| Age | Commit message (Collapse) | Author |
|---|
|
Previously we had stored the environment right after the
u-boot.img on the disk. I never liked this because with dtbs
being included and such the image could grow in size. Instead
we move the environment to be negatively offset from the 1MB
mark. Almost all our images start at 4MB's, and most standard
images start at 1MB, and all our storage devices are a minimum
1MB. Therefore we can store env there for all classes of devices
and have plenty of space in case u-boot.img needs to grow.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Mainline and now the SolidRun 4.9 nxp based tree use the new
reorganization of device-tree files that separate out the emmc
into its own dtb. u-boot will now look for -emmc in the device
tree name if one is detected.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
This macro is not used.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Add support for the Colibri iMX6ULL module which comes with
on-board raw NAND.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Currently the fdtfile environment variable is set to
CONFIG_DEFAULT_DEVICE_TREE which is Ñ–nternally used as U-Boot devicetree
source. The OS can use a different filename and Kconfig gives us the
ability to select a default devicetree via CONFIG_DEFAULT_FDT_FILE.
This also gives user configuring U-Boot via menuconfig the behaviour
someone would expect.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The first dhcp command consistently fails with a timeout when
the lion-rk3368 board is connected to a Zyxel GS1100-24E
Gigabit Ethernet switch:
ethernet@ff290000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Increasing PHY_ANEG_TIMEOUT from the default 4000 to 8000 makes the
first dhcp command work reliably.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
With this commit we do:
- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.
- move CONFIG_BOOTCOMMAND from header file to defconfig
- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).
- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.
- make space for the cfgscr within mtdparts on brppt1_nand
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.
In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
|
|
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Mini targets are using different ENV_SIZE then standard one that's why
defconfigs should be updated to simplify config files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Simplify zynq_cse config by setting up ENV_SIZE via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch added support to enable CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET
and CONFIG_ENV_SECT_SIZE through Kconfig for Zynq and Zynqmp.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Remove the SDRAM_BASE and SDRAM_SIZE as it can now get these
details from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
XILINX_SPI_FLASH_BASEADDR logic has been converted to DM that's why
there is no reason to depend on this address anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
These macros are not required anymore. These will be taken from
configuration file.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no reason to keep these configs in platform config file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no reason to define default option for this macro which is
already done in common/cli_hush.c.
86 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
87 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
88 #endif
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add build support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Conflicts:
arch/arm/Kconfig
arch/arm/mach-socfpga/Kconfig
|
|
This patch moves CONFIG_MP to Kconfig
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Newer kernels have moved from ttyO0 to ttyS0, and when booting
it drops a notice:
WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
This ensures that you still see kernel messages. Please
update your kernel commandline.
This patch updates the console to use ttyS0 and eliminate the
chatter.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
|
|
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
|
|
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The ax25-ae350 target currently uses CONFIG_BOOTP_SERVERIP which means we
ignore the DHCP provided TFTP ip address. This breaks every case where we
do now provide a serverip environment variable.
Instead, let's use the new CONFIG_BOOT_PREFER_SERVERIP option to fall back
to the DHCP provided TFTP IP if no serverip environment variable is set.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Rick Chen <rick@andestech.com>
|
|
|
|
For boards that don't route serial port pins out, it's quite common
to attach a USB keyboard as the input device, along with a monitor.
However USB is not automatically started in the generic efi payload
codes. This uses a payload specific last_stage_init() to start the
USB bus, so that a USB keyboard can be used on the U-Boot shell.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add USB as boot target depending on the configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
BOOT2 partition is empty and free for using to store the environment.
Use that instead of the default user partition.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
This adds DM_GPIO support for the davinici GPIO driver with
DT support.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
|
|
|
|
In order to properly detect the board the checks need to be done
in a specific order. Move these tests back into a single enum
function that will always return the proper the board it is checking.
This also adds the best test we have for detecting the rev 1.5 som,
and it simplifies the device-tree filename building.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Disable console output by default on imx53 based boards from
K+P.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Since kernel commit 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate
into cpu and baseboard dts") the dtb name has changed.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
We should use the baudrate variable available inside U-Boot
environment to allow it to be changed dynamically.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
If GPT gets broken, then after N boot attempts we will run the SWUpdate
restoration image.
On its enter we will check GPT and restore it if needed.
To test it:
display5 > mmc write 0x12000000 4 8
It will overwrite the primary GPT table.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
After moving to swupdate 2017.07, the default fs for swupdate rootfs
is ext4, not ext3.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
