summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2007-12-04ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-29Merge git://www.denx.de/git/u-bootNobuhiro Iwamatsu
Conflicts: drivers/Makefile
2007-11-27ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexingStefan Roese
After an error in the AMCC 405EX users manual now correctly configure IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ usage. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-26ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usageStefan Roese
As suggested by Senao, use a different EBC_PB0AP setup for 400MHz operation. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-26ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interruptStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-20[BUILD] conditionally compile common/cmd_*.c in common/MakefileGrant Likely
Modify common/Makefile to conditionally compile the cmd_*.c files based on the board config. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-11-208610HPCD: Enable the 8610 Display Interface UnitJon Loeliger
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-11-20Merge commit 'remotes/wd/master'Jon Loeliger
2007-11-19Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDSHaiying Wang
CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2007-11-17ppc4xx: Update AMCC Kilauea config fileStefan Roese
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-17Fix the i2c frequency and default address in rsdproto boardLuotao Fu
rsdproto board support has wrong I2C frequency and wrong return value handling. Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
2007-11-17Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk
2007-11-17Unify pixis_reset altbank across board familiesJason Jin
Basically, refactor the CFG_PIXIS_VBOOT_MASK values into the separate board config files. Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-11-16ppc4xx: Update AMCC Makalu for board rev 1.1Stefan Roese
This patch adds changes needed for Makalu rev 1.1: - Enable 2nd DDR2 bank resulting in 256MByte of SDRAM - Enable 2nd ethernet port EMAC1 - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) - Reset PCIe ports via GPIO upon bootup Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405 platformsStefan Roese
- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE - Cleanup of the 4xx GPIO functions - Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15ppc4xx: AMCC Taihu board config file cleanupStefan Roese
This patch makes the AMCC Taihu a little more compatible to the other AMCC eval boards. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15[INKA4x0] NG hardware: flash supportMarian Balakowicz
Disabled and remove inka4x0 custom flash driver, use CFI flash driver instead. Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2007-11-15[INKA4x0] NG hardware: SDRAM supportMarian Balakowicz
Add support for three new DDR chips that may be present on a NG INKA4x0 hardware: HYB25D512160BF-5, K4H511638C-7CB3, T46V32M16BN-6IT. Cleanup board/inka4x0/mt48lc16m16a2-75.h file. Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2007-11-15[INKA4x0] NG hardware: platform code updateMarian Balakowicz
- Cleanup compile warnings. - Add missing '\0' in default environment. - Increase CFG_MONITOR_LEN to 256 KiB. - Add required CFG_USE_PPCENV. Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2007-11-13Enable ULi1575 Ethernet support in 8610HPCD configRoy Zang
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
2007-11-13Merge branch 'master' of git://www.denx.de/git/u-bootStefan Roese
2007-11-13[UC101] SRAM now with 2 MB working.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2007-11-09ppc4xx: Use generic usb-ohci driver for sequoia boardMatthias Fuchs
This patch makes the sequoia board use the generic usb-ohci driver instead of cpu/ppc4xx/usb_ohci.c. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09ppc4xx: Remove In:/Out:/Err: boot output for AMCC KilaueaStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-07Merge branch 'mpc8610'Jon Loeliger
2007-11-078610: Add console frame buffer support to FSL 8610 DIU driver.York Sun
Add cfb console support to FSL 8610 DIU driver. Inspect board version from PIXIS to obtain correct pixel format. Use #define CONFIG_VIDEO in config file to enable fb console. To switch monitor, set monitor variable to 0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS followed by "diufb init". Preserve logo bitmap at the top of the fb console. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-11-078610: Add 8610 DIU display driverYork Sun
1280x1024 and 1024x768 @ 32 bpp are supported now. DVI, Single-link LVDS, Double-link LVDS are all supported. Environmental variable "monitor" is used to specify monitor port. A new command "diufb" is introduced to reinitialize monitor and display a BMP file in the memory. So far, 1-bit, 4-bit, 8-bit and 24-bit BMP formats are supported. diufb init - initialize the diu driver Enable the port specified in the environmental variable "monitor" diufb addr - display bmp file in memory. The bmp image should be no bigger than the resolution, 1280x1024 for DVI and double-link LVDS, 1024x768 for single-link LVDS. Note, this driver allocate memory but doesn't free it after use It is written on purpose -- to avoid a failure of reallocation due to memory fragement. ECC of DDR is disabled for DIU performance. L2 data cache is also disabled. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Jon loeliger <jdl@freescale.com>
2007-11-078610: Make some extra debug environment variables conditional.York Sun
One may #define ENV_DEBUG to get them back again. Signed-off-by: York Sun <yorksun@freescale.com>
2007-11-078610: Actually enable pixis_reset CONFIGsJason Jin
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2007-11-07Fix the BAT definition of PCI IO on 8610 boardJason Jin
The address in the BAT register is aligned with the BAT size. The original definition actually did not define BAT for PCIE2 IO. This patch fix this. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2007-11-07Unify pixis_reset altbank across board familiesJason Jin
Basically, refactor the CFG_PIXIS_VBOOT_MASK values into the separate board config files. Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-11-07Merge commit 'remotes/wd/master' into newmasterJon Loeliger
2007-11-03Cleanup coding style; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-11-03Fix USB support issue for MPC8641HPCN board.Zhang Wei
The configuration file has already enabled USB, but it missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB on MPC8641HPCN can not work because of the wrong USB register endian. And add the USB command to U-Boot commands list. Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
2007-11-03Use config_cmd_default.h instead of config_cmd_all.hJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-03changes for IDS8247 board supportSergej Stepanov
To get the IDS8247 board working following are done: - FCC2 is deactivated - FCC1 is activated - I2C is activated - CFI driver is activated - Adapted for use with LIBFDT Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de> --
2007-11-03ppc4xx: Add AMCC Kilauea/Haleakala NAND booting supportStefan Roese
This patch adds NAND booting support for the AMCC 405EX(r) eval boards. Again, only one image supports both targets. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-02Merge commit 'remotes/wd/master'Jon Loeliger
2007-11-02Merge branch 'master' of /home/wd/git/u-boot/workWolfgang Denk
2007-11-02Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2007-11-01ATSTK1002: Remove default ethernet addressesHaavard Skinnemoen
Wolfgang is right: It's not a good idea to set up default initial ethernet addresses for a board, even though they belong to the local range. This will change the failure mode from "IT manager screams at you for using duplicate ethernet addresses" to a nice error message explaining that the ethernet address hasn't been set properly. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-coldfireWolfgang Denk
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-tq-groupWolfgang Denk
2007-11-01Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xxWolfgang Denk
2007-10-31ppc4xx: Remove cache definition from 4xx board config filesStefan Roese
All 4xx board config files don't need the cache definitions anymore. These are now defined in common headers. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board supportStefan Roese
The Haleakala is nearly identical with the Kilauea eval board. The only difference is that the 405EXr only supports one EMAC and one PCIe interface. This patch adds support for the Haleakala board by using the identical image for Kilauea and Haleakala. The distinction is done by comparing the PVR. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add SNTP support to AMCC Katmai, Kilauea & Makalu boardsStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add initial AMCC Makalu 405EX supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc: Small Kilauea cleanup of config fileStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2024-12-26 15:43:58 +0000