| Age | Commit message (Collapse) | Author |
|---|
|
EFI was disabled in f95b8a4b5f64f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
|
|
Currently this causes failures of the platform when running the EFI
loader tests, so disable it for now.
This reverts commit af827140e5965e5bb2bcad1c53ca8419b428ff6d.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fixed for rv1108 and elgin-rv1108 board
- Fix the keyboard from USB instead of CrOS EC
|
|
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
EFI was disabled in f95b8a4b5f64f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti into next
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
|
|
- DM support for CAxxxx SoCs
- eMMC board for presidio-asic
- Add defer probe for mmc sdhci
- TI SoCs mmc misc update
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.04
-----------------
- DM : mx6sabresd
- mx6ul_14x14_evk: fix video
- mx8qxp; fix console for booting
- sync DTS with kernel (imx6sx)
- drop obsolete woodburn (mx35)
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/660550811
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.04 cycle:
- Includes two small configuration fixes that will solve the SPL booting
on sama5d3_xplained board.
|
|
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Set CONFIG_SYS_BOOTMAPSZ to the amount of memory available which is needed
to relocate the kernel, device tree and initrd.
Remove 'fdt_high' and 'initrd_high' environment variables from default
environment which prevents relocation of FDT and initrd.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Uboot size is incorrect.
Uboot SPL use CONFIG_SYS_MONITOR_LEN to read uboot from NAND : 0x80000
With sama5d3_xplained_nandflash_defconfig : u-boot.bin size is ~800Ko 0xC0000
So I increased size to 1MB : 0x100000
Signed-off-by: Fabien Lehoussel <fabien.lehoussel@medianesysteme.com>
|
|
Added missing USDHC Base address defines
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
fdt_high value of 0xffffffff disables fdt relocation on boot. We don't
need that for Cubox-i/Hummingboard. Rely on generic code to find the
optimal fdt location at boot time.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Currently the expansion of the console variable leads to
the following kernel command line:
console=ttyLP0,${baudrate} earlycon root=/dev/mmcblk1p2 rootwait rw
, which causes the console to not show characters after the LPUART driver
is probed as the 'baudrate' variable is not properly translated.
Fix it by splitting the console variable in two parts: one for the
ttyLP0 part and the other one for the baudrate, which matches the way
it is done on other i.MX targets.
Tested by successfully booting a mainline kernel on a i.MX8QXP MEK
board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Board is not longer used, remove it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
With CONFIG_SUPPORT_EMMC_BOOT moved to Kconfig, move it to defconfig
files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
- Limit bootloader size to 1 MiB on R-Car Gen3
|
|
- ABB SECU board
- Assorted minor fixes
|
|
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Fix building errors if CONFIG_DM_VIDEO is enabled. This is the only
u-boot board that enables CONFIG_AM335X_LCD and from which I started
to develop the version of the frame buffer driver that supports the
driver model.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
main_r5fss0_core0
Add env variables for mcu_r5fss0_core0 & main_r5fss0_core0 firmware
loadaddr and name.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Set up mtdparts cmdline argument to be passed to kernel
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Set up mtdparts cmdline argument to be passed to kernel
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx fixes for v2020.04-rc4
- Fix link good bit handling in dp83867
- Rename generic Zynq defconfig
- Fix zybo z7 low leve setup
- Fix error path in zynq_gem driver and fix 64bit usage
- Fix invalid clock name quieries for Versal
- Fix zynq/zynqmp SPL low level configuration via DT selection
|
|
The Denali SPL shim won't build without these options set,
set them accordingly to fix the build error and let the SPL
shim to work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
The default timer rate may be different than 25 MHz, permit overriding
the default rate in board configuration file. Ultimatelly, this should
be properly handled by a clock driver, however that is not available
on Gen5 yet.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
The HF/QSPI flash layout permits up to 1 MiB large bootloader blob,
set CONFIG_BOARD_SIZE_LIMIT to enforce this limit and set the
monitor size to match accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Very likely configs have been moved to Kconfig by scripts and this just
remains there that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add handy macros:
- sdscript: source boot.scr in the file system of the SD media
- sdboot : boot the kernel using the images in the file system
of the SD media
- sdscript: update the boot firmware in the SD media
(in raw block sectors)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add console settings like stdin, stdout and stderr as
cros-ec-keyb and vidconsole respectively for Vyasa Rk3288
board.
This would certainly help to detect the attached video
devices (like HDMI) and print the console message on display.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Enable HDMI output for Tinker RK3288 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
|
|
For stm32 f4, f7 and h7 boards, remove fdt_high and
initrd_high as they shouldn't be used, this allows the fdt
and initrd relocation.
This implies to set CONFIG_SYS_BOOTMAPSZ to indicate the
amount of memory available to contain kernel, device tree
and initrd for relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
|
|
For stm32f4, f7 and h7 boards, reserve:
- 4MB for kernel
- 64KB for fdt, boot script, pxefile
- the remaining memory for ramdisk
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
|
|
Remove fdt_high and initrd_high as they shouldn't be used,
this allows the fdt and initrd relocation.
This implies to set CONFIG_SYS_BOOTMAPSZ to indicate the
amount of memory available to contain kernel, device tree
and initrd for relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
|
|
Remove fdt_high and initrd_high (set to 0xffffffff) in stm32mp1 board
enviromnent, and U-Boot always relocate FDT and initrd in bootm command.
This relocation is limited by CONFIG_SYS_BOOTMAPSZ which indicates
the size of the memory region where it is safe to place data passed
to the Linux kernel (DTB, initrd), it is
a) Less than or equal to RAM size.
b) not within the kernel's highmem region
So 256M seems large enough in most circumstances and users
can override this value via environment variable "bootm_mapsize"
if needed.
This modification increases the boot time but avoid assumption
on aligned address for bootm command.
A user can still define this variables themselves if the FDT or
initrd is either left in-place or copied to a specific location.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Keystone2 u-boot loads the initrd image into non-LPAE addressed memory
but linux kernel is running in LPAE. This causes a conflict as kernel
detects that non-memory address is passed and kernel ignores initrd.
There is an existing fixup logic to modify the address in the proper
configuration, but this is disabled at the moment. Enable the fixup
by setting the env variable for this so that initrd can be used
properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Configure `CONFIG_SYS_BOOTMAPSZ' per guidance on u-boot@lists.denx.de.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Use `test' command to test for file existence instead of relying on the
old functionality of the `ext2load' command (which now reports an error
when attempting to load a zero length file).
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy uart pad and iomux code
Enable DM serial and mxc uart
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
