summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2016-02-26powerpc/t208xqds: fix esdhc peripheral clock supportYangbo Lu
The patch that enabled eSDHC peripheral clock support had an obvious error as below. This patch is used to fix it. +#define define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK Fixes: 3285e6cbcc1b ("powerpc/t2080qds: enable eSDHC peripheral clock support") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-26ARM: rpi: increase CONFIG_SYS_MAXARGSStephen Warren
This allows all the hush tests implemented in test/py to pass, under qemu at least. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-25ARM: zynq: zynqmp: Enable DCC serial driver by defaultMichal Simek
Compile DCC serial driver by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-24Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2016-02-24Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2016-02-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-02-24rpi: always scroll by 10 linesLubomir Rintel
Scrolling the simple framebuffer is really slow in Raspberry Pi to the point it delays the boot by a second or two and makes longer output inconvenient to follow (printenv, md). Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2016-02-24arm: am437x: cm-t43: bring back BOOTDELAY featureNikita Kiryanov
Commit 755324 (configs: Use config_distro_defaults.h in ti_armv7_common.h) made ti_armv7_common.h include config_distro_defaults.h. This breaks the bootdelay feature in cm_t43 because now the - #include ti_armv7_common.h (#define CONFIG_BOOTDELAY 1) - #undef CONFIG_BOOTDELAY - #include config_distro_defaults.h (#define CONFIG_BOOTDELAY 2) dance in cm_t43.h is no longer valid and in fact leads to CONFIG_BOOTDELAY not being defined. Adapt the config file to the new inclusion hierarchy. Cc: Tom Rini <trini@konsulko.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24arm: am437x: cm-t43: update parameters for raw mmc bootNikita Kiryanov
Update U-Boot offset and size for raw mmc boot. Cc: Tom Rini <trini@konsulko.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24arm: am437x: cm-t43: set MPU and CORE voltages on bootNikita Kiryanov
During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators are not updated. This is not a problem in cold boot since the default values that the pmic outputs are correct, but if Linux were to switch the module to a low power OPP, the new voltage values will be retained after a reboot and the module will likely hang once U-Boot raises the CPU frequency back up. Set both CORE and MPU regulators to to 1.1V on boot. Cc: Tom Rini <trini@konsulko.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24arm: am437x: cm-t43: support all available SPI flash chipsNikita Kiryanov
Add full support for SPI flash chips to future-proof U-Boot for cm-t43. Cc: Tom Rini <trini@konsulko.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24arm: am437x: cm-t43: migrate CONFIG_DM_SERIAL to config fileNikita Kiryanov
Move CONFIG_DM_SERIAL to cm_t43_defconfig. This forces us to update the CONFIG_SYS_NS16550_REG_SIZE value for SPL. Cc: Tom Rini <trini@konsulko.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24arm: am437x: cm-t43: fix cm-t43 bootNikita Kiryanov
spl_board_init() is necessary for boot. Remove the #undef that keeps it out of the boot sequence. Cc: Tom Rini <trini@konsulko.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24board/BuR/kwb: cosmetic changesHannes Schmelzer
- fixup typo - fixup identation Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24board/BuR: split bur_am335x_common.h into am335x-specific and BuR common partsHannes Schmelzer
bur_am335x_common.h today holds all common configuration which is shared over all B&R boards. In future we want to bring up boards which are not based on AM335x only but we still want to have common configuration over all B&R boards independent from their architecture. To prepare this we introduce a new file "bur_cfg_common.h", where we move all common things, which are not architecture specific, from bur_am335x_common.h. On B&R am335x boards we include from now: #include <configs/bur_cfg_common.h> #include <configs/bur_am335x_common.h> On other B&R boards, we include only #include <configs/bur_cfg_common.h> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24board/BuR: move everything possible from board's headerfile to KConfigHannes Schmelzer
We drop everything possible things from board headerfiles and replace this functionality with responsible settings in Kconfig (_defconfig). Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24board/BuR: drop ETH-support in SPL-StageHannes Schmelzer
During very early prototype-phase we did boot the AM335x boards initially from CPSW-EMAC. Now we don't need this feature anymore. So we drop it to save MLO-space and having therefore a more quickly boot. Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-24OMAP3SOM BOARD: Auto detect Logic PD ModelsAdam Ford
Logic PD makes four different system on modules. This patch will auto detect the board type and identify the corresponding device tree image. V2: Added 'default:' case to switch statement Since board_late_init() is defined as int, we now return 0 Signed-off-by: Derald Woods <woods.technical@gmail.com> Signed-off-by: Adam Ford <aford173@gmail.com>
2016-02-24stm32: add support for stm32f7 & stm32f746 discovery boardVikas Manocha
This patch adds support for stm32f7 family & stm32f746 board. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2016-02-24arm: socfpga: Add missing CONFIG_BUILD_TARGETMarek Vasut
Add the missing CONFIG_BUILD_TARGET to get u-boot-with-spl.sfp built automatically upon running make in the source tree. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Chin Liang See <clsee@altera.com> Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
2016-02-24implement Fastboot via USB OTG on bcm28155_ap boardsSteve Rae
Don't understand how it happened, but this change got applied twice! Therefore, removing the duplicated items. Signed-off-by: Steve Rae <srae@broadcom.com>
2016-02-24dfu: odroid xu3: Define DFU_MANIFEST_POLL_TIMEOUT to handle large files ↵Lukasz Majewski
transmission and storage As tested on the Odroid XU3, large files to be stored on the file system require considerable time to be physically written to the medium. The default 300 ms is not enough to store large file (e.g. 26 MiB). To fix this situation the DFU_MANIFEST_POLL_TIMEOUT has been defined. It is used to cease the communication with dfu-util and allow the target board to store the data on file system. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2016-02-24board: ls1043ardb: Add micro QE support for ls1043ardbZhao Qiang
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24armv8/ls1043aqds: Add USB support for ls1043aqdsQianyu Gong
Add USB XHCI support for ls1043qds board. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24armv8: ls2080: Update bootcmd env variablePrabhakar Kushwaha
Before Linux boot DPL must be deployed to DPAA2 interface. So update bootcmd env variable to make sure DPL deployment before Linux boot. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24armv8: ls2080: Add mcinitcmd env variable in default envPrabhakar Kushwaha
Define mcinitcmd env variable to load Management complex during u-boot boot sequence. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24arm: ls1021a: Add QSPI or IFC support in SD boot for LS1021AQDS boardAlison Wang
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in SD boot now. For the customer's demand, QSPI needs to be supported in SD boot too. This patch adds QSPI or IFC support in SD boot according to the corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig is used to support QSPI in SD boot. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24armv8: ls2080a: Increase default hugepage countAshish Kumar
Increase default hugepage count to 256 from 16 Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-23Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-02-23sunxi: H3: Add support for the host usb-physJelle van der Waa
Add support for phy 1-3. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> [hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-02-23sunxi: power: add support for sy8106a driverJelle van der Waa
SY8106A is a PMIC which is used on the Allwinner H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is implemented to set the default V-CPU voltage to 1200 mV. This driver is required to ensure the SY8106A V-CPU voltage is set to 1200 mV after a software reset. On cold boot the default SY8106A output voltage is selected to be 1200 mV by a pair of resistors on the Orange Pi PC and Plus. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-02-23arm: ls1021aqds: Convert to driver model and enable serial supportYork Sun
Split duart configuration as device tree file. Move /chosen node out of board commone device tree. Convert ls1021aqds nor and SD configurations to driver model support (qspi already uses DM). Enable ns16550 DM serial driver for nor configurations. Signed-off-by: York Sun <york.sun@nxp.com> CC: Alison Wang <alison.wang@nxp.com> CC: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-23Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2016-02-23ARM: zynq: Wire-up saving environment to QSPIMichal Simek
Extend options for saving variables to QSPI. Reviewed-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Michal Simek <monstr@monstr.eu>
2016-02-22ARM: zynq: Enable EDID for zyboMichal Simek
Zybo contains on board HDMI that's why enable EDID. Doing it via config because zynq i2c driver hasn't been moved to DM yet and enabling via Kconfig requires DM_I2C. This will be moved that driver is moved to DM. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22ARM: zynq: Enable Realtek phys by defaultMichal Simek
This phy is available at Zybo board. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22zynq-common: Fix usbboot env variableJason Wu
Remove the miss-placed \0 and add missing ; for usbboot env variable. Signed-off-by: Jason Wu <jason.wu.misc@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22ARM: zynq: Enable SPL RAM support by defaultMichal Simek
Use RAM support in jtagboot mode. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
2016-02-22ARM: zynq: Remove ZYNQ_BOOT_FREEBSD optionMichal Simek
Remove CONFIG_ZYNQ_BOOT_FREEBSD configuration option and setup CONFIG_SYS_MMC_MAX_DEVICE 1 for all Zynq boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22ARM: zynq: Read memory size setting from DTMichal Simek
OF_CONTROL is setup by default and memory reading is done via DT. Remove all config files with memory references. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22mmc: Kconfig: Add Arasan SDHCI entryMichal Simek
Add Arasan SDHCI entry to Kconfig and fix all references. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22zynq: zc770: Remove unused ifdefs for xm011 and xm013Michal Simek
Clean config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-21Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-02-21imx: mx7dsabresd: add command and macros for boot m4 corePeng Fan
Introduce macros and command to support booting M4 core for i.MX7D SabreSD board. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6sxsabresd: add command and macros for boot m4 corePeng Fan
Introduce macros and command to support booting M4 core for i.MX6SX SabreSD board. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21board: tbs2910: Autoselect environment device when booting from SDSoeren Moch
Implement board specific functions to select the environment device and partition when booting from SD/MMC. SD2: mmc 0 0 SD3: mmc 1 0 eMMC: mmc 2 1 Signed-off-by: Soeren Moch <smoch@web.de>
2016-02-21mx6ul_14x14_evk: Select CONFIG_FSL_QSPIFabio Estevam
Select CONFIG_FSL_QSPI so that the SPI can be probed: => sf probe SF: Detected N25Q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-02-21x86: Add Intel Cougar Canyon 2 boardBin Meng
This adds basic support to Intel Cougar Canyon 2 board, a board based on Chief River platform with an Ivy Bridge processor and a Panther Point chipset. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-02-20Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-02-19ARM: Add Support for the VInCo platformGregory CLEMENT
The Versatile Industrial Communication platform is a community oriented board from Landis + Gyr. It comes with: - an RS-485 port - 2 Ethernet ports - a wireless M-BUS - a 4G modem - a 4MB SPI flash - a 4GB eMMC Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> [rebase on current TOT] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
generated by cgit (git 2.34.1) at 2024-12-27 02:18:20 +0000