summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2019-10-30Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- H6 dts(i) sync (Clément) - H6 PIO (Icenowy) - Fix pll1 clock calculation (Stefan) - H6 dram, half DQ (Jernej) - A64 OLinuXino eMMC (Sunil)
2019-10-25Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mipsTom Rini
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs - bmips: various small fixes - mtmips: add new drivers for clock, reset-controller and pinctrl - mtmips: add support for high speed UART - mtmips: update/enhance drivers for SPI and ethernet - mtmips: add support for MMC
2019-10-25Merge tag 'xilinx-for-v2020.01-part2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 part 2 common: - Fix manual relocation for repeatable commands arm: - Also clean up generated dtbos microblaze: - Add support for Manual relocation in crypto framework - Tune and align architecture bootm support zynq: - DT sync ups - Some defconfig updates - Remove empty board_early_init_f() zynqmp: - Clean firmware handing via drivers/firmware/ - DT/defconfig name alignments - DT cleanups with using firmware based clock driver - Some defconfig updates - Add IIO ina226 DT description - Tune zynqmp_psu_init_minimalize.sh script - Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216 versal: - Clean firmware handing via drivers/firmware/ - Add gpio support - Enable DT overlay/USB/CLK/FPGA - DT updates - Tune mini configuration spi: - gqspi - Remove unused headers
2019-10-25mips: mtmips: change baudrate table for all boardsWeijie Gao
This patch changes baudrate table for all boards preparing for using mtk highspeed uart driver. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25bmips: configs: switch to size definitionsÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-25mips: bmips: remove unneeded definitionsÁlvaro Fernández Rojas
These are no longer needed. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-25bmips: enable vr-3032u nand supportÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTDFrieder Schrempf
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in SPL. They often rely on hacks in the board header files to include this option conditionally. To be able to fix this, we previously introduced a separate option SPL_SPI_FLASH_MTD. Therefore we can now adjust the Makefile and change the code in sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD). We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the header files to the according defconfigs. The affected boards are socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6 and da850evm. We do this all in one patch to guarantee bisectibility. This change was tested with buildman to make sure it does not introduce any regressions by comparing the resulting binary sizes. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-24Merge branch '2019-10-24-UFS-support'Tom Rini
- Add Universal Flash Storage (UFS) support
2019-10-24ARM: zynq: Move BOOTM_NETBSD to KconfigMichal Simek
The commit 4b0bcfa7c4ec ("Kconfig: Migrate CONFIG_BOOTM_* options") moved BOOTM_ options to Kconfig that's why align zynq defconfig with it. Disabling NETBSD was done by commit d6f48ea5ce18 ("ARM: zynq: Do not enable NETBSD support by default"). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Add support for HyperBus Memory Controller of TI's J721e and AM654 SoCs (Vignesh)
2019-10-24configs: j721e_evm.h: Define CONFIG_SYS_MAX_FLASH_BANKS_DETECTVignesh Raghavendra
Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks are automatically detected by CFI flash driver Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-23env: ti: Add environment variables to boot from UFSFaiz Abbas
Add environment variables to boot kernel from a filesystem contained in the 2nd UFS LUN. The user can boot from a ufs filesystem just by entering the following commands. => setenv boot ufs => boot Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23Merge tag 'u-boot-stm32-2019-10-23' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Disable CONFIG_NET flag for MCU STM32 - Fix ramdisk_addr_r for stm32f746-disco - Fix USB product id for stm32mp1
2019-10-22configs: stm32f746-disco: Fix ramdisk_addr_rPatrice Chotard
Set ramdisk_addr_r to 0xC0600000. Reported-by: Christophe Priouzeau <christophe.priouzeau@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-21configs: ls1012afrwy: Add CONFIG_ENV_ADDRKuldeep Singh
This configuration enables picking the environment from flash before DDR init. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-21configs: ls1012ardb: Add CONFIG_ENV_ADDRKuldeep Singh
CONFIG_ENV_ADDR config option enables picking the environment from flash before DDR init. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-18configs: sei610: Add config file to fix userdata sizeGuillaume La Roque
Add separate config file to handle the different eMMC size on the sei610 board. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18configs: sei510: rework header and fix userdata sizeGuillaume La Roque
Move android generic config and boot sequence in meson64_android header and fix size of userdata to use all eMMC on SEI510. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18configs: sei510: enable Video Display supportNeil Armstrong
Add the necessary config options to support BMP display over HDMI, and add a preboot command to load the BMP file from a predefined eMMC partition. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-16arm: remove the H2200 boardHeinrich Schuchardt
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y. The maintainer Lukasz Dalek suggested to remove the board. https://lists.denx.de/pipermail/u-boot/2019-August/380685.html Cc: Lukasz Dalek <luk0104@gmail.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> [trini: As this is the last non-toradex PXA board, update travis too] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-14Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- vining_fpga updates
2019-10-14Merge tag 'u-boot-imx-20191014' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191014 ------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628 - logicpd pinmux - i.MX7ULP: imx_ddr_size - fixes Toradex i.MX6/i.MX7 - pico-imx7d - tpc70 converted to DM - New Board: meerkat96 - add HAB version command - i.MX8 : imx8: Jump from alias to OCRAM address at SPL init imx8qm/qxp: Set SPL TEXT base to OCRAM base
2019-10-13stm32mp1: configs: update videoYannick Fertré
Update video configs to support bitmap 16bpp, 24bpp, 32bpp & RLE8. Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-10-13colibri_imx7: remove legacy sdboot wrapperIgor Opaniuk
Remove legacy sdboot wrapper as distroboot can be used instead. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-10-13colibri_imx6: remove legacy sdboot wrapperIgor Opaniuk
Remove legacy sdboot wrapper as distroboot can be used instead. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-10-13colibri-imx6ull: remove legacy sdboot wrapperIgor Opaniuk
Remove legacy sdboot wrapper as distroboot can be used instead. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-10-13apalis_imx6: remove legacy sdboot wrapperIgor Opaniuk
Remove legacy sdboot wrapper as distroboot can be used instead. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-10-13imx8qm/qxp: Set SPL TEXT base to OCRAM baseYe Li
Modify the SPL TEXT base from OCRAM alias to OCRAM base 0x100000, so we can use full OCRAM not limit to 96KB Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-13imx: config: Update KP's TPC70 config to support SWUpdateLukasz Majewski
This patch updates envs responsible for using USB pendrive as a SWUpdate based tool for recovery and update. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: Convert TPC70 (imx6q) board to use DM/DTS in SPL and u-bootLukasz Majewski
This patch converts the TPC70 to use driver model and device tree description in both SPL and u-boot proper. Notable changes (DM/DTS conversion): - PINCTRL{_IMX6} - DM_I2C - enable 'regulator' and 'pmic' commands - DM_MMC and BLK (USDHC) - DM_ETH - DM WDT (including SYSRESET) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: config: Update TPC70 config to support eMMC's boot0 SPL updateLukasz Majewski
The TPC70 can boot from eMMC's boot0. This patch allows it to update this HW partition's SPL. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: config: Add script commands to update u-boot and OE's wicLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13pico-imx7d: Support distro boot for FIT image caseJun Nie
Support distro boot for pico imx7d in FIT image case. Signed-off-by: Jun Nie <jun.nie@linaro.org> Tested-by: Joris Offouga <offougajoris@gmail.com>
2019-10-13board: tbs2910: Convert eth to driver modelSoeren Moch
So we can remove lots of legacy config code. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13mx6: mx6sabre common: Use more conventional spelling of fdtfileSjoerd Simons
Both the distro boot configuration as well as the general pxe support standardized on fdtfile as the variable to hold the dtb filename. Adjust to follow that such that e.g. "pxe boot" will just work. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2019-10-13Add i.MX7D based Meerkat96 board supportShawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-11tao3530: Fix usage of mmc rescanJarkko Nikula
Currently "bootcmd" does not work as intended but instead prints MMC usage information and goes directly to "nandboot". Follow what the commit 669681104daa ("configs: Fix usage of mmc rescan") does for other boards prior to support for TechNexion TAO3530 SoM was added. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
2019-10-11configs: ti: Use addr_fit for run_fit environment variableAndrew F. Davis
When running 'run_fit' the FIT file should have been loaded at 'addr_fit', although at this point they should be the same use this variable instead of 'loadaddr'. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-10-11am335x, guardian: adapt guardian board to DMMoses Christopher
- update partition table - remove env partitions - dts: add new interfaces (uart2, extra gpio-key) remove unneeded entries update nand timings for performance improvement - defconfig: adapt configurations to suit DM remove unneeded configs - am335x_guardian.h: remove mmc boot Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11env: ti: am65x_evm: Add env support to boot the MCU R5F rprocsSuman Anna
Add support to boot the MCU domain R5F Core0 remoteproc at U-boot prompt on the AM65x EVM boards by using the 'boot_rprocs' and other env variables defined in the common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS' macro. The default configuration is to use the MCU R5F in Split mode, so both the R5F Core0 and Core1 are started before loading and booting the Linux kernel using the following firmware: MCU R5FSS0 Core0 (Split) : 0 /lib/firmware/am65x-mcu-r5f0_0-fw MCU R5FSS0 Core1 (Split) : 1 /lib/firmware/am65x-mcu-r5f0_1-fw The MCU R5FSS was initially running the R5 SPL in LockStep mode with ATCM disabled, and is actually shutdown to enable it to be reconfigured and booted by either A53 U-Boot or Linux kernel in remoteproc mode and using ATCM. The MCU R5FSS would need to be reconfigured for Lockstep mode through DT if a fault-tolerant/safety application were to be run on the cluster with the DEFAULT_RPROCS macro updated to remove the Core1 firmware. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11env: ti: j721e-evm: Add support to boot rprocs including R5Fs and DSPsSuman Anna
Add support to boot some remoteprocs at U-boot prompt on the J721E EVM boards by using the 'boot_rprocs' and other env variables defined in the common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS' macro. The list of R5F cores to be started before loading and booting the Linux kernel are as follows, and in this order: Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7-main-r5f0_1-fw Main R5FSS1 (LockStep) : 4 /lib/firmware/j7-main-r5f1_0-fw The MCU R5FSS0 and Main R5FSS1 are currently in LockStep mode, so the equivalent Core1 rprocs (rproc #1 and #5) are not included. The Main R5FSS0 Core0 (rproc #2) is already started by R5 SPL, so is not included in the list either. The DSP cores are started in the following order before loading and booting the Linux kernel: C66_0: 6 /lib/firmware/j7-c66_0-fw C66_1: 7 /lib/firmware/j7-c66_1-fw C71_0: 8 /lib/firmware/j7-c71_0-fw The order of the rprocs to boot can be changed at runtime if desired by overwriting the 'rproc_fw_binaries' environment variable at U-boot prompt. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-09ARM: socfpga: vining_fpga: Update environmentMarek Vasut
Update board environment to match the one used in deployment. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09ARM: socfpga: vining_fpga: Rename VINING|FPGAMarek Vasut
The company Samtec was merged into Softing, migrate the board over to the new name and update copyright headers. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09Merge tag 'xilinx-for-v2020.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
2019-10-09Merge tag 'u-boot-imx-20191009' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191009 ------------------- Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532 - MX6UL / ULZ - Toradex board - Allow to set OCRAM for MX6Q/D - MX7ULP - MX8: (container image, imx8mq_mek), SCU API - fix several board booting from SD/EMMC (cubox-i for example) - pico boards [trini: display5 merged manually] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Move WATCHDOG_TIMEOUT_MSECS to Kconfig (Heiko)
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Rename existing FSP code to fsp1 - Add fsp2 directory in preparation to support FSP 2.0 - Various x86 platform codes update - Various bug fixes and updates in dm core, sandbox and spl
2019-10-08pico-imx7d: fix splash logo drawingJoris Offouga
Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08apalis_imx6: use distroboot by defaultIgor Opaniuk
Use distro_bootcmd as default bootcmd instead of legacy wrappers. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
generated by cgit (git 2.34.1) at 2025-01-10 07:24:08 +0000