summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2010-06-23Get rid of bogus CONFIG_SYS_BUS_HZ and CONFIG_SYS_CONFIG_BUS_CLK definitionsWolfgang Denk
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Frank Gottschling <fgottschling@eltec.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Eran Man <eran@nbase.co.il> Cc: Stefan Roese <sr@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
2010-06-22DaVinci: EMAC: Get EMAC_MDIO_PHY_NUM from config filesPrakash PM
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h. Because of this, EMAC does not work on EVMs which do not have phy connected at 1. Moving the macro to board config file makes this configurable depending on where the phy is connected on the MDIO bus. This patch fixes the board reset issue observed during network access on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1 but it is 0 on DM365EVM. This patch is verified on da830/omap-l137, dm365 and dm644x evms. Signed-off-by: Prakash PM <prakash.pm@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-18Merge branch 'master' into nextWolfgang Denk
Conflicts: Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-06-17ppc4xx: icon: add support for SM502 chipAnatolij Gustschin
Adds initialization code for SM502 graphics controller and NL6448BC20-21D LCD panel. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
2010-06-17Merge branch 'master' of git://git.denx.de/u-boot-marvellWolfgang Denk
2010-06-17Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk
Conflicts: CONFLICT (rename/add): Rename board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile in 89b765c7f6ddfde07ba673dd4adbeb5da391a81b. board/ti/tnetv107xevm/Makefile added in HEAD But files were identical, so no problem. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-06-17Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-06-17Add support for the LaCie ED Mini V2 boardAlbert Aribaud
This patch adds support for the LaCie ED Mini V2 product which is based on the Marvell Orion5x SoC. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-06-14s5pc1xx: Add support for Samsung Goni boardMinkyu Kang
This patch adds support for the Samsung Goni board (S5PC110 SoC) Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-06-10TI: DaVinci: Add board specific code for da850 EVMSudhakar Rajashekhara
Provides initial support for TI OMAP-L138/DA850 SoC devices on a Logic PD EVM board. Provides: Initial boot and configuration. Support for i2c. UART support (console). Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Acked-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08AM35x: Add support for EMIF4Vaibhav Hiremath
This patch adds support for the EMIF4 interface available in the AM35x processors. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08AM35x: Add support for AM3517EVMVaibhav Hiremath
This patch adds basic support for the AM3517EVM. It includes: - Board files (.c and .h) - Default configuration file - Updates for Makefile Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08omap3: Consolidate SDRC related operationsVaibhav Hiremath
Consolidated SDRC related functions into one file - sdrc.c And also replaced sdrc_init with generic memory init function (mem_init), this generalization of omap memory setup is necessary to support the new emif4 interface introduced in AM3517. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08OMAP3EVM: Added NAND supportVaibhav Hiremath
The EVMS have been shipping with NAND (instead of OneNAND) as default. So, this patch sets NAND as default. To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the config file omap3_evm.h. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08TI: TNETV107X EVM initial supportCyril Chemparathy
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a bunch on on-chip integrated peripherals. This patch adds support for the TNETV107X EVM board. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08ARM1176: Coexist with other ARM1176 platformsCyril Chemparathy
The current ARM1176 CPU specific code is too specific to the SMDK6400 architecture. The following changes were necessary prerequisites for the addition of other SoCs based on ARM1176. Existing board's (SMDK6400) configuration has been modified to keep behavior unchanged despite these changes. 1. Peripheral port remap configurability The earlier code had hardcoded remap values specific to s3c64xx in start.S. This change makes the peripheral port remap addresses and sizes configurable. 2. U-Boot code relocation support Most architectures allow u-boot code to run initially at a different address (possibly in NOR) and then get relocated to its final resting place in RAM. Added support for this capability in ARM1176 architecture. 3. Disable TCM if necessary If a ROM based bootloader happened to have initialized TCM, we disable it here to keep things sane. 4. Remove unnecessary SoC specific includes ARM1176 code does not really need this SoC specific include. The presence of this include prevents builds on other ARM1176 archs. 5. Modified virt-to-phys conversion during MMU disable The original MMU disable code masks out too many bits from the load address when it tries to figure out the physical address of the jump target label. Consequently, it ends up branching to the wrong address after disabling the MMU. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07AM35x: Add support for EMIF4Vaibhav Hiremath
This patch adds support for the EMIF4 interface available in the AM35x processors. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07AM35x: Add support for AM3517EVMVaibhav Hiremath
This patch adds basic support for the AM3517EVM. It includes: - Board files (.c and .h) - Default configuration file - Updates for Makefile Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07omap3: Consolidate SDRC related operationsVaibhav Hiremath
Consolidated SDRC related functions into one file - sdrc.c And also replaced sdrc_init with generic memory init function (mem_init), this generalization of omap memory setup is necessary to support the new emif4 interface introduced in AM3517. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07OMAP3EVM: Added NAND supportVaibhav Hiremath
The EVMS have been shipping with NAND (instead of OneNAND) as default. So, this patch sets NAND as default. To choose OneNAND, define CMD_ONENAND instead of CMD_NAND in the config file omap3_evm.h. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07TI: TNETV107X EVM initial supportCyril Chemparathy
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a bunch on on-chip integrated peripherals. This patch adds support for the TNETV107X EVM board. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07ARM1176: Coexist with other ARM1176 platformsCyril Chemparathy
The current ARM1176 CPU specific code is too specific to the SMDK6400 architecture. The following changes were necessary prerequisites for the addition of other SoCs based on ARM1176. Existing board's (SMDK6400) configuration has been modified to keep behavior unchanged despite these changes. 1. Peripheral port remap configurability The earlier code had hardcoded remap values specific to s3c64xx in start.S. This change makes the peripheral port remap addresses and sizes configurable. 2. U-Boot code relocation support Most architectures allow u-boot code to run initially at a different address (possibly in NOR) and then get relocated to its final resting place in RAM. Added support for this capability in ARM1176 architecture. 3. Disable TCM if necessary If a ROM based bootloader happened to have initialized TCM, we disable it here to keep things sane. 4. Remove unnecessary SoC specific includes ARM1176 code does not really need this SoC specific include. The presence of this include prevents builds on other ARM1176 archs. 5. Modified virt-to-phys conversion during MMU disable The original MMU disable code masks out too many bits from the load address when it tries to figure out the physical address of the jump target label. Consequently, it ends up branching to the wrong address after disabling the MMU. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-06add new board pm9g45Asen Dimov
Add the new board PM9G45 from Ronetix GmbH. * AT91SAM9G45 MCU at 400Mhz. * 128MB DDR2 SDRAM * 256MB NAND * 10/100 MBits Ethernet DP83848 * Serial number chip DS2401 The board is made as SODIMM200 module. For more info www.ronatix.at or info@ronetix.at. Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-06-04Update SICRL_USBDR to reflect 4 different settingsRon Madrid
This patch changed the SICRL_USBDR define to reflect the 4 different bit settings for this two-bit field. The four different options are '00', '01', '10', and '11'. This patch also corrects the config file for SIMPC8313 and MPC8313ERDB for the appropriate fields. This change only affects the MPC8313 cpu. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-05-28nios: remove nios-32 archThomas Chou
The nios-32 arch is obsolete and broken. So it is removed. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-28nios2: add gpio support to nios2-generic boardThomas Chou
This patch adds gpio support of Altera PIO component to the nios2-generic board. Though it drives only gpio_led at the moment, it supports bidirectional port to control bit-banging I2C, NAND flash busy status or button switches, etc. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Tested-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-05-21Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk
2010-05-19MX31: Added support for the Casio COM57H5M10XRC to QONGStefano Babic
The patch adds setup to connect a CASIO COM57H5M10XRC (640x480 TFT display) to the QONG module. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-17Fix SICRL setting in SIMPC8313Ron Madrid
This patch sets the SICRL_LBC bits in SICRL to change the function of the associated pins to GPIO functionality. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
2010-05-07mpc83xx/mvBLM7: add usb commands and cleanup.Andre Schwarz
Add USB commands. Rename autoscript to bootscript. Add automatic bootscript image generation to makefile. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-05-07mpc83xx: Add UPMA configuration to SIMPC8313Ron Madrid
Added UPM array table, upmconfig, and Local Bus configuration support for SIMPC8313 Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-05-0674xx_7xx: CPCI750: Add ECC support on esd CPCI-CPU/750 boardReinhard Arlt
Add ECC support for DDR RAM for MV64360 on esd CPCI-CPU/750 board. This patch also adds the "pldver" command to display the CPLD revision. Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2010-05-06eNET: Implement eNET WatchdogGraeme Russ
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06eNET: Use SC520 MMCR to reset eNET boardGraeme Russ
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06eNET: Add support for onboard RTL8100B (RTL8139) chipsGraeme Russ
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06eNET: Fix CONFIG_SYS_HZ to be 1000Graeme Russ
The clock interupt has always been 1kHz as per timer_init() in /arch/i386/cpu/sc520/sc520_timer.c Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06eNET: Fix Flash WriteGraeme Russ
Onboard AMD Flash chip does not support buffered writes Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06x86: Use CONFIG_SERIAL_MULTIGraeme Russ
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-05Add SPI support to mx51evk boardStefano Babic
The patch adds SPI devices to the mx51evk board. The MC13892 chip (PMIC) is supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05MX31: Add support for PMIC to the QONG moduleStefano Babic
Add support for the PMIC (MC13783) controller and enables charging of the RTC battery. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05MX: RTC13783 uses general function to access PMICStefano Babic
The RTC is part of the Freescale's PMIC controller. Use general function to access to PMIC internal registers. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05i.MX31: Activate NAND support for i.MX31 Litekit board.Magnus Lilja
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-04configs: remove unused CONFIG_COMMAND_HISTORYKim Phillips
$ git grep CONFIG_COMMAND_HISTORY CHANGELOG: CONFIG_COMMAND_HISTORY include/configs/AP1000.h:#define CONFIG_COMMAND_HISTORY 1 include/configs/keymile-common.h:#define CONFIG_COMMAND_HISTORY 1 include/configs/manroland/common.h:#define CONFIG_COMMAND_HISTORY 1 $ Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
2010-05-04Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-05-01Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/masterWolfgang Denk
2010-04-30pm9263 converted to at91 soc accessAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-04-30MX31: Add UBI support to QONG moduleStefano Babic
The UBI/UBIFS support is added to the QONG module. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX31: Add support for NAND to QONG boardStefano Babic
The NAND device is connected to the FPGA of the QONG board and not to the NFC controller. For this reason, the FPGA must be set and initialized before accessing to the NAND itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30configs/openrd_base.h: reordered macrosFrans Meulenbroeks
moved CONFIG_CMD_FAT to filesystem section swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-04-30configs/sheevaplug: added a few additional commandsFrans Meulenbroeks
This patch includes a few additional commands in the sheevaplug version of u-boot: - support for LONGHELP so you can get help messages - auto completion and command editing - ubi and mii support - ext2 filesystem (convenient if you have an ext2 from which you want to boot) - jffs2 and ubifs filesystems (if you want to use these in NAND) This also makes it more similar to openrd client. Side effect of this patch is that the code now needs 3 sectors i.s.o. 2 so an existing env is overwritten Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-15 22:52:53 +0000