summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2018-03-20Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-03-20LS2088ARDB: Secure Boot: Fix fall back option failureVinitha V Pillai
Fix NOR, SD and QSPI fallback option in case of secure boot failure. Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088Ashish Kumar
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT. Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and IFC-NOR to be used as flash. This allows writing to IFC-NOR flash. QSPI and DSPI cannot be accessed in this defconfig. IFC-NOR image is generated using ls1088aqds_defconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20armv8: ls1088qds: Remove CONFIG_ from local defines for FPGAAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-19board: st: add generic board for STM32MP1 familyPatrick Delaunay
Add first support for STM32MP157C-ED1 board with "Basic" boot chain 1/ Boot Rom: load SPL with STM32 image header in SYSRAM 2/ SPL: power up and initialize the DDR and load U-Boot image from SDCARD in DDR 3/ U-Boot: search and load extlinux.conf in SDCARD (DISTRO activated) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19stm32f7: board: add splash screenyannick fertre
Support several pixel format (8bits, 16bits, 24bits & 32bits). Add new file st_logo_data.h which contains logo stmicroelectronics_uboot_logo_8bit_rle.bmp. Signed-off-by: yannick fertre <yannick.fertre@st.com>
2018-03-16Convert all of CONFIG_CONS_INDEX to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16configs: k2l: Updates u-boot env to install secure boot monitorMadan Srinivas
This patch updates the default u-boot env for K2L HS devices to install the secure boot monitor and load the fitImage during boot. Signed-off-by: Madan Srinivas <madans@ti.com> Acked-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-15ARM: uniphier: change load addresses for bigger kernel imageMasahiro Yamada
The kernel size is getting bigger and bigger. Because the Android common kernel is even bigger than the vanilla one, so images overlap in the current memory layout. Adjust the load address for a bigger kernel image. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-15ARM: uniphier: increase the firmware size in update command environmentMasahiro Yamada
If a bigger EL32 is used, fip.bin can be larger than the currently assumed boot firmware size. Adjust the update commands. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-14Merge git://git.denx.de/u-boot-sunxiTom Rini
2018-03-13ARM: omap3: evm: Sync with omap3_beagle configurationDerald D. Woods
This commit does the following for OMAP3 EVM: - Track omap3_beagle changes where possible - Remove CONFIG_SYS_MPUCLK and CONFIG_MTD which are not needed for the default board configuration to work. - Remove CONFIG_SPL_SYS_MALLOC_SIMPLE and CONFIG_SYS_MALLOC_F_LEN from default config. CONFIG_SYS_MALLOC_F_LEN=0x400 is set by configuration automatically. [allows board to boot with SERIAL_SEARCH_ALL=y] - Use updated NAND layout: device nand0 <omap2-nand.0>, # parts = 6 #: name size offset ------------------------------------------------- 0: spl 0x00080000(512k) 0x00000000 1: u-boot 0x001e0000(1920k) 0x00080000 2: u-boot-env 0x00020000(128k) 0x00260000 3: dtb 0x00020000(128k) 0x00280000 4: kernel 0x00600000(6m) 0x002a0000 5: rootfs 0x0f760000(-) 0x008a0000 ------------------------------------------------- Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-03-13ARM: omap3: beagle: Enable DM_SERIAL, update distro usage and NAND layoutDerald D. Woods
This commit does the following for BeagleBoard{-xM}: - Enable DM_SERIAL which also enables SPL_DM_SERIAL - Misc. config updates in support of DM_SERIAL - Use updated NAND layout (BeagleBoard): device nand0 <omap2-nand.0>, # parts = 6 #: name size offset ------------------------------------------------- 0: spl 0x00080000(512k) 0x00000000 1: u-boot 0x001e0000(1920k) 0x00080000 2: u-boot-env 0x00020000(128k) 0x00260000 3: dtb 0x00020000(128k) 0x00280000 4: kernel 0x00600000(6m) 0x002a0000 5: rootfs 0x0f760000(-) 0x008a0000 ------------------------------------------------- - Use MMC and UBIFS support from config_distro_bootcmd.h - Use LEGACY_MMC and NAND support defined in omap3_beagle.h [MMC(0:1)/extlinux/extlinux.conf] ---8<------------------------------------------------------------------- default omap3-beagle-mmc-fat label omap3-beagle-mmc-fat kernel /zImage fdt /omap3-beagle.dtb append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait ---8<------------------------------------------------------------------- [LEGACY_MMC(0:2)/boot/extlinux/extlinux.conf] ---8<------------------------------------------------------------------- default omap3-beagle-mmc-ext4 label omap3-beagle-mmc-ext4 kernel /boot/zImage fdt /boot/omap3-beagle.dtb append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait ---8<------------------------------------------------------------------- [UBIFS(ubi0:rootfs)/boot/extlinux/extlinux.conf] ---8<------------------------------------------------------------------- default omap3-beagle-nand-ubifs label omap3-beagle-nand-ubifs kernel /boot/zImage fdt /boot/omap3-beagle.dtb append console=ttyO2,115200n8 root=ubi0:rootfs rw ubi.mtd=rootfs rootfstype=ubifs rootwait ---8<------------------------------------------------------------------- The board's 'bootcmd' can also be overridden with: CONFIG_BOOTCOMMAND="run findfdt; run mmcboot" CONFIG_BOOTCOMMAND="run findfdt; run nandboot" CONFIG_BOOTCOMMAND="run findfdt; run ramboot" or CONFIG_BOOTCOMMAND="run findfdt; run somethingelse" The use of 'run findfdt' is required. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-03-13board: stm32: switch to DM STM32 timerPatrice Chotard
Use available DM stm32_timer driver instead of dedicated mach-stm32/stm32fx/timer.c. Remove all defines or files previously used for timer usage in arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx Enable DM STM32_TIMER for STM32F4/F7 and H7. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13rockchip: add text_offset to kernel_addr_r on aarch64 platformsKlaus Goger
Booting a aarch64 Linux kernel requires the image to be placed text_offset bytes from a 2MB aligned address. See https://www.kernel.org/doc/Documentation/arm64/booting.txt booti_setup() takes care about this alignment and will relocate the image if not properly aligned with memmove(). This can require up to double the size of the loaded image and therefore accidentally overwrite content placed there (i.e ramdisk_addr_r) for large kernel images. By adding text_offset to the default kernel_addr_r we can prevent that from happening for kernels larger 18MB and also save a few cycles. We can assume a text_offset of 0x80000 for most cases, all others will be handled by booti_setup() anyway. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-13Move CONFIG_PHY_ADDR to KconfigStefan Mavrodiev
CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-09ARM: Drop unreferenced CONFIG_* defines named after boardsTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_AT91SAM9263EK CONFIG_AT91SAM9RLEK CONFIG_BARIX_IPAM390 CONFIG_BOARD_H2200 CONFIG_EP9301 CONFIG_KZM_A9_GT CONFIG_PICOSAM CONFIG_PLATINUM_PICON CONFIG_PLATINUM_TITANIUM CONFIG_PM9261 CONFIG_PM9263 CONFIG_PM9G45 CONFIG_SIEMENS_DRACO CONFIG_SIEMENS_PXM2 CONFIG_SIEMENS_RUT CONFIG_SMDKC100 CONFIG_SMDKV310 CONFIG_STM32F4DISCOVERY Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-03-09ARM: Drop unreferenced CONFIG_* defines named after SoCsTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_ARM926EJS CONFIG_CPUAT91 CONFIG_EXYNOS5800 CONFIG_SYS_CORTEX_R4 Most of them are config symbols named after the respective SoCs which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-03-09MIPS: Drop unreferenced CONFIG_* definesTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_DBAU1X00 CONFIG_PB1X00 Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-03-09treewide: Fix gdsys mail addressesMario Six
The @gdsys.cc addresses are supposed to be used for mailing lists. Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc equivalent. Also, Dirk's address was wrong in one place; fix that as well. Signed-off-by: Mario Six <six@gdsys.cc>
2018-03-09ARM: qemu-arm: Increase CONFIG_SYS_CBSIZETuomas Tynkkynen
CONFIG_SYS_CBSIZE determines the maximum length of the kernel command line, and the default value of 256 is too small for booting some Linux images in the wild. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2018-03-05omap3_logic: Remove unnecessary undefsAdam Ford
Due to evolution of the MMC driver and better support, let's remove unnecessary undefs. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-03-05ti_armv7_omap: Remove comment remnantAdam Ford
With the migration to Kconfig, the I2C block no longer exists in here. Let's clean up the comment. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-03-05spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the ↵Faiz Abbas
U-boot CONFIG Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER. This enables users to block text using CONFIG_IS_ENABLED() instead of resorting to #if ladders with SPL and non-SPL cases. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-03-01Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2018-03-01Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-03-01mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQVipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01mmc: Added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQVipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01microblaze: Added Kconfig support for CONFIG_XILINX_GPIOVipul Kumar
This patch added Kconfig support for CONFIG_XILINX_GPIO and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Added kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1Vipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSETVipul Kumar
This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET and enabled it in respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEEDVipul Kumar
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED and set it to default value 100000. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVEVipul Kumar
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE and set it default to 0. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01i2c: Enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfigVipul Kumar
This patch enabled CONFIG_SYS_I2C_ZYNQ in the respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-02-28arm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPLVipul Kumar
This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the values over to the defconfigs. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2018-02-28fpga: Added Kconfig support for FPGA_SPARTAN3Vipul Kumar
This patch added Kconfig support for FPGA_SPARTAN3 and migrates the values over to the defconfigs. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2018-02-27Kconfig: cmd: Make networking command dependent on NETMichal Simek
Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-27ARM: rmobile: Build u-boot-spl.srec on Gen2Marek Vasut
The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs, conveniently generate this file if SPL is enabled. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Tom Rini <trini@konsulko.com>
2018-02-27ARM: rmobile: Build u-boot-elf.srec on Gen3Masaru Nagai
The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs, conveniently generate this file. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-02-26ARM: socfpga: Add new CycloneV SoC Devboards DBM-SoC1 boardMarek Vasut
Add support for a new boards from devboards.de , the DBM-SoC1 . This board has one ethernet port, one USB OTG port and USB UART. Signed-off-by: Marek Vasut <marex@denx.de>
2018-02-25bootcount: Migrate CONFIG_SYS_BOOTCOUNT_ADDRTom Rini
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can provide a default for BOOTCOUNT_AM33XX as that's a specific part of the RTC in use. We can also provide a default for ARCH_LS1043A and ARCH_LS1021A as they had been previously calculated and their symbols are in Kconfig. In the case of other QE-enabled platforms, they are not so we must update the relevant defconfig files. The previous default only applied in some cases, even on a specific SoC family. Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-24Migrate CONFIG_BOOTCOUNT_ALEN to KconfigAlex Kiernan
Convert CONFIG_BOOTCOUNT_ALEN to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Convert CONFIG_BOOTCOUNT_EXT to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_EXT Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-24Convert CONFIG_BOOTCOUNT_I2C to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_I2C Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_RAM to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_RAM Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_ENV to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_ENV Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-02-24Convert CONFIG_BOOTCOUNT_AM33XX to KconfigAlex Kiernan
This converts the following to Kconfig: CONFIG_BOOTCOUNT_AM33XX Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-02-23Remove config_distro_defaults.hAdam Ford
With the contents of config_distro_defaults.h migrated to Kconfig, we can remove this header file completely Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-23Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23Merge git://git.denx.de/u-boot-usbTom Rini
generated by cgit (git 2.34.1) at 2024-12-24 01:57:41 +0000