| Age | Commit message (Collapse) | Author |
|---|
|
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
The symbol CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID was recently dropped
from usage and CONFIG_OMAP3_MICRON_DDR is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move this entry to Kconfig. As it is a hardware watchdog, select
HW_WATCHDOG. While we could default to enabling this for all platforms,
it is currently only enabled by default on AM33XX, so keep that logic
today.
Cc: Roger Meier <r.meier@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot. select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This driver is used often enough such that we want to have this enabled
by default on any ARCH_OMAP2PLUS board, and this only compiles on
ARCH_OMAP2PLUS due to required defines, so mark that as the depends.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We no longer have a need for a per-board CONFIG_OMAP3_xxx define (we
have CONFIG_TARGET_xxx when this is required), so drop these unused
references.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
While there are a few different OMAP4 SoCs, today we always set
CONFIG_OMAP4430 and CONFIG_OMAP44XX. Convert the few test of
CONFIG_OMAP4430 to CONFIG_OMAP44XX.
Cc: Marek Vasut <marex@denx.de>
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We make use of CONFIG_OMAP3_EVM today to know when to do a specific
tweak in MUSB. This can be tested on via CONFIG_TARGET_OMAP3_EVM
instead, so switch there so we can drop the now unused symbol
CONFIG_OMAP3_EVM. In investigating what to do about the symbol usage we
see that the cairo board defines the same function, but never called it
(as it does not define CONFIG_OMAP3_EVM) and was just returning anyhow,
so drop that function from that board.
Cc: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead. With that
changed we can drop all defines of CONFIG_OMAP. While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
This particular macro hasn't been used in the code for some time, remove
these references that were missed.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The default value of CONFIG_SYS_BOOTM_LEN is too small for typical
boston Linux kernels. Increase the limit to 64MB, which covers current
kernels with plenty of breathing room.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable SPL_DM on all AM335x based TI platforms.
http://patchwork.ozlabs.org/patch/751300/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
No reason to use a separate load script for am33xx than using
omap-common load script.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
|
|
|
|
To include the ability to load from an SPI flash in SPL, it's not
sufficient to define SPL_SPI_SUPPORT and SPL_SPI_FLASH_SUPPORT via
Kconfig... so we conditionally define SPL_SPI_LOAD if SPI support
is already enabled for SPL via Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This serves as an example for bcm6358-leds.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
CFE checks CPU Thread in a different way (using register $22):
mfc0 t1, C0_BCM_CONFIG, 3 # $22
li t2, CP0_CMT_TPID # (1 << 31)
and t1, t2
bnez t1, 2f # if we are running on thread 1, skip init
nop
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With the addition of Kconfig now having CONFIG_TWL4030_POWER and
with that being the default when OMAP34XX is selected, this
is no longer needed in include/configs and can be removed from the
whitelist.
This has only been tested on logic PD DM3730 using ti_omap3_common.h
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
|
|
Adjust the video driver to work with driver model and move over existing
baords. There is no need to keep the old code.
We can also drop setting of CONFIG_FB_ADDR since driver model doesn't have
this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Start using driver model for USB on the Raspberry Pi. The dwc2 supports
this now so this is just a config change.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This is not needed now that serial uses driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Enable CONFIG_DM_ETH to make MACB to support driver model.
Because the USB Ether doesn't support driver model so far,
remove this feature.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Move existing configuration from header file to defconfig or dts as
appropriate.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add NAND configuration parameters to A8K shared config file.
Add defconfig for db-88f7040 board with boot from NAND setup.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
|
|
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
netboot allows to boot an external image using TFTP and NFS protocols
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
