summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2007-12-08ppc4xx: 405EX: Correctly enable USB pinsStefan Roese
This patch selects the USB data pins in the 405EX GPIO and MFC (multi function control) registers. This is done for the AMCC Kilauea and Makalu eval boards. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-04ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-27ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexingStefan Roese
After an error in the AMCC 405EX users manual now correctly configure IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ usage. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-26ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usageStefan Roese
As suggested by Senao, use a different EBC_PB0AP setup for 400MHz operation. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-26ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interruptStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-17ppc4xx: Update AMCC Kilauea config fileStefan Roese
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-16ppc4xx: Update AMCC Makalu for board rev 1.1Stefan Roese
This patch adds changes needed for Makalu rev 1.1: - Enable 2nd DDR2 bank resulting in 256MByte of SDRAM - Enable 2nd ethernet port EMAC1 - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) - Reset PCIe ports via GPIO upon bootup Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405 platformsStefan Roese
- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE - Cleanup of the 4xx GPIO functions - Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15ppc4xx: AMCC Taihu board config file cleanupStefan Roese
This patch makes the AMCC Taihu a little more compatible to the other AMCC eval boards. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09ppc4xx: Use generic usb-ohci driver for sequoia boardMatthias Fuchs
This patch makes the sequoia board use the generic usb-ohci driver instead of cpu/ppc4xx/usb_ohci.c. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09ppc4xx: Remove In:/Out:/Err: boot output for AMCC KilaueaStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-03ppc4xx: Add AMCC Kilauea/Haleakala NAND booting supportStefan Roese
This patch adds NAND booting support for the AMCC 405EX(r) eval boards. Again, only one image supports both targets. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Remove cache definition from 4xx board config filesStefan Roese
All 4xx board config files don't need the cache definitions anymore. These are now defined in common headers. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board supportStefan Roese
The Haleakala is nearly identical with the Kilauea eval board. The only difference is that the 405EXr only supports one EMAC and one PCIe interface. This patch adds support for the Haleakala board by using the identical image for Kilauea and Haleakala. The distinction is done by comparing the PVR. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add SNTP support to AMCC Katmai, Kilauea & Makalu boardsStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add initial AMCC Makalu 405EX supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc: Small Kilauea cleanup of config fileStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Change inbound PCIe location for endpoint tests on KatmaiStefan Roese
On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which is the internal SRAM. Since I now ported and tested this endpoint mode on Kilauea successfully to map to 0 (SDRAM), I also changed this for Katmai. Yucca will stay at internal SRAM for now. Not sure if somebody relies on this setup. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint modeStefan Roese
This patch adds support for dynamic configuration of PCIe ports for the AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe boards Yucca & Katmai and the 405EX board Kilauea. This dynamic configuration is done via the "pcie_mode" environement variable. This variable can be set to "EP" or "RP" for endpoint or rootpoint mode. Multiple values can be joined via the ":" delimiter. Here an example: pcie_mode=RP:EP:EP This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2 as endpoint. Per default Yucca will be configured as: pcie_mode=RP:EP:EP Per default Katmai will be configured as: pcie_mode=RP:RP:REP Per default Kilauea will be configured as: pcie_mode=RP:RP Signed-off-by: Tirumala R Marri <tmarri@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Enable device tree support (fdt) on Kilauea per defaultStefan Roese
This patch enables the fdt support on the AMCC Kilauea eval board. Additionally now EBC ranges fdt fixup is included to support NOR FLASH mapping via the Linux physmap_of driver. This Kilauea port now support booting arch/ppc and arch/powerpc Linux kernels. The default environment "net_nfs" is for arch/ppc and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc support will be removed. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: Add initial AMCC Kilauea 405EX supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31DTT: Prepare DS1775 driver for use of different I2C addressesStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: 4xx_pcie: More general cleanup and 405EX PCIe support addedStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31ppc4xx: 4xx_pcie: Change CFG_PCIE_MEMSIZE to 128MB on Yucca & KatmaiStefan Roese
128MB seems to be the smallest possible value for the memory size for on PCIe port. With this change now the BAR's of the PCIe cards are accessible under U-Boot. One big note: This only works for PCIe port 0 & 1. For port 2 this currently doesn't work, since the base address is now 0xc0000000 (0xb0000000 + 2 * 0x08000000), and this is already occupied by CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean to change the base addresses completely and this change would have too much impact right now. This patch adds debug output to the 4xx pcie driver too. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-27Merge git://www.denx.de/git/u-bootStefan Roese
2007-10-25TQM5200: increase kernel_addr_r and fdt_addr_r (hinted by Wolfgang Denk).Bartlomiej Sieka
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2007-10-24Merge branch 'motionpro_ng' of /home/tur/git/u-bootWolfgang Denk
2007-10-24TQM5200: fix spurious characters on second serial interfaceMartin Krause
With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-24delta: Fix OHCI_REGS_BASE undeclared and wait_ms implicit declarationJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-24xsengine: Fix no partition type specified, use DOS as defaultJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-24lubbock: Fix no partition type specified, use DOS as defaultJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-23fix pxa255_idp boardMarcel Ziswiler
The pxa255_idp being an old unmaintained board showed several issues: 1. CONFIG_INIT_CRITICAL was still defined. 2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined. 3. Symbol flash_addr was undeclared. 4. The boards lowlevel_init function was still called memsetup. 5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000. 6. Using -march=armv5 instead of -march=armv5te resulted in lots of 'target CPU does not support interworking' warnings on recent compilers. 7. The PXA's serial driver redefined FFUART, BTUART and STUART used as indexes rather than the register definitions from the pxa-regs header file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to avoid any ambiguities. 8. There were several redefinition warnings concerning ICMR, OSMR3, OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file. 9. The board configuration file was rather outdated. 10. The part header file defined the vendor, product and revision arrays as unsigned chars instead of just chars in the block_dev_desc_t structure. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2007-10-23Make MPC8266ADS command selection more robustRune Torgersen
Fix MPC8266 command line definition so it won't break when new commands are added to u-boot. Signed-off-by Rune Torgersen <runet@innovsys.com>
2007-10-23Motion-PRO: Update configuration to accomodate next generation board.Bartlomiej Sieka
New board has faster oscillator and a different Flash chip. This affects: - CFG_MPC5XXX_CLKIN - SDRAM timings - Flash CS configuration (timings) - Flash sector size, and thus MTD partition layout - malloc() arena size (due to bigger Flash sectors) - smaller memory test range (due to bigger malloc() arena) This patch also enables more extensive memory testing via "mtest". Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2007-10-23ppc4xx: lwmon5: Some further GPIO config changesStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-21Merge branch 'master' of git://www.denx.de/git/u-boot-tq-groupWolfgang Denk
2007-10-21Merge branch 'master' of /home/git/u-boot/Wolfgang Denk
2007-10-16Make MPC8266ADS board compile again.runet@innovsys.com
Signed-off-by: Runet Torgersen <runet@innovsys.com>
2007-10-15ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & YosemiteStefan Roese
The BCSR status bit for the 66MHz PCI operation was correctly addressed (MSB/LSB problem). Now the correct currently setup PCI frequency is displayed upon bootup. This patch also fixes this problem on Rainier & Yellowstone, since these boards use the same souce code as Sequoia & Yosemite do. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-15TQM860M: adjust for doubled flash sector size.Martin Krause
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with doubled sector size. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-15TQM866M: fix SDRAM refreshMartin Krause
At 133 MHz the current SDRAM refresh rate is too fast (measured 4 * 1.17 us). CFG_MAMR_PTA changes from 39 to 97. This result in a refresh rate of 4 * 7.8 us at the default clock 50 MHz. At 133 MHz the value will be then 4 * 2.9 us. This is a compromise until a new method is found to adjust the refresh rate. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-15TQM866M: adjust for doubled flash sector size.Martin Krause
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with doubled sector size. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-14[FIX] XUPV2P change command handlingMichal Simek
and remove code violation
2007-10-13Merge branch 'master' of git://www.denx.de/git/u-boot-avr32Wolfgang Denk
2007-10-13Merge branch 'merge' of git://www.denx.de/git/u-boot-microblazeWolfgang Denk
2007-10-13Coding Style cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-10-12GP3 SSA: enable RTCWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-10-10Merge branch 'master' of /.automount/castor-vlab/root/home/wd/git/u-boot/master/Wolfgang Denk
2007-10-10Merge branch 'hellrosa_i2c' of /home/gjb/git/u-bootWolfgang Denk
2007-10-10Merge branch 'tqm5200_default_env' of /home/tur/git/u-bootWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-27 06:54:36 +0000