| Age | Commit message (Collapse) | Author |
|---|
|
The device tree already contains the required configuration for both the
USB1 and USB3 ports. Enable the required configuration options to enable
both these ports, which in turn allows the USB1 port to be used.
Note that on a true Seaboard, this port is typically used as a device
port hosting Tegra's USB recovery protocol. However, on the Springbank
derivative, this port is the only external USB port, so we enable it as
a host port so that USB peripherals may be used. Enabling this port in
U-Boot as a host port doesn't prevent the port from reverting to a
device port when the CPU is reset into recovery mode.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.
* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Currently, Tegra's default environment uses non-standard variables to define
where boot scripts should load the kernel, FDT, and initrd. This change both
changes the variable names to match those described in U-Boot's README, and
shuffles their values around a little so that the values make a little more
sense; see comments in the patch for rationale behind the values chosen.
Note that this patch does remove the old non-standard variable "fdt_load" from
the default environment, so this patch requires people to change their boot
scripts.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This define indicates the size of the memory region where it is safe
to place data passed to the Linux kernel (ATAGs, DTB, initrd). The
value needs to be:
a) Less than or equal to RAM size.
b) Small enough that the area is not within the kernel's highmem region,
since the kernel cannot access ATAGs/DTB/initrd from highmem.
c) Large enough to hold the kernel+DTB+initrd.
256M seems large enough for (c) in most circumstances, and small enough
to satisfy (a) and (b) across any possible Tegra board. Note that the
user can override this value via environment variable "bootm_mapsize"
if needed.
The advantage of defining BOOTMAPSZ is that we no longer need to define
variable fdt_high in the default environment. Previously, we defined
this to prevent the DTB from being relocated to the very end of RAM,
which on most Tegra systems is within highmem, and hence which would
cause boot failures. A user can still define this variable themselves
if they want the FDT to be either left in-place wherever loaded, or
copied to some other specific location. Similarly, there should no
longer be a strict requirement for the user to define initrd_high if
using an initrd.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This adds board support for the Toradex Colibri T20 module.
Working functions:
- SD card boot
- USB boot
- Network
- NAND environment
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
|
This patch remove the env saving in NAND as so far the
NAND driver is not ported to the M54418TWR platform.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
|
|
|
|
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
|
|
|
|
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.
Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
|
|
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define. Finally, enable the options on the am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add video support to the board with the display
focaltech etm070003dh6.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Some GPIOs differ in the new revision board.
Previous revision are considered obsolete and
they will not anymore supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
The mcx board was slightly modified and the pinmux must be updated.
There is no need to support the old board, that becomes obsolete.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
Add support for the new kmvect1 board powered by the mpc8309 processor.
As this board is very similar to the existing suvd3, instead of adding a
new config header file, just add a new config option to suvd3.h
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Neither cm-t35, nor cm-t3730 is using OneNAND or flash.
Remove the related defines from config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Fix usage of 'mmc rescan' by many configs. Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device. 'mmc rescan' itself does not take any arguments.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
|
|
|
|
|
|
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
The P5040 does not have SRIO, so don't put the SRIO definitions in
corenet_ds.h. They belong in the board-specific header files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Enable Coreboot and EXT4 Filesystems on the coreboot board.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some of the boards still used the old PXA_MMC driver instead of the
new generic one. Use the new one instead so the old can be removed
and the generic MMC framework can be properly used.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Flip the boards to use the generic bounce buffer instead of the
MMC one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Data cache and CONFIG_MMC_BOUNCE_BUFFER can be safely enabled now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Data cache and CONFIG_MMC_BOUNCE_BUFFER can be safely enabled now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Use internal RAM for stack pointer as it is done in other i.MX boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Conflicts:
drivers/serial/serial_lh7a40x.c
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch provides a support to use buffered writes on flash
for versatile and vexpress boards.
This will certainly increase the flash writes.
Signed-off-by: Jagannadha Sutradharudu Teki <402jagan@gmail.com>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
|
|
The sbc8548/60 (both similar, just variations in UART hardware)
support has been removed from the linux kernel as of v3.6-rc1~132
so lets also now remove it from the u-boot tree as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The recent U-Boot version 2012.07 has improved drivers
(e.g. MMC and network/FEC) regarding DCache handling.
So it should be safe to use the DCache on the i.MX6, now.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
mx53evk has only one Ethernet port, so remove CONFIG_HAS_ETH1 option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx51evk has only one Ethernet port, so remove CONFIG_HAS_ETH1 option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx53loco has only one Ethernet port, so remove CONFIG_HAS_ETH1 option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Since PLL2 now has changed, it is necessary to adapt the CONFIG_IPUV3_CLK
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
|
|
|
|
move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created
ide_init_postreset() (invoked after calling ide_reset after ide_preinit),
some cleanup to make checkpatch happy, enable IDE init hooks in configs of
affected boards.
confusingly, these hooks are used by more than just mpc8xx-based boards, and
therefore are placed in arch/ppc/lib/
note: checkpatch still emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
|
|
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
