| Age | Commit message (Collapse) | Author |
|---|
|
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
|
|
This patch replaces not existing addr_uboot environment variable by
loadaddr at get_uboot_net and burn_uboot_xxx commands. Otherwise these
commands are broken.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
|
|
Add USB XHCI support for ls2085rdb platform
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add USB XHCI support for ls2085qds platform
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Enable bootscript support in secure boot for establishing
chain of trust on LS1021atwr.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
For ls1021a, Reserve secure code in to memory in case OCRAM
is needed by other usage.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
i.MX6UL's DRAM space starts from 0x80000000, same to i.MX6SX, so use
same address with i.MX6SX.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
DRAM space starts from 0x80000000 for i.MX6UL, so need to
fix LOADADDR, SYS_TEXT_BASE.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
Since i.MX6UL use A7 core, but not A9 core, we do not need
the erratas for i.MX6UL.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Add Kconfig options for USB keyboard and use them for cm-fx6.
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb
config to defconfig.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Move CONFIG_CMD_* options that can be selected in menuconfig to cm-fx6
defconfig.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Implement a cm-fx6 specific board_video_skip() to provide the option to not
initialize the display.
The new function does not init display if the environment variable "panel" is
not defined, or if it is set to an unsupported value.
Collateral changes:
- Don't use the global displays array (it's CONFIG_IMX_VIDEO_SKIP specific).
- Don't use detect_hdmi(), since env controlled init makes it unnecessary.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
Build target: mx6qpsabreauto_config
Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
PMIC: PFUZE100 ID=0x10
Flash: 32 MiB
NAND: 0 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Detect the SOC and board variant at runtime and change the dtb name,
but not hardcoding the fdt_file env variable.
Take the following patch as a reference.
Íd58699b157df75f1aa0b363ea9c21add21a0c
"mx6cuboxi: Load the correct 'fdtfile' variable"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
|
|
Add support for NOR flash and GPIO/I2C switch control on RevC.
- NOR support
- bank0/bank4 switch
- SD/eMMC switch
- board version
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
For running Chain of Trust when doing Secure Boot from NAND,
the Bootscript header and bootscript must be copied from NAND
to RAM(DDR).
The addresses and commands for the same have been defined.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
IFC nand ecc encode and decode mode are not correctly
set in CSOR register during nand initialization.Enable
ecc encode/decode in 4-bit mode
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
T1040D4RDB is re-designed T1040RDB board with following changes :
- Support of DDR4 memory
- Support of 0x66 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
- Support of QE-TDM
Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
- Support of DDR4 memory
- Support for 0x86 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
- Support of DIU
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.
With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
ARMv8 requires an architected timer to be present, so it can be used
instead of the Tegra US timer. This allows for better code reuse.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
For 64-bit ARM SoCs we rely on non-U-Boot code to bring up the CPU in
AArch64 mode so that we don't need the SPL. Non-cached memory is not
implemented (yet) for 64-bit ARM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
|
|
Enable SATA for the ZynqMP targets.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Wire up ethernet controllers and enable MII and BOOTP options.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add xm011 DTS file and related configs and configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Provide option to enable uart dcc support for zynqmp
This config can be enabled as per board config file.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Move CONFIG_SYS_TEXT_BASE of ZynqMP_ep to its
respective defconfig
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
We are getting very close to running out of space in SPL, and with the
currently Chrome OS gcc 4.9 we exceed the limit. Add a litle more space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Enable DTS support (CONFIG_OF_LIBFDT) and select
CONFIG_FIT in defconfig.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
using http://git.ti.com/keystone-linux/boot-monitor/trees/master as
reference (tag K2_BM_15.07) the generated files do not have evm
extensions by default. So dont use -evm extension.
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Switch to using zImage instead of uImage. and while at it, start using
bootz as default. While at it, get rid of BOOTIMAGE define and start
using Linux upstream dtb file names.
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Use the defaults defined in DEFAULT_LINUX_BOOT_ENV
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Try to maintain as much commonality by conditionally including stuff
in armv7_common as necessary and removing the common defines from
keystone2 header.
Note: as part of this change, all keystone2 platforms will now start
using the generic u-boot prompt instead of the custom prompt.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
rename the keystone2 common header into an keystone2 architecture
specific header which can then reuse the common ti_armv7 config headers.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
CONFIG_LINUX_BOOT_PARAM_ADDR is not a valid configuration option. Do
just like what the rest of the world does.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Commit bd2c4522c26d5 ("ti: armv7: enable EXT support in SPL (using
ti_armv7_common.h)") enabled thumb mode only for SPL builds, however,
All TI armv7 platforms do support thumb, and there is no reason why the
space savings cannot be exploited for u-boot as well.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.
Many of the options are architecture specific, however a lot are common
with v7 architecture. So, step 1 will be to move out OMAP specific stuff
from ti_armv7_common into a ti_armv7_omap.h header which is then used
by all the relevant architecture headers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
CONFIG_MUSB_HDC should be CONFIG_MUSB_HCD to have any effect.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
Gumstix is migrating from ext3 to ext4 file system.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
|
