summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2013-11-09malta: enable RTC supportPaul Burton
This is actually required in order for a Linux kernel to boot successfully on a physical Malta board. Without enabling the RTC, a Malta Linux kernel will get stuck in its estimate_frequencies function on boot. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: remove cache size definitionsPaul Burton
These will now be detected at runtime, allowing a single U-boot configuration to function correctly with different bitstreams. Without this you may need to re-configure, re-build and re-flash U-boot to your Malta if you flash a new bitstream with a different cache configuration to your old bitstream. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: enable CONFIG_PCNET_79C973, PCNET_HAS_PROM, CONFIG_CMD_DHCPPaul Burton
This model of the pcnet is used in current Malta boards, at least in the Malta-R rev 3. Enable support for it. The Malta also has the ethernet controller PROM containing its MAC address, so enable support for that in order to read that MAC address. DHCP is a very useful feature to have available for many networks, enable support for it also. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: support for coreFPGA6 boardsPaul Burton
This patch adds support for running on Malta boards using coreFPGA6 core cards, including support for the msc01 system controller used with them. The system controller is detected at runtime allowing one U-boot binary to run on a Malta with either. Due to the PCI I/O base differing between Maltas using gt64120 & msc01 system controllers, the UART setup is modified slightly. A second UART is added so that there is one pointing at the correct address for each system controller. The Malta board then defines its own default_serial_console function to select the correct one at runtime. The incorrect UART will simply not function. Tested on: - A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both with and without an L2 cache. - QEMU. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09qemu-malta: rename to just "malta"Paul Burton
This is in preparation for adapting this board to function correctly on a physical MIPS Malta board. The board is moved into an "imgtec" vendor directory at the same time in order to ready us for any other boards supported by Imagination in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-08Merge branch 'master' of git://www.denx.de/git/u-boot-usbTom Rini
2013-11-08sandbox: convert to common time functionsRob Herring
Convert sandbox to use common time functions. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-08highbank: set AUTOBOOT_KEYED_CTRLC config optionMark Langsdorf
Let highbank users break into the autoboot script with ctrl-c. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08config/sandbox: Add EFI and GPT supportEgbert Eich
Signed-off-by: Egbert Eich <eich@suse.com>
2013-11-08usb: ums: move ums code from trats to Samsung common directoryPrzemyslaw Marczak
UMS init was implemented in trats board file but mostly it comprises common code. Due to that it has been moved to common/ums.c to avoid code duplication in the future. Changes: - move ums initialization code from trats to common/ums.c - remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h Changes v2: - move this patch at the top of code cleanups patches Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Minkyu Kang <mk7.kang@samsung.com>
2013-11-08EP88x: remove remainders of dead boardMasahiro Yamada
Commit 1b0757e deleted the EP88x entry from boards.cfg file. But it missed to remove include/configs/EP88x.h and board/ep88x/. This commit removes them and adds EP88x to README.scrapyard. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
2013-11-07Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-06ColdFire: fix some typoes for CF platformjason
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
2013-11-06coldfire: cpu5282: increase malloc space to fix crash on start u-bootJens Scharsig (BuS Elektronik)
The malloc space is to small to boot, the current uboot 2013.10-rcX, This will fix the startup problems by increasing the mallog space to 4MiB. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2013-11-05Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-04ARM: ATMEL: eb_cpux9k2: fix TEXT_BASE for ramboot targetJens Scharsig (BuS Elektronik)
Since more functions are enabled, the eb_cpux9k2_ram target does not boot. This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04arm: atmel: get rid of too many ifdefferyBo Shen
Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04arm: atmel: at91sam9n12ek: add usb host supportBo Shen
Add usb host support for at91sam9n12ek board. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04ARM: versatile: convert to common timer codeRob Herring
Convert versatile to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: tegra: convert to common timer codeRob Herring
Convert tegra to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: socfpga: convert to common timer codeRob Herring
Convert socfpga to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: vexpress: convert to common timer codeRob Herring
Convert vexpress to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: mx25: convert to common timer codeRob Herring
Convert mx25 to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: highbank: convert to common timer codeRob Herring
Convert highbank to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04config: remove platform CONFIG_SYS_HZ definition part 2/2Rob Herring
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04config: remove platform CONFIG_SYS_HZ definition part 1/2Rob Herring
Remove platform CONFIG_SYS_HZ definition for configs A-Z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04config: Add a default CONFIG_SYS_PROMPTRob Herring
The definitions for CONFIG_SYS_PROMPT are varied with little reason other than to display the board name. Over half the definitions are "==> ", so make this the default. The rest of the boards remain unchanged to avoid breaking any external scripts expecting a certain prompt. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-11-04Revert "configs: imx: Make CONFIG_SYS_PROMPT uniform across FSL boards"Stefano Babic
This reverts commit 178b8e15ade96c7bd59b9704b91ca51d27c391cd. Patch was merged too fast, without checking that another patch is fixing the reported issue globally - reverted. Signed-off--by: Stefano Babic <sbabic@denx.de>
2013-11-01TI:omap5: Add rdaddr, use consistent loadaddr valuesTom Rini
rdaddr was missing which is a common location for loading ramdisks to. loadaddr was higher than it needs to be, so use the same value other TI platforms use. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01cm_t35: turn on GPIO commandsNikita Kiryanov
Turn on GPIO commands for cm-t35 and cm-t3730. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-11-01cm_t35: reduce default bootdelay to 3 secondsNikita Kiryanov
Current default bootdelay of 10 seconds is too long. Reduce default bootdelay to 3 seconds. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-11-01dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 buildMinal Shah
UART booting is supported on this SoC, but via UART3 rather than UART1. Because of this we must change the board to use UART3 for all console access (only one UART is exposed on this board and a slight HW mod is required to switch UARTs). Signed-off-by: Minal Shah <minal.shah@ti.com> [trini: Make apply to mainline, reword commit] Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01TI:armv7: Change CONFIG_SYS_SPL_ARGS_ADDR to a higher addressTom Rini
With changes to increase the size of the device tree (required to move more data out of the kernel and into DT), loading the args at the old address leads to us overwriting things later on. To correct this, load the args file to where we load the device tree anyhow. This is also safe for non-DT booting as in either case we use r2 to pass in the location of things. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01am335x: Enable CONFIG_OMAP_WATCHDOG supportTom Rini
There is a board-specific portion for calling watchdog enable itself, in main U-Boot. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01tricorder: support 256MiB SDRAM on revision > DAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: read kernel directly from NANDAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: switch to alternative memtestThomas Weber
Increase the tested memory region for mtest and define CONFIG_SYS_MEMTEST_SCRATCH for CONFIG_SYS_ALT_MEMTEST Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: Make u-boot fasterThomas Weber
Silent u-boot and no bootdelay Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: add led supportAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: panic() on unknown boardAndreas Bießmann
Also hang() the board on panic(). Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: add tricordereeprom commandAndreas Bießmann
The new tricordereeprom command can read and write the eeprom for hardware detection on tricorder devices. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: add mtdparts to environmentAndreas Bießmann
Before we always ran 'mtdparts default' which also set the mtdparts and mtdids environment. But if we changed that values by intention we will overwrite them with our default values. This is obviously bad! Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: add cmdline historyAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: use generic provided loadaddrAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: update flash partitioningAndreas Bießmann
The new flash layout respects posible bad blocks in sectors reserved for e.g. SPL, u-boot, kernel, env a.s.o. Additionally this patch prepares for U-Boot Falcon mode for boot time saving. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01tricorder: remove lcdmode from bootargsThomas Weber
Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
2013-11-01arm, da85x: update for the ipam390 boardHeiko Schocher
- switch to correct ecc layout used by the RBL enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC - update default environment - change A2CR to correct value for UART boot mode - adapt cs3cfg timings for nand - change LED bootmode signalization Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-11-01ARM: OMAP4: Convert to ti_armv7_common.hLokesh Vutla
Update omap4_common.h to use ti_armv7_common.h Testing: * Boot tested on OMAP4430 ES2.1 OMAP4460 ES1.1 SDP, OMAP4 PANDA/PANDA ES * Verified ./MAKEALL -s omap Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-11-01OMAP3: igep00x0: rename config file to omap3_igep00x0.hJavier Martinez Canillas
There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEPv2 board and the IGEP COM Module use a TI OMAP35xx/DM37xx processor, is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-11-01ARM: IGEP0033: rename config file to am335x_igep0033.hJavier Martinez Canillas
There seems to be a naming convention for the configuration files for boards using the same SoC family. This makes easier to do changes that affect different boards based on the same SoC. Since the IGEP COM AQUILA use a TI AM335x processor is better to rename its board config to use this naming scheme. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
generated by cgit (git 2.34.1) at 2025-01-02 20:01:31 +0000