summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2007-05-15Merge with /home/wd/git/u-boot/masterWolfgang Denk
2007-05-15Merge with /home/tur/git/u-boot#motionproWolfgang Denk
2007-05-10[Motion-PRO] Add MTD and JFFS2 support, also add default partitionPiotr Kruszynski
definition.
2007-05-08[Motion-PRO] Add support for I2C, EEPROM and RTC.Piotr Kruszynski
2007-05-08[Motion-PRO] Add ATA support. Add CF-booting commands to the defaultBartlomiej Sieka
environment.
2007-05-08[Motion-PRO] Change IPB clock frequency from 50MHz to 100MHz. ThisBartlomiej Sieka
eliminates networking problems in Linux (timeouts).
2007-05-08[Motion-PRO] Enable Flat Device Tree support and modify default environmentBartlomiej Sieka
to allow booting of FDT-expecting kernels.
2007-05-07Get rid of duplicated file (see include/configs/sbc8560.h instead)Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-05Coding stylke cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-mpc85xxWolfgang Denk
2007-05-05Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-05-05ppc4xx: Detect if the sysclk on Sequoia is 33 or 33.333 MHzJeffrey Mann
The AMCC Secquoia board has been changed in a new revision from using a 33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD indicates the difference. This patch reads that bit and uses the correct clock speed for the board. This code is backward compatable will all prior boards. All prior boards will be read as 33.000. Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-05Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-05-03Update board configuration for STX GP3SSA board:Wolfgang Denk
Enable hush shell, environment in flash rather in EEPROM, more user-friendly default environment, etc. The simple EEPROM environment can be selected easily in the board config file. Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-03Add support for STX GP3SSA (stxssa) BoardDan Malek
Signed-off-by Dan Malek, <dan@embeddedalley.com>
2007-05-02Cleaned up some 85xx PCI bugsAndy Fleming
* Cleaned up the CDS PCI Config Tables and added NULL entries to the end * Fixed PCIe LAWBAR assignemt to use the cpu-relative address * Fixed 85xx PCI code to assign powar region sizes based on the config values (rather than hard-coding them) * Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-05-02Add support for the 8568 MDS boardAndy Fleming
This included some changes to common files: * Add 8568 processor SVR to various places * Add support for setting the qe bus-frequency value in the dts * Add the 8568MDS target to the Makefile Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-29Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-04-29ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driverStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-23Add MPC8544DS main configuration file.Jon Loeliger
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-04-23Fix PCI I/O space mapping on Freescale MPC85x0ADSSergei Shtylyov
The PCI I/O space mapping for Freescale MPC8540ADS board was broken by commit 52c7a68b8d587ebcf5a6b051b58b3d3ffa377ddc which failed to update the #define's describing the local address window used for the PCI I/O space accesses -- fix this and carry over the necessary changes into the MPC8560ADS code since the PCI I/O space mapping was also broken for this board (by the earlier commit 087454609e47295443af793a282cddcd91a5f49c). Add the comments clarifying how the PCI I/O space must be mapped to all the MPC85xx board config. headers. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> board/mpc8540ads/init.S | 4 ++-- board/mpc8560ads/init.S | 4 ++-- include/configs/MPC8540ADS.h | 5 ++--- include/configs/MPC8541CDS.h | 2 +- include/configs/MPC8548CDS.h | 2 +- include/configs/MPC8560ADS.h | 8 ++++---- 6 files changed, 12 insertions(+), 13 deletions(-)
2007-04-23u-boot: Disables MPC8548CDS 2T_TIMING for DDR by defaultebony.zhu@freescale.com
This patch disables MPC8548CDS 2T_TIMING for DDR by default. Signed-off-by:Ebony Zhu <ebony.zhu@freescale.com>
2007-04-23u-boot: Enable PCI function and add PEX & rapidio memory map on MPC8548CDS boardZang Roy-r61911
Enable PCI function and add PEX & rapidio memory map on MPC8548CDS board. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2007-04-23Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-04-23Remove BOARDLIBS usage completelyStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-20Merge with /home/dzu/src/git/u-bootWolfgang Denk
2007-04-20Fix breakage of NC650 board with respect to nand support.Detlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de>
2007-04-20[RFC PATCH] icecube/lite5200b: fix OF_TBCLK (timebase-frequency) calculationDomen Puncer
G2 core reference manual says decrementer and time base are decreasing/increasing once every 4 bus clock cycles. Lets fix it, so time in Linux won't run twice as fast Signed-off-by: Domen Puncer <domen.puncer@telargo.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2007-04-19ppc4xx: Fix chip select timing for SysACE access on AMCC KatmaiStefan Roese
Previous versions used full wait states for the chip select #1 which is connected to the Xilinix SystemACE controller on the AMCC Katmai evaluation board. This leads to really slow access and therefore low performance. This patch now sets up the chip select a lot faster resulting in much better read/write performance of the Linux driver. Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-74xx-7xxWolfgang Denk
2007-04-18Merge with /home/wd/git/u-boot/custodian/u-boot-avr32; code cleanup.Wolfgang Denk
2007-04-14AVR32: Enable MMC supportHaavard Skinnemoen
Set up the portmux for the MMC interface and enable the MMC driver along with support for DOS partitions, ext2 and FAT filesystems. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14AVR32: Enable networkingHaavard Skinnemoen
Implement MACB initialization for AVR32 and ATSTK1000, and turn everything on, including the MACB driver. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14AVR32: Include more commands for ATSTK1000Haavard Skinnemoen
Include the imi, imls and jffs commands sets by default on ATSTK1000. Also define CONFIG_BOOTARGS to something more useful, define CONFIG_BOOTCOMMAND and enable autoboot by default. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14AVR32: Relocate u-boot to SDRAMHaavard Skinnemoen
Relocate the u-boot image into SDRAM like everyone else does. This means that we can handle much larger .data and .bss than we used to. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14AVR32: Resource management rewriteHaavard Skinnemoen
Rewrite the resource management code (i.e. I/O memory, clock gating, gpio) so it doesn't depend on any global state. This is necessary because this code is heavily used before relocation to RAM, so we can't write to any global variables. As an added bonus, this makes u-boot's memory footprint a bit smaller, although some functionality has been left out; all clocks are enabled all the time, and there's no checking for gpio line conflicts. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-12Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-04-11Update for SC3 boardWolfgang Denk
* Make IDE timeout configurable through ide_reset_timeout variable. * Use Newline as "password" string * Use just a single partition in NAND flash
2007-04-04Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-04-04Minor coding style cleanup.Wolfgang Denk
2007-04-04Merge with /home/wd/git/u-boot/custodian/u-boot-microblazeWolfgang Denk
2007-04-02ppc4xx: Change SysACE address on KatmaiStefan Roese
With this new base address of the Xilinx SystemACE controller the Linux driver will be easier to adapt, since it can now be mapped via the "normal" ioremap() call. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31Add a flattened device tree (fdt) command (2 of 2)Gerald Van Baren
Modifications to the existing code to support the new fdt command.
2007-03-31Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-03-31ppc4xx: Change Yucca config file to support ECCStefan Roese
With the updated 44x DDR2 driver the Yucca board now supports ECC generation and checking. Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-30[CLEAN] Remove inefficient Suzaku codeMichal Simek
2007-03-29Merge with /home/wd/git/u-boot/custodian/u-boot-mpc86xxWolfgang Denk
2007-03-28Merge some AMCC make targets to keep the top-level Makefile smallerStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-26Support for XUPV2P boardMichal Simek
Reset support BSP autoconfig support