| Age | Commit message (Collapse) | Author |
|---|
|
All board configs are now enabled DM_SPI for SPL and
U-Boot proper, so now its time to drop non-dm code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
|
|
Now CONFIG_ATMEL_SPI is defined in Kconfig, so move the
same into defconfig file.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
|
|
This patch add support of hsdk platform-specific commands:
hsdk_clock set - set clock from axi_freq, cpu_freq and tun_freq
environment variables/command line arguments
hsdk_clock get - save clock frequencies to axi_freq, cpu_freq
and tun_freq environment variables
hsdk_clock print - show CPU, AXI, DDR and TUNNEL current
clock frequencies.
hsdk_clock print_all - show all currently used clock frequencies.
hsdk_init - setup board HW in one of pre-defined configuration
(hsdk_hs34 / hsdk_hs36 / hsdk_hs36_ccm / hsdk_hs38 /
hsdk_hs38_ccm / hsdk_hs38x2 / hsdk_hs38x3 / hsdk_hs38x4)
hsdk_go - run baremetal application on hsdk configured
by hsdk_init command.
This patch changes default behaviour of 'bootm' command:
now we are able to set number of CPUs to be kicked by setting
'core_mask' environment variable before 'bootm' command run.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
|
|
|
|
The various load address values are taken from the a37xx configuration
and match the dowstream 'u-boot-2017.03-armada-17.10' release where
appropriate.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.
There are two methods to delivery dtb.
1 Pass from loader:
When u-boot boot from RAM, gdb or loader can pass dtb
via a2 to u-boot dynamically. Of course gdb or loader
shall be in charge of dtb delivery.
2 Configure CONFIG_SYS_FDT_BASE:
It can be configured as RAM or ROM base statically,
no mater u-boot boot from RAM or ROM.
If it was configured as ROM base, dtb can be burned
into ROM(spi flash) by spi driver.
Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
CONFIG_FTSDC010_NUMBER was not used anymore,
can be removed now.
So CONFIG_FTSDC010_NUMBER
can also be removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
|
|
This fixes environment variable location to avoid overlapping with
U-Boot itself. Also more space for environment variables has been
reserved to prevent future issues.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
NXP layerscape platforms like ls1088a, ls2088a
uses MXC I2C Controller.
-Remove dependency of MX6 for the same.
Update related configs to use Kconfig file.
-Add SYS_I2C_MXC_I2C1,_I2C2,_I2C3,_I2C4 in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SPEED,_I2C2_,_I2C3_,_I2C4_ in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SLAVE,_I2C2_,_I2C3_,_I2C4_ in Kconfig
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
|
|
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
|
|
ZynqMP Emulation board is no longer tested and there is no reason to
keep maintaining it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the
accessible DDR address used by alternate memory test.
Before this, 0xfffc0000 address was used, which is the OCM
address and not enabled in MMU table. So, whenever trying
to access 0xfffc0000 address, got Synchronous Abort exception.
After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate
memory test is working fine.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
Enable Driver Model and Device-tree support for omapl138 board
in U-Boot. Also enable DM_SERIAL and DM_I2C.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
commit 1601dd97edc6 ("davinci: omapl138_lcdk: increase PLL0 frequency")
changed the PLL0 frequency to 456MHz, which is needed for the LCDC IP
block. However, in doing so, it caused the PLLOUT clock to be outside
of the allowable specifications given in the OMAP-L138 data sheet. (It
says PLLOUT must be 600MHz max). It also uses a PLLM value outside of
the range given in the TRM (it says PLLM must in the range 0 to 0x1f).
So here is what we have currently:
PLLOUT = 24 / (0 + 1) * (37 + 1) = 912MHz (out of spec)
^ ^ ^
CLKIN PREDIV PLLM (out of spec)
input to PLLDIVn = 912 / (1 + 1) = 456MHz (desired result)
^ ^
PLLOUT POSTDIV
This changes the PLLM value to 18 and the POSTDIV value to 0 so that
PLLOUT is now within specification but we still get the desired
result.
PLLOUT = 24 / (0 + 1) * (18 + 1) = 456MHz (within spec)
^ ^ ^
CLKIN PREDIV PLLM
input to PLLDIVn = 456 / (0 + 1) = 456MHz (desired result)
^ ^
PLLOUT POSTDIV
Fixes: 1601dd97edc6 ("davinci: omapl138_lcdk: increase PLL0 frequency")
Signed-off-by: David Lechner <david@lechnology.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add configurations for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch enables ethernet support for ls1012ardb.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
Fix NOR, SD and QSPI fallback option in case of secure boot failure.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.
Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
(DISTRO activated)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Support several pixel format (8bits, 16bits, 24bits & 32bits).
Add new file st_logo_data.h which contains logo
stmicroelectronics_uboot_logo_8bit_rle.bmp.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
|
|
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch updates the default u-boot env for K2L HS devices
to install the secure boot monitor and load the fitImage during
boot.
Signed-off-by: Madan Srinivas <madans@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The kernel size is getting bigger and bigger. Because the Android
common kernel is even bigger than the vanilla one, so images overlap
in the current memory layout.
Adjust the load address for a bigger kernel image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
If a bigger EL32 is used, fip.bin can be larger than the currently
assumed boot firmware size. Adjust the update commands.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
This commit does the following for OMAP3 EVM:
- Track omap3_beagle changes where possible
- Remove CONFIG_SYS_MPUCLK and CONFIG_MTD which are not needed for the
default board configuration to work.
- Remove CONFIG_SPL_SYS_MALLOC_SIMPLE and CONFIG_SYS_MALLOC_F_LEN from
default config. CONFIG_SYS_MALLOC_F_LEN=0x400 is set by configuration
automatically. [allows board to boot with SERIAL_SEARCH_ALL=y]
- Use updated NAND layout:
device nand0 <omap2-nand.0>, # parts = 6
#: name size offset
-------------------------------------------------
0: spl 0x00080000(512k) 0x00000000
1: u-boot 0x001e0000(1920k) 0x00080000
2: u-boot-env 0x00020000(128k) 0x00260000
3: dtb 0x00020000(128k) 0x00280000
4: kernel 0x00600000(6m) 0x002a0000
5: rootfs 0x0f760000(-) 0x008a0000
-------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
This commit does the following for BeagleBoard{-xM}:
- Enable DM_SERIAL which also enables SPL_DM_SERIAL
- Misc. config updates in support of DM_SERIAL
- Use updated NAND layout (BeagleBoard):
device nand0 <omap2-nand.0>, # parts = 6
#: name size offset
-------------------------------------------------
0: spl 0x00080000(512k) 0x00000000
1: u-boot 0x001e0000(1920k) 0x00080000
2: u-boot-env 0x00020000(128k) 0x00260000
3: dtb 0x00020000(128k) 0x00280000
4: kernel 0x00600000(6m) 0x002a0000
5: rootfs 0x0f760000(-) 0x008a0000
-------------------------------------------------
- Use MMC and UBIFS support from config_distro_bootcmd.h
- Use LEGACY_MMC and NAND support defined in omap3_beagle.h
[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-mmc-fat
label omap3-beagle-mmc-fat
kernel /zImage
fdt /omap3-beagle.dtb
append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
[LEGACY_MMC(0:2)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-mmc-ext4
label omap3-beagle-mmc-ext4
kernel /boot/zImage
fdt /boot/omap3-beagle.dtb
append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
[UBIFS(ubi0:rootfs)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-nand-ubifs
label omap3-beagle-nand-ubifs
kernel /boot/zImage
fdt /boot/omap3-beagle.dtb
append console=ttyO2,115200n8 root=ubi0:rootfs rw ubi.mtd=rootfs rootfstype=ubifs rootwait
---8<-------------------------------------------------------------------
The board's 'bootcmd' can also be overridden with:
CONFIG_BOOTCOMMAND="run findfdt; run mmcboot"
CONFIG_BOOTCOMMAND="run findfdt; run nandboot"
CONFIG_BOOTCOMMAND="run findfdt; run ramboot"
or
CONFIG_BOOTCOMMAND="run findfdt; run somethingelse"
The use of 'run findfdt' is required.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Booting a aarch64 Linux kernel requires the image to be placed
text_offset bytes from a 2MB aligned address.
See https://www.kernel.org/doc/Documentation/arm64/booting.txt
booti_setup() takes care about this alignment and will relocate the
image if not properly aligned with memmove(). This can require up
to double the size of the loaded image and therefore accidentally
overwrite content placed there (i.e ramdisk_addr_r) for large kernel
images.
By adding text_offset to the default kernel_addr_r we can prevent that
from happening for kernels larger 18MB and also save a few cycles.
We can assume a text_offset of 0x80000 for most cases, all others will be
handled by booti_setup() anyway.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).
Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.
After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.
- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.
- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.
After the changes the suspicious defconfigs passes building.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AT91SAM9263EK
CONFIG_AT91SAM9RLEK
CONFIG_BARIX_IPAM390
CONFIG_BOARD_H2200
CONFIG_EP9301
CONFIG_KZM_A9_GT
CONFIG_PICOSAM
CONFIG_PLATINUM_PICON
CONFIG_PLATINUM_TITANIUM
CONFIG_PM9261
CONFIG_PM9263
CONFIG_PM9G45
CONFIG_SIEMENS_DRACO
CONFIG_SIEMENS_PXM2
CONFIG_SIEMENS_RUT
CONFIG_SMDKC100
CONFIG_SMDKV310
CONFIG_STM32F4DISCOVERY
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_ARM926EJS
CONFIG_CPUAT91
CONFIG_EXYNOS5800
CONFIG_SYS_CORTEX_R4
Most of them are config symbols named after the respective SoCs which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
