summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2018-05-18arm64: zynqmp: Use DWC3 generic driver and DM_USBMichal Simek
Remove harcoded XHCI lists and detect mode, speed based on DT. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Serial-changes: 2 - Remove also XHCI macros from hardware.h - Remove additional new line in zcu106
2018-05-18ARM: socfpga: Enable SPL memory allocationTien Fong Chee
Enable memory allocation in SPL for preparation to enable FAT in SPL. Memory allocation is needed by FAT to work properly. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18ARM: socfpga: Convert to DM serialMarek Vasut
Pull the serial port configuration from DT and use DM serial instead of having the serial configuration in two places, DT and board config. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18ARM: socfpga: Zap CONFIG_SOCFPGA_VIRTUAL_TARGETMarek Vasut
This was never used, is not used anywhere and is just in the way by adding annoying ifdeffery. Get rid of it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18ARM: socfpga: Put stack at the end of SRAMMarek Vasut
The global data are in the .data section, so there's no point in reserving any space for it above stack. Put stack at the end of SRAM. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-05-18arm: imx53: Add support for imx53 boards from K+PLukasz Majewski
This commit adds support for DDC and HSC boards from K+P in u-boot. Console output: U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: WDOG Model: K+P iMX53 DRAM: 512 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial Out: serial Err: serial Module EEPROM: ID: TQMa53-CB.0401 SN: 63152762 MAC: 00:0b:64:03:14:2a BBoard:40x0 Rev:10 Net: eth0: ethernet@63fec000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-18configs: imx6dl-mamoj: Add Falcon mode supportJagan Teki
Add Falcon mode support to boot Linux directly after SPL. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-18configs: imx6dl-mamoj: Add DFU supportJagan Teki
Add DFU support for BTicino Mamoj board and update the same steps in README. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
2018-05-18i.MX6: board: Add BTicino i.MX6DL Mamoj initial supportJagan Teki
Add initial support for i.MX6DL BTicino Mamoj board. Mamoh board added: - SPL - SPL_DM - SPL_OF_CONTROL - DM for U-Boot proper - OF_CONTROL for U-Boot proper - eMMC - FEC - Boot from eMMC - Boot from USB SDP Signed-off-by: Simone CIANNI <simone.cianni@bticino.it> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-05-17imx6: Convert sabrelite and nitrogen6x boards to distro boot supportGuillaume GARDET
Boot tested on sabrelite board. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Gary Bisson <gary.bisson@boundarydevices.com> Tested-by: Denis Pynkin <denis.pynkin@collabora.com>
2018-05-17ge: ppd: move CONFIG_ENV_IS_IN_MMC to defconfigSebastian Reichel
CONFIG_ENV_IS_IN_MMC must be declared in defconfig to properly support "env save". Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-05-17mx6: remove duplicated BOUNCE_BUFFER definesPeter Robinson
The mx6_common.h file already defines BOUNCE_BUFFER so no need to definit it again in specific configs. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2018-05-17mx6: Select CONFIG_MP with MX6_SMPPeter Robinson
It makes sense to select the MP multi processor option at the same time we select the other SMP options needed for SMP capable i.MX6 SoCs. Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2018-05-17mx7: remove empty ifndef statementPeter Robinson
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2018-05-17mx6 common: remove dangling commentPeter Robinson
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2018-05-17mx31pdk: Convert CONFIG_MX31 flag to use Kconfig.Magnus Lilja
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce necessary Kconfig changes as well. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-17board: ge: bx50v3: remove redundant targetsIan Ray
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3. The boards are identified automatically at runtime. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-05-17board: ge: bx50v3: configure video arguments using VPDIan Ray
Configure video arguments at run-time instead of at compile-time. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-05-14net: add Kconfig for MVGBEChris Packham
Add Kconfig for MVGBE and update boards to select this. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-14net: Add Kconfig option for BOOTP_NTPSERVERChris Packham
Add a Kconfig option for BOOTP_NTPSERVER to enable the DHCP/BOOTP option to configure the sntp server address. Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14treewide: Move CONFIG_PHY_MARVELL to KconfigMario Six
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards already had it in their Kconfig), but had not been moved for older boards. Move it to the defconfigs for all boards. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14rockchip: set SYS_NS16550_MEM32 for all SoCsJonathan Gray
Add back part of patch send out as 'rockchip: enable SYS_NS16550 for all SoCs by default' that seems to have gotten lost when it got merged to set SYS_NS16550_MEM32. Allows serial output to work on tinker-rk3288 again after c3c0331db1fb7b1f4ff41e144fc04353b37c785c. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-05-14arm64: mvebu: Add basic support for the Turris Mox boardMarek Behún
This adds basic support for the Turris Mox board from CZ.NIC, which is currently being crowdfunded on Indiegogo. Turris Mox is as modular router based on the Armada 3720 SOC (same as EspressoBin). The basic module can be extended by different modules. The device tree binary for the kernel can be dependent on which modules are connected, and in what order. Because of this, the board specific code creates in U-Boot a variable called module_topology, which carries this information. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-11Merge git://git.denx.de/u-boot-tegraTom Rini
2018-05-11SPDX: Correct SPDX tags from recent xilinx mergeTom Rini
Correct the SPDX tag format. Fixes: 3b52847a451a ("Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-11Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.07 microblaze: - Align defconfig zynq: - Rework fpga initialization and cpuinfo handling zynqmp: - Add ZynqMP R5 support - Wire and enable watchdog on zcu100-revC - Setup MMU map for DDR at run time - Show board info based on DT and cleanup IDENT_STRING zynqmp tools: - Add read partition support - Add initial support for Xilinx bif format for boot.bin generation mmc: - Fix get_timer usage on 64bit cpus - Add support for SD3.0 UHS mode nand-zynq: - Add support for 16bit buswidth - Use address cycles from onfi params scsi: - convert ceva sata to UCLASS_AHCI timer: - Add Cadence TTC for ZynqMP r5 watchdog: - Minor cadence driver cleanup
2018-05-11Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-05-11arm: zynqmp: Add ZynqMP minimal R5 supportMichal Simek
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot. This patch is adding minimal support to get U-Boot boot. U-Boot on R5 runs out of DDR with default configuration that's why DDR needs to be partitioned if there is something else running on arm64. Console is done via Cadence uart driver and the first Cadence Triple Timer Counter is used for time. This configuration with uart1 was tested on zcu100-revC. U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200) Model: Xilinx ZynqMP R5 DRAM: 512 MiB WARNING: Caches not enabled MMC: In: serial@ff010000 Out: serial@ff010000 Err: serial@ff010000 Net: Net Initialization Skipped No ethernet found. ZynqMP r5> There are two ways how to run this on ZynqMP. 1. Run from ZynqMP arm64 tftpb 20000000 u-boot-r5.elf setenv autostart no && bootelf -p 20000000 cpu 4 disable && cpu 4 release 10000000 lockstep or cpu 4 disable && cpu 4 release 10000000 split 2. Load via jtag when directly to R5 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm64: zynqmp: Add new defconfig for zc1275 revBSiva Durga Prasad Paladugu
This patch enables support zc1275 revB board. It has SD added compared to revA. The same configuration will work for RevC boards aswell. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-10configs: apalis-tk1: fix boot failure using ext4 rootfsSanchayan Maity
Trying to boot from an ext4 rootfs fails due to us defaulting to ext3. While the downstream T20/T30 L4T kernel has issues with ext4 later TK1 L4T should work just fine with it. Hence enable ext4 for sdboot and usbboot on TK1. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-10configs: harmony: enable live tree, mtd and ubiMarcel Ziswiler
U-Boot on Harmony recently got broken by ongoing driver model resp. live tree migration work: U-Boot 2018.03-rc3 (Feb 21 2018 - 15:43:08 +0100) TEGRA20 Model: NVIDIA Tegra20 Harmony evaluation board Board: NVIDIA Harmony DRAM: 1 GiB Video device 'dc@54200000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'tegra_lcd': -28 Some drivers failed to bind Error binding driver 'generic_simple_bus': -28 Some drivers failed to bind initcall sequence 3ffa86d0 failed at call 00121dc0 (err=-28) This commit fixes this by enabling live tree, MTD and UBI for Harmony as well. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-05-09armv8: ls1088a: Move CONFIG_BOOTARGS and CONFIG_CMD_GREPENV to defconfigAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-08arm: ti: boot: Extract PARTS_DEFAULT to boot.hSam Protsenko
Eliminate code duplication: the same PARTS_DEFAULT was defined in am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and use in all OMAP5-based boards. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2018-05-08ARM: meson: rename GXBB to GXNeil Armstrong
Taking into account the Amlogic Family name starts with GX, including the GXBB, GXL and GXM SoCs. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-05-07arm: stm32mp1: add PSCI supportPatrick Delaunay
Add PSCI v1.0 support for Linux and manage PSCI state for each CPU (affinity 0 level) with all mandatory functions: - PSCI_VERSION - CPU_SUSPEND - CPU_OFF - CPU_ON - AFFINITY_INFO - SYSTEM_OFF - SYSTEM_RESET - PSCI_FEATURES and 1 optional to avoid Linux warning - MIGRATE_INFO_TYPE Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: CITOOLS <smet-aci-reviews@lists.codex.cro.st.com>
2018-05-07SPDX: Convert all of our multiple license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have multiple licenses (in these cases, dual license) declared in the SPDX-License-Identifier tag. In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B" as per the Linux Kernel style document. Note that parenthesis are allowed so when they were used before we continue to use them. Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-02ARM: rmobile: Zap #undef DEBUGMarek Vasut
The DEBUG macro is never defined unless explicitly enabled. Drop useless #undef DEBUG in the board configs so it won't spread any further. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-02ARM: rmobile: Convert CONFIG_ARCH_RMOBILE_BOARD_STRING to KconfigMarek Vasut
Convert the symbol to Kconfig, no functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-02ARM: rmobile: Fix CONFIG_RMOBILE_BOARD_STRINGMarek Vasut
Rename CONFIG_RMOBILE_BOARD_STRING to CONFIG_ARCH_RMOBILE_BOARD_STRING to make things consistent, no functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-04-30Merge git://git.denx.de/u-boot-imxTom Rini
2018-04-28Cleanup CONFIG_SPL_SERIAL_SUPPORT migrationAlex Kiernan
CONFIG_SPL_SERIAL_SUPPORT had already been migrated to Kconfig, but existed in some include files; fix those up here. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-28arm: move SYS_ARCH_TIMER to KConfigAndre Przywara
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch timer) in U-Boot. At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards. Add a proper Kconfig symbol to express this dependency properly, allowing certain board configuration to later disable arch timer in case there are any problems with it. Signed-off-by: Andre Przywara <andre.przywara@arm.com> [tuomas: rebase + fix conflicts and resync with moveconfig & use select] Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2018-04-28ARM: qemu-arm: Dynamically determine timer frequencyTuomas Tynkkynen
After commit 46fc679ede5f69 ("arm: timer: get frequency for arch timer armv7 in cp15 cntfrq") the ARM architected timer driver knows how to determine the timer frequency at runtime by reading the CNTFRQ register, so we don't need to hardcode the timer frequency anymore. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2018-04-28Migrate IMAGE_FORMAT_LEGACY to KconfigAlex Kiernan
This converts IMAGE_FORMAT_LEGACY to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-28serial: Migrate CONFIG_FSL_LINFLEXUART to KconfigTuomas Tynkkynen
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-04-28ARM: s32v234evb: Set CONFIG_DM & CONFIG_DM_SERIAL in KconfigTuomas Tynkkynen
These symbols are declared in Kconfig, so it's wrong to set them in header files. Note that this is not size-neutral - some 'default y' options will now get turned on by Kconfig, such as CONFIG_CMD_DM=y and CONFIG_DM_STDIO=y. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-04-27configs: Drop CONFIG_NET_MULTITom Rini
We have not had CONFIG_NET_MULTI be meaningful for quite some time, drop the last remnants. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27Convert CONFIG_SPI to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27ARM: mxs: support full SPL frameworkMans Rullgard
This allows using the full SPL framework on mxs devices. In this mode, the u-boot.sb image loaded by the boot ROM contains only the SPL which then loads U-Boot proper or a kernel in falcon mode. Signed-off-by: Mans Rullgard <mans@mansr.com>
generated by cgit (git 2.34.1) at 2025-01-07 10:54:03 +0000