summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2019-10-13Add i.MX7D based Meerkat96 board supportShawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-11tao3530: Fix usage of mmc rescanJarkko Nikula
Currently "bootcmd" does not work as intended but instead prints MMC usage information and goes directly to "nandboot". Follow what the commit 669681104daa ("configs: Fix usage of mmc rescan") does for other boards prior to support for TechNexion TAO3530 SoM was added. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
2019-10-11configs: ti: Use addr_fit for run_fit environment variableAndrew F. Davis
When running 'run_fit' the FIT file should have been loaded at 'addr_fit', although at this point they should be the same use this variable instead of 'loadaddr'. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-10-11am335x, guardian: adapt guardian board to DMMoses Christopher
- update partition table - remove env partitions - dts: add new interfaces (uart2, extra gpio-key) remove unneeded entries update nand timings for performance improvement - defconfig: adapt configurations to suit DM remove unneeded configs - am335x_guardian.h: remove mmc boot Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11env: ti: am65x_evm: Add env support to boot the MCU R5F rprocsSuman Anna
Add support to boot the MCU domain R5F Core0 remoteproc at U-boot prompt on the AM65x EVM boards by using the 'boot_rprocs' and other env variables defined in the common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS' macro. The default configuration is to use the MCU R5F in Split mode, so both the R5F Core0 and Core1 are started before loading and booting the Linux kernel using the following firmware: MCU R5FSS0 Core0 (Split) : 0 /lib/firmware/am65x-mcu-r5f0_0-fw MCU R5FSS0 Core1 (Split) : 1 /lib/firmware/am65x-mcu-r5f0_1-fw The MCU R5FSS was initially running the R5 SPL in LockStep mode with ATCM disabled, and is actually shutdown to enable it to be reconfigured and booted by either A53 U-Boot or Linux kernel in remoteproc mode and using ATCM. The MCU R5FSS would need to be reconfigured for Lockstep mode through DT if a fault-tolerant/safety application were to be run on the cluster with the DEFAULT_RPROCS macro updated to remove the Core1 firmware. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11env: ti: j721e-evm: Add support to boot rprocs including R5Fs and DSPsSuman Anna
Add support to boot some remoteprocs at U-boot prompt on the J721E EVM boards by using the 'boot_rprocs' and other env variables defined in the common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS' macro. The list of R5F cores to be started before loading and booting the Linux kernel are as follows, and in this order: Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7-main-r5f0_1-fw Main R5FSS1 (LockStep) : 4 /lib/firmware/j7-main-r5f1_0-fw The MCU R5FSS0 and Main R5FSS1 are currently in LockStep mode, so the equivalent Core1 rprocs (rproc #1 and #5) are not included. The Main R5FSS0 Core0 (rproc #2) is already started by R5 SPL, so is not included in the list either. The DSP cores are started in the following order before loading and booting the Linux kernel: C66_0: 6 /lib/firmware/j7-c66_0-fw C66_1: 7 /lib/firmware/j7-c66_1-fw C71_0: 8 /lib/firmware/j7-c71_0-fw The order of the rprocs to boot can be changed at runtime if desired by overwriting the 'rproc_fw_binaries' environment variable at U-boot prompt. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-09ARM: socfpga: vining_fpga: Update environmentMarek Vasut
Update board environment to match the one used in deployment. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09ARM: socfpga: vining_fpga: Rename VINING|FPGAMarek Vasut
The company Samtec was merged into Softing, migrate the board over to the new name and update copyright headers. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09Merge tag 'xilinx-for-v2020.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
2019-10-09Merge tag 'u-boot-imx-20191009' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191009 ------------------- Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532 - MX6UL / ULZ - Toradex board - Allow to set OCRAM for MX6Q/D - MX7ULP - MX8: (container image, imx8mq_mek), SCU API - fix several board booting from SD/EMMC (cubox-i for example) - pico boards [trini: display5 merged manually] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Move WATCHDOG_TIMEOUT_MSECS to Kconfig (Heiko)
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Rename existing FSP code to fsp1 - Add fsp2 directory in preparation to support FSP 2.0 - Various x86 platform codes update - Various bug fixes and updates in dm core, sandbox and spl
2019-10-08pico-imx7d: fix splash logo drawingJoris Offouga
Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08apalis_imx6: use distroboot by defaultIgor Opaniuk
Use distro_bootcmd as default bootcmd instead of legacy wrappers. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-08colibri_imx6/imx7/imx8x: use distroboot by defaultIgor Opaniuk
Use distro_bootcmd as defauult bootcmd instead of legacy wrappers. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-08imx: Add i.MX8MM EVK board support.Peng Fan
Add board and SoC dts Add ddr training code support SD/MMC/GPIO/PINCTRL/UART Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: fix link issueAnatolij Gustschin
Since recent splash changes common code for splashscreen logo should be used instead of adding duplicated code under board directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations used old board specific logo code and do not link, fix them. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: wandboard: convert FEC support to DM_ETHAnatolij Gustschin
Remove CONFIG_DM_ETH conversion warning to avoid board removal. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08DM: WDT: Convert WDT driver to use DM/DTS (including SYSRESET)Lukasz Majewski
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover, the SYSRESET_WATCHDOG driver is used to support 'reset' command. As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is enabled for it. This allows the legacy SPL code to work properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)Lukasz Majewski
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: eth: Switch display5 board to use DM_ETHLukasz Majewski
After this commit the display5 device would use FEC driver supporting driver model (DM_ETH). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: I2C: Switch display5 board to use DM_I2CLukasz Majewski
After this commit the display5 device would use I2C driver supporting driver model (DM_I2C). The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize on-bus devices according to device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08pico-imx6: Add Falcon modeFabio Estevam
Add Falcon mode support, which allows the SPL to load and jump to the Linux kernel directly, without the need of loading U-Boot proper. CONFIG_SPL_OS_BOOT=y needs to be passed in the defconfig in order to use Falcon mode. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add splashscreen supportFabio Estevam
Add splashscreen support. Tested with the parallel FT5x06-WVGA panel. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add Ethernet supportFabio Estevam
Add Ethernet support. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Fix bootmenu handlingOtavio Salvador
We should use a common script to allow booting the U-Boot console as fallback so we ended using a 'default_boot' and 'base_boot' environment scripts to accomplish that. Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add initial supportFabio Estevam
Add the initial support for the pico-imx6 variants. DDR initialization is based on the TechNexion's U-Boot code. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08mx53loco: Fix U-Boot corruption after saving the environmentFabio Estevam
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: pico-imx7d: Convert to DM_VIDEOJoris Offouga
This commit convert all pico-imx7d to DM_VIDEO Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08pico-imx7d: Add NYMPH baseboard supportOtavio Salvador
This add the boot menu option for the NYMPH baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: Add DWARF baseboard supportOtavio Salvador
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Add LCD supportFabio Estevam
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Increase the CONFIG_ENV_OFFSET sizeFabio Estevam
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Add DWARF baseboard supportOtavio Salvador
This add the boot menu option for the DWARF baseboard as well as a specific config file for users which wish to use it as a pre-defined board. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08imx8qm: correct fdt_filePeng Fan
imx8qm-mek.dtb is the correct fdt file, not fsl-imx8qxp-mek.dtb Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: imx8qxp_mek: fix CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTORPeng Fan
The first stage of flash.bin is larger than 584 * 512, so when writting u-boot.itb, some data will be override. Enlarge the CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: configs: Cleanup CONFIG_SECURE_BOOT commentsBreno Matheus Lima
Since commit 6e1f4d2652e7 ("arm: imx-common: add SECURE_BOOT option to Kconfig") the SECURE_BOOT option is selected through Kconfig. Cleanup comments in code to align with this change. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08Kconfig: Migrate CONFIG_CSF_SIZE to KconfigBreno Matheus Lima
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000. mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08ARM: imx: Support larger SPL size on IMX6DQRobert Hancock
Previously the SPL size on all iMX6 platforms was restricted to 68KB because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the other iMX6 variants have 256KB of OCRAM. Add an option CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which don't need to support the SL/DL variants. This allows for an SPL size of 196KB, which makes it much easier to use configurations such as SPL with driver model and FDT control. Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
2019-10-08imx: mx6ul_14x14_evk: convert to DM_VIDEOPeng Fan
To support DM_VIDEO, Add display node for lcdif Drop board iomuxc settings. Enable DM_VIDEO Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: add i.MX6ULZ boardPeng Fan
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08microblaze: Setup reasonable maximum bootm lenMichal Simek
We are far from 8MB default size. Setup 64MB for now. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Enable cache by defaultMichal Simek
The whole cache code needs to be redesign to read information about cache from DT instead of macro selection. Enable caches by default because systems have caches on by default for Linux. Also enable CMD_CACHE to be able to disable cache if there is any issue. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Move CONFIG_LMB from board file to config.hMichal Simek
It is common for the whole architecture that's why move it there. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08configs: apalis-tk1: Do not define CONFIG_SYS_BOOT_RAMDISK_HIGH againMichal Simek
CONFIG_SYS_BOOT_RAMDISK_HIGH is already defined in arch/arm/include/asm/config.h:10:#define CONFIG_SYS_BOOT_RAMDISK_HIGH that's why there is no reason to define it again in board file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Remove all Xilinx private commandsMichal Simek
All platforms have been moved to distro boot that's why remove the rest of configurations to have unified boot flow. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Use {} around variables for qspi and nand boot cmdsMichal Simek
Follow conventions and used {} around variables. Fixes: 90e97ab31e02 ("arm: zynq: Define distro boot commnads for qspi, nand and nor") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Fix NOR boot modeMichal Simek
There are two typos in this command that's why it couldn't work properly. This bootmode is almost unused from the beggining on this SoC. Fixes: 90e97ab31e02 ("arm: zynq: Define distro boot commnads for qspi, nand and nor") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Enable USB1 as secondary boot deviceMichal Simek
Xilinx Zynq SoC has two usb controllers and both could be used as secondary boot method. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Specify MMC controller number for boot sequenceMichal Simek
Xilinx Zynq SoC has two sdhci controllers but boot is only possible from the first one. That's why there is a need to specify controller number. mmc1 is supposed to be secondary boot device and should be also listed in distribution boot. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-06 11:31:02 +0000