summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2012-07-07arm/km: cleanup km_kirkwood boardsHolger Brunck
Remove config options from boards.cfg and simply add one switch per board and differ afterwards in km_kirkwood.h between the features. More boards are upcoming and therefore it's easier to have this at one place. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: enable BOCO2 FPGA download supportValentin Longchamp
This adds a first support of the FPGA download for a PCIe FPGA based on the BOCO2 CPLD. This takes place in 3 steps, all done accessing the SPICTRL reg of the BOCO2: 1) start the FPGA config with an access to the FPGA_PROG bit 2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1 for the end of the FPGA configuration (with a timeout) 3) reset the FPGA 4) finally remove the access to its config EEPROM from the FPGA so that the CPU can update the FPGA configuration when the kernel is running The boards with a PCIe FPGA but without BOCO2 still are supported. The config option name is CONFIG_KM_FPGA_CONFIG Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: remove portl2.h and use km_kirkwood insteadHolger Brunck
The additional headerfile is unneeded here, we can use the generic km_kirkwood.h instead. And we can use the better config option KM_PIGGY4_88E6061 for the specific features for boards with this design in km_arm.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: convert mgcoge3un target to km_kirkwoodHolger Brunck
Use the generic header km_kirkwood.h and get rid of the board specific header. changes for v2: rebased because of changes in other patches Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add kmcoge5un board supportHolger Brunck
For u-boot this board is similar to mgcoge3un. But some differences are present. We have a different SDRAM on it and therefore a new SDRAM config file. Additionaly this board has a direct MAC/MAC connection from the kirkwood to a marvell simple switch without a phy inbetween, this needs a new configuration for the mvgbe driver. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add kmnusa board supportHolger Brunck
This board is similar to portl2, but it has the u-boot environment in a SPI NOR flash and not in an i2c eeprom like portl2 have. Some other details: - IVM EEPROM is at adress: pca9547:70:9 - PCI is enabled - PIGGY4 is connected via MV88E6352 simple switch. There is no phy between the simple switch and the kirkwood. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07cm-t35: fix incorrect NAND_ECC layout selectionNikita Kiryanov
The current configuration selects an incorrect NAND ECC layout, which causes u-boot to write HW ECC data incorrectly. This patch selects the right layout. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2012-07-07ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.SRICHARAN R
Currently on OMAP4/5 platforms, many kernel drivers are dependent upon the bootloaders for mux, dpll and clock configurations. This should not be the case and bootloaders should set only the minimum required for the uboot functionality and kernel boot. Note that this is going to break the kernel drivers. But this is the only way to get things fixed in the kernel. Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07Kirkwood: Add support for Ka-Ro TK71Marek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Wolfgang Denk <wd@denx.de>
2012-07-07arm/km: use spi claim bus to switch between SPI and NANDValentin Longchamp
We overwrite these weak functions from the kirkwood spi code to use our own method to be able to switch between the SPI NOR and the NAND flash. This is needed e.g. to update the u-boot. The former command do_spi_toggle can therefore be removed. And the usage of this command is removed from the u-boot update command in the u-boot environment. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2Simon Guinot
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2012-07-07lacie_kw: fix SDRAM banks number for net2big_v2Simon Guinot
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2012-07-07Kirkwood: add lschlv2 and lsxhl board supportMichael Walle
This patch adds support for both the Linkstation Live (LS-CHLv2) and Linkstation Pro (LS-XHL) by Buffalo. Signed-off-by: Michael Walle <michael@walle.cc> Cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07km_arm: use filesize for erase in update commandValentin Longchamp
We used to have an arbitrary value, which can be a problem if we have a u-boot image that is bigger than this value. This patch is dependant on the whole km/arm series and will be included in the v3 of the series if there is one. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: enable mii cmdValentin Longchamp
This is useful to debug the switch initialization Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: remove CONFIG_RESET_PHY_RHolger Brunck
This is already defined in the generic kirkwood header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATEHolger Brunck
This config option sounds like the it is responsible for the update of the environment, but it is the u-boot update handling. Therefore we adapt it to a more apropriate naming. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add piggy mac adress offset for mgcoge3unHolger Brunck
On mgcoge3un the piggy mac adress is at offset 3. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add board type to boards.cfgHolger Brunck
Some other kirkwood boards from keymile will follow. They will have some small differences, but we want to use the km_kirkwood.h for all to distinguish them. This patch a preparation for this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07AT91SAM9*: Change kernel address in dataflash to match u-boot's sizeAlexandre Belloni
On at91sam platforms, u-boot grew larger than the allocated size in dataflash, the layout was: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00042000 fs 0x00252000 u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 = 0x39C00 bytes anymore. Now, the layout is: bootstrap 0x00000000 ubootenv 0x00004200 uboot 0x00008400 kernel 0x00084000 fs 0x00294000 Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07AT91: at91sam9m10g45ek : Enable EHCI instead OHCIBo Shen
Enable EHCI support instead OHCI Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07Fix: AT91SAM9263 nor flash usageesw@bus-elektronik.de
Fix: board doesn't boot from norflash Fix: environment can't write to flash (end address/start address not on sector boundary) Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07mx53smd: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53loco: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53evk: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53ard: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definitionFabio Estevam
According to include/i2c.h: "/* * Many boards/controllers/drivers don't support an I2C slave interface so * provide a default slave address for them for use in common code. A real * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does * support a slave interface. */ #ifndef CONFIG_SYS_I2C_SLAVE #define CONFIG_SYS_I2C_SLAVE 0xfe #endif " As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx53ard: Remove unused CONFIG_MII_GASKETFabio Estevam
CONFIG_MII_GASKET is not defined anywhere, so remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07m28evk: use same notation to alloc the 128kB stackOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Wolfgang Denk <wd@denx.de>
2012-07-07m28evk: drop duplicated definition of CONFIG_OF_LIBFDTOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07mx28evk: fix board config include guardian macro nameOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07mx28evk: ensure command definition is in alphabetic orderOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07m28evk: fix board config include guardian macro nameOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
2012-07-07mx53loco: Fix revision of Dialog boardsFabio Estevam
Original code was assuming that the fuse revision version for all mx53loco boards based on Dialog PMIC was the same, which is not the case. Force the revision of all Dialog-based boards to 0. This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel for Dialog rev E boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07cm-t35: reduce the environment sizeIgor Grinberg
Reduce the environment size (128KB => 16KB) to improve the environment operations time (e.g. reading, ecc calculation). Also, remove the unused CONFIG_SYS_ENV_SECT_SIZE. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07omap3evm: Add CONFIG_CMD_ASKENVTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07omap3_beagle: Add CONFIG_CMD_ASKENVTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07omap3evm: Set BOOTDELAY to 3Tom Rini
We reduce the bootdelay from 10s to 3s to give users a short but usable window to interrupt the boot process if needed. Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07OMAP3 Beagle: Set BOOTDELAY to 3Tom Rini
We change the bootdelay to give users a little bit longer to break in if needed. Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07arm,davinci: update for enbw_cmc boardHeiko Schocher
- change gpio pin settings: - gpio pin 6[13] (PLC reset) default value low - gpio pin 6[0] (TPM reset) default value low - 4 new GPIO pins pin i/o name - 3[9] input Board Type - 2[7] input HW-ID0 - 2[6] input HW-ID1 - 2[3] input HW-ID2 - read board type and hw id from gpio pins on the enbw_cmc board, and use board type for setting up different gpio pin settings. - do not pass "davinci_mmc.use_dma=0" to linux, as MMC now works with DMA. - update logbuf support: store post word in RTC scratch register - add support for configuring KSZ8864RMN switch through a config file on u-boot startup. For more infos see: doc/README.switch_config Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Sandeep Paulraj <s-paulraj@ti.com>
2012-07-07omap4/5: Use CPUDIR for .lds scriptThomas Weber
Signed-off-by: Thomas Weber <thomas@tomweber.eu>
2012-07-07tegra: trimslice: fix a couple typosStephen Warren
Fix the .dts file USB unit addresses not to duplicate each-other. Fix the board name string to indicate the vendor is Compulab not NVIDIA. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07arm: Tegra: Use ODMDATA from BCT in IRAMTom Warren
Walk the BIT and BCT to find the ODMDATA word in the CustomerData field and put it into Scratch20 reg for use by kernel, etc. Built all Tegra builds OK; Booted on Seaboard and saw ODMDATA in PMC scratch20 was the same as the value in my burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities will have to specify the odmdata (nvflash --odmdata n) on the command line or via a cfg file, or built in to their BCT. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2012-07-07tegra: seaboard: disable SPI, move environment to eMMCStephen Warren
The SPI hardware on Seaboard is too broken to use; it is muxed with the console UART and requires evil interactions between the SPI and UART drivers to work even partially. The current code in U-Boot is not sufficient to make this work correctly; auto boot is aborted due to corruption in the UART RX channel interrupting it. Instead, move the environment to eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage, irrespective of whether the board boots from SPI, NAND, or eMMC: if U-Boot is stored in eMMC, it will be stored well below this location. The kernel only uses the general area of the eMMC once booted, not the boot sectors. Boards that are derivatives of Seaboard don't have the muxing issue, and should/could have a separate U-Boot configuration file that does enable SPI if desired. Alternatively, the environment could be stored in NAND flash, but we currently have no driver for that controller. Signed-off-by: Stephen Warren <swarren@nvidia.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: paz00: store environment in eMMCStephen Warren
Store the environment in eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage: U-Boot is stored well below this location, and the kernel only uses the general area of the eMMC once booted, not the boot sectors. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07tegra: trimslice: store environment in SPI flashStephen Warren
The chosen flash offset matches Compulab's downstream U-Boot. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07gpio: tegra2: rename tegra2_gpio.* to tegra_gpio.*Tom Warren
In anticipation of Tegra3 support, continue removing/renaming Tegra2-specific files. No functional changes (yet). Updated copyrights to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07mmc: tegra2: rename tegra2_mmc.* to tegra_mmc.*Tom Warren
In anticipation of Tegra3 support, continue removing/renaming Tegra2-specific files. No functional changes (yet). Updated copyrights to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07spi: tegra2: rename tegra2_spi.* to tegra_spi.*Tom Warren
In anticipation of Tegra3 support, start removing/renaming Tegra2-specific files. No functional changes (yet). Also updated copyright to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
generated by cgit (git 2.34.1) at 2024-12-28 07:29:27 +0000