summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2012-09-21Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD
2012-09-17mx28evk: extend default environmentOtavio Salvador
The environment has been based on mx53loco and m28evk but keeping the possibility to easy change the default console device as Freescale and mainline kernels differ on the device name. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-10Tegra: Change Tegra20 to Tegra in common code, prep for T30Tom Warren
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate. Convert tegra20_ source file and function names to tegra_, also. Upcoming Tegra30 port will use common code/defines/names where possible. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2012-09-10MX35: mx35pdk: add support for MMCStefano Babic
Add support for SD card and change the default environment due to increased u-boot size. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-09-10ima3-mx53:Rename CONFIG_PRIME => CONFIG_ETHPRME, removeAshok Kumar Reddy
unused macro CONFIG_DISCOVER_PHY Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-07tegra: put eMMC environment into the boot sectorsStephen Warren
When I set up Tegra's config files to put the environment into eMMC, I assumed that CONFIG_ENV_OFFSET was a linearized address relative to the start of the eMMC device, and spanning HW partitions boot0, boot1, general* and the user area in order. However, it turns out that the offset is actually relative to the beginning of the user area. Hence, the environment block ended up in a different location to expected and documented. Set CONFIG_SYS_MMC_ENV_PART=2 (boot1) to solve this, and adjust CONFIG_ENV_OFFSET to be relative to the start of boot1, not the entire eMMC. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07tegra: Enable NAND on TECThierry Reding
This commit enables NAND support on the Tamonten Evaluation Carrier and adds the corresponding device tree nodes. Furthermore, the U-Boot environment can now be stored in NAND. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07tegra: enable NAND on HarmonyStephen Warren
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07tegra: Enable NAND on SeaboardSimon Glass
This enables NAND support for the Seaboard. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-06mx31: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX31 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Helmut Raiger <helmut.raiger@hale.at>
2012-09-06mx35: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX35 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-06mx25: Define default SoC input clock frequenciesBenoît Thébaudeau
Define default SoC input clock frequencies for i.MX25 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Matthias Weisser <weisserm@arcor.de>
2012-09-05Merge remote-tracking branch 'u-boot-ti/master' into mAlbert ARIBAUD
2012-09-04OMAP3: mt_ventoux: added video supportStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-09-04OMAP3: mt_ventoux: activate GPIO4Stefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-09-04OMAP3: tam3517: add function to read MAC from EEPROMStefano Babic
The manufacturer delivers the TAM3517 SOM with 4 MAC address. They are stored on the EEPROM of the SOM. The patch adds a function to get their values and set the ethaddr variables. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-09-04Merge remote-tracking branch 'u-boot-atmel/master' into mAlbert ARIBAUD
2012-09-04Fixes the crippled console output on PortuxG20.Markus Hubig
In order to use the serial interface on the PortuxG20 we need to enable the level converter first by setting the PC9 pin to high. The level converter needs some time to settle so we have to use the mdelay() function to wait for some time. Unfortunately we have no timers available at board_early_init_f() so we enable the serial output early within board_postclk_init(). Now the U-Boot output looks fine: | U-Boot 2012.07-00132-gaf1a3b0-dirty (Aug 16 2012 - 18:21:32) | | CPU: AT91SAM9G20 | Crystal frequency: 18.432 MHz | CPU clock : 396.288 MHz | Master clock : 132.096 MHz | DRAM: 64 MiB | WARNING: Caches not enabled | NAND: 128 MiB | In: serial | Out: serial | Err: serial | Net: macb0 | Hit any key to stop autoboot: 0 Signed-off-by: Markus Hubig <mhubig@imko.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-04atmel: eb_cpux9k2: add ram target configurationJens Scharsig
* add ram target for EB+CPUx9k2 board (eb_cpux9k2_ram_config) Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de> Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-04integrator: break out common configLinus Walleij
The configuration that is common for all Integrator boards may just as well be stored in a common include file as per pattern from other boards. This eases maintenance quite a bit. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-04SCSPS1: Enable cachesMarek Vasut
Enable caches, make it faster! Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2012-09-04mx28evk: Add USB Ethernet supportFabio Estevam
Add USB Ethernet support. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Marek Vasut <marex@denx.de>
2012-09-04M28: Fix the use of gpmi-nand in mtdpartsMarek Vasut
The mtd name of the NAND in Linux is "gpmi-nand", not "gpmi-nand.0" as it would be expected, since the controller doesn't support multiple NANDs attached to it as of now. Rectify this flub by adjusting default mtdparts. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-04MX28: mx28evk: Enable SPI DMAOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-03arm/km: remove unused codeHolger Brunck
For some reasons we had an own implementaion of dram_init and dram_init_banksize. This is not needed anymore, use the standard kirkwood functions instead. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-09-03arm/km: fix frequency of the SPI NOR FlashValentin Longchamp
According to our last HW measures, this could be raised while still compatible with the potential delays on the lines. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-09-03km/arm: set SPI NOR Flash default parametersValentin Longchamp
These parameters are used by the the sf probe command that are used by our update script and they therefore need to be set for all of our boards. The timing is the same as for the ENV SPI NOR Flash (since it's the same physical device) and takes the boco2 delay on the bus into account. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
2012-09-03edminiv2: orion5x: fix GPIO inits and valuesAlbert ARIBAUD
Orion5x did not actually write GPIO output values or input polarities, and ED Mini V2 had bad or missing values for GPIO settings. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-09-01at91: 9x5: Enable PMECC for 5series ek board.Wu, Josh
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01atmel: at91sam9x5: add spi flash boot supportBo Shen
Add at91sam9x5 series spi flash boot support Using at91sam9x5ek_spiflash to configure, then it can boot from at25df321 serial flash SPI mater work in 30Mhz speed, while not 1Mhz speed. This will base on atmel_spi patch, or else, it will occur receive overrun Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01arm: sam9g10/sam9m10g45: remove CONFIG_ARCH_CPU_INITBo Shen
Remove CONFIG_ARCH_CPU_INIT for at91sam9g10ek and at91sam9m10g45ek Signed-off-by: Bo Shen <voice.shen@atmel.com> [rebase on TOT] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01at91sam9263ek: fix 'update' scriptAndreas Bießmann
The old update script uses 'load_addr' which is never set. Use 'fileaddr' instead which is automagically set by e.g. dhcp. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Stelian Pop <stelian@popies.net>
2012-09-01ARM : at91sam9x5 : Remove CONFIG_ARCH_CPU_INITBo Shen
Remove CONFIG_ARCH_CPU_INIT, no need it anymore Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01efikamx: move and rename Efika MX directories and config files to prepare ↵Matt Sealey
for new boards * Move Efika MX Smarttop and Smartbook boards into a "genesi" vendor directory * Rename efikamx -> mx51_efikamx since there is an mx53_efikamx and mx6_efikamx to come Signed-off-by: Matt Sealey <matt@genesi-usa.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01MX28: m28evk: Enable SPI DMAMarek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2012-09-01MX28: m28evk: Align SSP clock speedMarek Vasut
Align the SSP clock speed with oscilator to achieve higher transfer stability. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2012-09-01imx27lite: update with gpio api change (v4)trem
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01MX: Set a common gpio.h for all i.MXStefano Babic
Each i.MX has its own gpio.h, defining the same structure. The internal GPIO controller has the same layout (at least for the register used by u-boot) and can be shared. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Matt Sealey <matt@genesi-usa.com>
2012-09-01mx28evk: Remove unneeded 'undef'Fabio Estevam
There is no need to undef an option that is not enabled by default. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01MX28: Move "regs-base.h" include after SoC type configurationOtavio Salvador
For i.MX233 addition the base registers need to be change so the SoC definition needs to be known before the header include. The following boards has been changed: * apx4devkit * m28evk * mx28evk * sc_sps_1 Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01mx53evk: add boot_mode supportTroy Kisky
This allows a watchdog reset to start the ROM's usb/serial downloader, or boot from an sdcard. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-09-01mx6qsabrelite: add boot_mode supportTroy Kisky
This allows a watchdog reset to start the ROM's usb downloader, or boot from an sdcard. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-09-01apx4devkit: Turn on cachesFabio Estevam
Turn on data and instruction caches. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> include/configs/apx4devkit.h | 2 -- 1 files changed, 0 insertions(+), 2 deletions(-) Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
2012-09-01m28evk: Turn on cachesFabio Estevam
Turn on data and instruction caches. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-09-01arm:cache:trats: Enable PL310 L2 Cache Controller at TRATS Samsung boardŁukasz Majewski
Enable the PL310 L2 cache controller at TRATS Samsung board. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-09-01arm:trats: loaduimage environment variable defied for TRATS targetŁukasz Majewski
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-09-01SMDK5250: Enable UART and MMC for Exynos5250 Rev 1.0Rajeshwari Shinde
This patch sets UART3 and MMC channle 0 for Exynos5250 Rev 1.0 Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-09-01SMDK5250: Add smdk5250-uboot-spl.ldsRajeshwari Shinde
Default spl/u-boot-spl.lds created by spl/Makefile resolves the spl text load addr to 0x0. As 0x0 belongs to iROM addr so Global variables can not be used. Adding specific smdk5250-uboot-spl.lds makes possible to use Global Variables in spl. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-09-01ARM: Remove unused stack and irq config definesRob Herring
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-09-01tegra20: enable SPL for tegra20 boardsAllen Martin
Add SPL options to tegra20 config files and enable SPL build for tegra20 boards. Also remove redundant code from u-boot that is not contained in SPL. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
generated by cgit (git 2.34.1) at 2024-12-26 00:31:35 +0000