Fix SPL SD boot mode zynqmp: - Not not reset in panic - Do not use simple allocator because of fat changes - Various dt chagnes - modeboot variable setup - Fix fpga loading on automotive devices - Fix coverity issues test: - Fix env test for !hush case - Stephen's patch
2017-12-18armv8: ls1046aqds: Adjust IFC timing for NOR flashYork Sun
Increase setup, assertion and hold time related to chip-select signal. Additional delay is needed for the signal to propogate through FPGA. This adjustment slightly increase the read and write cycle but has no impact on burst read or write. Signed-off-by: York Sun <york.sun@nxp.com>
2017-12-18armv8: ls2080a: Increase load image len for NAND bootYork Sun
Again the image size increases and the length needs to be adjusted. Signed-off-by: York Sun <york.sun@nxp.com>
2017-12-18rockchip: move CONFIG_ENV_SIZE and CONFIG_ENV_OFFSET to KconfigKlaus Goger
This commit adds ENV_SIZE and ENV_OFFSET configuration items for ARCH_ROCKCHIP, but keeps these non-visible (i.e. not prompt is given). With these new items present, the configuration from the header files is moved to Kconfig. Keeping these non-visible is necessary to have the possibility to select new default values if CONFIG_IS_IN_* is changed (interactively or with oldconfig). Otherwise it will always be set to a previous value if used with a prompt. As an example if we do a defconfig with CONFIG_IS_IN_MMC and change it to CONFIG_IS_IN_SPI_FLASH via menuconfig, ENV_SIZE and ENV_OFFSET will not be changed to the correct values as defconfig will already have set them to the default values of CONFIG_IS_IN_MMC in .config. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-17rockchip: config: update part tableKever Yang
User do not need to access the reserved part in system, remove them from partition table. Rename atf to trust as generic name for armv7 do not use ATF. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-14armv8: ls1012ardb: add more board version informationYangbo Lu
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and detect it when u-boot starts up. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-14armv8: ls1012ardb: clean up definitions for I2C IO expandersYangbo Lu
This patch is to clean up definitions for I2C IO expanders. The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2. Fixed it in this patch. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-14arm64: zynqmp: Add support for generic QSPI bootMichal Simek
This patch is enabling support for SPL QSPI boot. First of all it is necessary to generate atf-spi.ub which is different format than atf-uboot.ub (this can be made as legacy image too) ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'` aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin ./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin atf-uboot.ub ./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR -n "atf-for-qspi" -E -d bl31.bin atf-spi.ub This patch is using this QSPI layout with offsets: 0 boot.bin 512k atf-ub 640k u-boot.bin 1280k u-boot.img Which corresponding by writing these images(read from MMC) mmcinfo sf probe load mmc 0 10000000 boot.bin sf erase 0 +$filesize sf write 10000000 0 $filesize load mmc 0 10000000 atf-spi.ub sf erase 0x80000 +$filesize sf write 10000000 0x80000 $filesize load mmc 0 10000000 u-boot.bin sf erase 0xa0000 +$filesize sf write 10000000 0xa0000 $filesize load mmc 0 10000000 u-boot.img sf erase 0x140000 +$filesize sf write 10000000 0x140000 $filesize For testing u-boot running in EL3 you can break atf-spi.ub like this: sf probe sf erase 0x80000 +4 Then u-boot.img is executed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm64: zynqmp: Do not use SPL_SYS_MALLOC_SIMPLE allocatorMichal Simek
This was caused by: "fs/fat: Reduce stack usage" (sha1:2460098cffacd18729262e3ed36656e6943783ed) which converted fat code to use malloc. But simple malloc is not freeing space that's why full malloc implementation is needed. Malloc space is added to RAM. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm64: zynqmp: Do not perform reset in case of panicMichal Simek
Do not perform reset when panic happens because in the next reset panic happens again and logs are overflood by the same errors. This can be enabled by default and reset can be performed via watchdog. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-14arm: zynq: Fix SPL SD boot modeMichal Simek
This patch is fixing two issues: 1. Insufficient stack size for fat fs buffers 2. Insufficient space in malloc area Tested on zc702 and zc706. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-13Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2017-12-13Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2017-12-13arm64: ls1012afrdm: Add distro boot supportRajesh Bhagat
Include common config_distro_defaults.h and config_distro_bootcmd.h for u-boot enviroments to support automatical distro boot which scan boot.scr from external storage devices(e.g. SD and USB) and execute autoboot script. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-13arm64: ls1012ardb: Add distro boot supportRajesh Bhagat
Include common config_distro_defaults.h and config_distro_bootcmd.h for u-boot enviroments to support automatical distro boot which scan boot.scr from external storage devices(e.g. SD and USB) and execute autoboot script. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-13armv8: ls1088ardb: support force SDHC mode by hwconfigYangbo Lu
The BRDCFG5[SPISDHC] register field of Qixis device is used to control SPI and SDHC signal routing. 10 = Force SDHC Mode - SPI_CS[0] is routed to CPLD for SDHC_VS use. - SPI_CS[1] is unused. - SPI_CS[2:3] are routed to the TDMRiser slot. 11 = Force eMMC Mode - SPI_CS[0:3] are routed to the eMMC card. 0X = Auto Mode - If SDHC_CS_B=0 (SDHC card installed): Use SDHC mode described above. - Else SDHC_CS_B=1 (no SDHC card installed): Use eMMC mode described above. In default the hardware uses auto mode, but sometimes we need to use force SDHC mode to support SD card hotplug, or SD sleep waking up in kernel. This patch is to support force SDHC mode by hwconfig. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-12ARM: omap3_logic: Unlock NAND automatically in U-BootAdam Ford
The Micron Flash is locked by default. This will automaticlly unlock so manually unlocking is unnecessary in U-Boot. Signed-off-by: Adam Ford <aford173@gmail.com>
2017-12-12ata: Migrate CONFIG_MVSATA_IDE to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_LIBATA to KconfigTuomas Tynkkynen
This symbol enables some library code used by various SATA drivers, so make this a non-user-visible symbol select'ed by the respective drivers, and let moveconfig handle the rest. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_SCSI_AHCI to KconfigTuomas Tynkkynen
And use 'imply' liberally. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_DWC_AHSATA to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_FSL_SATA to KconfigTuomas Tynkkynen
Use 'imply' here liberally to avoid the combinatorial explosion of defconfig changes in the PowerPC boards. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_SATA_MV to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_SATA_SIL3114 to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12ata: Migrate CONFIG_SATA_SIL to KconfigTuomas Tynkkynen
Use 'imply' here liberally to avoid the combinatorial explosion of defconfig changes in the PowerPC boards. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-09ARM: socfpga: remove unneeded CONFIG_SYS_NAND_USE_FLASH_BBTMasahiro Yamada
Neither denali.c nor denali_spl.c references this option. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-09ARM: socfpga: remove unused CONFIG_NAND_DENALI_ECC_SIZEMasahiro Yamada
This option is no longer used. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-09ARM: rmobile: Add R8A77995 D3 Draak boardMarek Vasut
Add bits to support yet another board, the R8A77995 D3 Draak. The DT file is from Linux 4.15-rc1 , commit b35334447513c14a4dd55a67c269a743d4a4824b . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-12-09ARM: rmobile: Add R8A77970 V3M Eagle boardMarek Vasut
Add bits to support yet another board, the R8A77970 V3M Eagle. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-12-09ARM: rmobile: Add R8A77970 SoCMarek Vasut
Add bits to support yet another SoC, the R8A77970 V3M . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-12-08Merge git://git.denx.de/u-boot-mpc85xxTom Rini
2017-12-07sunxi: Add default partition schemeMaxime Ripard
The partitions variable is especially useful to create a partition table from U-Boot, either directly from the U-Boot shell, or through flashing tools like fastboot and its oem format command. This is especially useful on devices with an eMMC you can't take out to flash from another system, and booting a Linux system first to flash our system then is not really practical. Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-12-06armv8: ls1088a: Add nand support for ls1088ardbAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06SECURE BOOT: Add fall back optionVinitha Pillai-B57223
Add fall back option, to boot from NOR/QSPI/SD for LS1043, LS1046, LS1021 in case of distro boot failure. For LS1046, add kernel validation in case of secure boot in sd_bootcmd and qspi_bootcmd. For LS1043 and LS1021, add kernel validation in case of secure boot in sd_bootcmd, qspi_bootcmdand nor_bootcmd. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>