summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2015-10-22ARM: k2g: Add clock informationVitaly Andrianov
Add clock information for Galileo Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22ARM: dts: k2hk: Enable OF_CONTROL and DMLokesh Vutla
Import k2hk specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: keystone2: spl: Fix stack allocation with CONFIG_SYS_MALLOC_F_LENLokesh Vutla
If CONFIG_SYS_MALLOC_F_LEN is enabled, the stack is moved down to the specified size to make the malloc function available before relocation. But on keystone platforms SYS_SPL_MALLOC is immediately preceding stack, which is causing an overlap with this config enabled. So leave a gap between malloc space and stack space. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ti_omap5_common.h: Switch to CONFIG_OMAP_SERIAL for non-SPL DM_SERIALTom Rini
Tested on J6Eco EVM Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-22ti_omap4_common.h: Switch to CONFIG_OMAP_SERIAL for non-SPL DM_SERIALTom Rini
Tested on Pandaboard Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-22am335x_evm: do not define usb ether gadget when Eth DM is definedMugunthan V N
Since usb ether gadget doesn't have support for driver model, so not defining usb ether gadget when ethernet driver model is defined. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22configs: am335x_evm: Support distro bootcmdsSjoerd Simons
Add support for distro bootcmds and network booting while retaining backwards compatibility with the current "legacy" setup. With these changes the default boot sequence becomes: * SD card (standard distro boot) * SD card (legacy boot) * EMMC (standard distro boot) * EMMC (legacy boot) * Nand (legacy boot) * PXE (standard distro boot) * DHCP (standard distro boot) The older boot scripts have some overlap with what the distro bootcommands to however i've left them unchanged to prevent introduction of subtle bugs. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2015-10-22configs: ti_armv7_common.h: Add default addresses for pxe and scriptsSjoerd Simons
Add mandatory address variables for loading scripts and pxe configuration as per README.distro Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2015-10-21Merge git://git.denx.de/u-boot-x86Tom Rini
2015-10-21x86: Add support for Advantech SOM-6896George McCollister
Advantech SOM-6896 is a Broadwell U based COM Express Compact Module Type 6. This patch adds support for it as a coreboot payload. On board SATA and SPI are functional. On board Ethernet isn't functional but since it's optional and ties up a PCIe x4 that is otherwise brought out, this isn't a concern at the moment. USB doesn't work since the xHCI driver appears to be broken. Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-21cmd: Convert CONFIG_CMD_ELF to KconfigBin Meng
Convert CONFIG_CMD_ELF to Kconfig and tidy up affected boards. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-10-21x86: Remove quotation mark in CONFIG_HOSTNAMEBin Meng
CONFIG_HOSTNAME is an environment varible, so that quotation mark is not needed. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-10-21x86: Allow disabling IGD on Intel QueensbayBin Meng
Add a Kconfig option to disable the Integrated Graphics Device (IGD) so that it does not show in the PCI configuration space as a VGA disaplay controller. This gives a chance for U-Boot to run PCI/PCIe based graphics card's VGA BIOS and use that for the graphics console. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-10-20Merge git://git.denx.de/u-boot-marvellTom Rini
2015-10-21arm: mvebu: Enable DM_SERIAL on AXP / A38x boardsStefan Roese
This patch enables DM_SERIAL for all ARCH_MVEBU boards (AXP & A38x). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-10-21arm: mvebu: Enable DM_USB on AXP / A38x boardsStefan Roese
This patch enables DM_USB on the Marvell AXP / A38x eval boards. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-10-21arm: mvebu: Only set CONFIG_SKIP_LOWLEVEL_INIT for SPLStefan Roese
When running on the AXP I sometimes noticed a strange behavior. As some characters are not echoed on the U-Boot prompt. Not disabling the lowlevel_init code, especially calling cpu_init_cp15() in the main U-Boot seems to solve this issue. Signed-off-by: Stefan Roese <sr@denx.de>
2015-10-20sunxi: Use Kconfig CONFIG_MMCMaxime Ripard
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option will allow to enable or disable the support in each boards' defconfig. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-10-20sunxi: Add support for android boot imageMaxime Ripard
When using the fastboot boot command, the image sent to U-Boot will be an Android boot image. If the support is missing, that obviously won't work, so we need it in our configuration. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-10-20sunxi: Add a bootcmd_sunxi_compat to the default environment to boot old kernelsHans de Goede
Add a bootcmd_sunxi_compat value to the default environment when building with CONFIG_OLD_SUNXI_KERNEL_COMPAT, this way people who occasionally want to boot an old kernel can do so by simply typing "run bootcmd_sunxi_compat" rather then needing to have 2 separate setups / sdcards for old and new kernels. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-10-20sunxi: Switch to using malloc_simple for the splHans de Goede
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes, and .data from 0x54c to 0x144 bytes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-20sunxi: Enable CONFIG_SPL_STACK_RHans de Goede
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more room on the stack once we've the DRAM running. Besides being a good change to have on itself, this also paves the way for switching to using malloc_simple in the SPL which cuts of close to 4KiB of the SPL size. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-19sbc8641d: enable and test CONFIG_SYS_GENERIC_BOARDPaul Gortmaker
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-10-19sbc8641d: increase monitor size from 256k to 384kPaul Gortmaker
Between v2015.07-rc1 and v2015.07-rc2 this board started silent boot failure. A bisect led to commit 6eed3786c68c8a49d ("net: Move the CMD_NET config to defconfigs"). This commit looks harmless in itself, but it did implicitly add a feature to the image which led to this: u-boot$git describe 6eed3786c68c8a49d v2015.07-rc1-412-g6eed3786c68c ^^^ u-boot$ls -l ../41*/u-boot.bin -rwxrwxr-x 1 paul paul 261476 Oct 16 16:47 ../411/u-boot.bin -rwxrwxr-x 1 paul paul 266392 Oct 16 16:43 ../412/u-boot.bin u-boot$bc bc 1.06.95 Copyright 1991-1994, 1997, 1998, 2000, 2004, 2006 Free Software Foundation, Inc. This is free software with ABSOLUTELY NO WARRANTY. For details type `warranty'. 256*1024 262144 i.e. we finally broke through the 256k monitor size. Jump it up to 384k and fix the hard coded value used in the env offset at the same time. We were probably flirting with the 256k size issue without knowing it when testing on different baselines in earlier commits, but since this is all board specific, a rebase or reorder to put this commit 1st is of little value. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-10-19sbc8641d: set proper environment sector size.Paul Gortmaker
When debugging an env fail due to too small a malloc pool, it was noted that the env write was 256k. But the device sector size is 1/2 that, as can be seen from "fli" output: Bank # 1: CFI conformant flash (16 x 16) Size: 16 MB in 131 Sectors Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1888 Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 2 ms, buffer size: 64 bytes Sector Start Addresses: FF000000 E RO FF020000 E RO FF040000 E RO FF060000 E RO FF080000 E RO FF0A0000 E RO FF0C0000 E RO FF0E0000 E RO FF100000 E RO FF120000 E RO [...] FFF00000 RO FFF20000 RO FFF40000 RO FFF60000 RO FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 E RO FFFE8000 RO FFFF0000 E RO FFFF8000 RO => The desired env sector is FFF40000->FFF60000, or 0x20000 in length, just after the 256k u-boot image which starts @ FFF00000. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-10-19sbc8641d: increase malloc pool size to a sane defaultPaul Gortmaker
Currently the board fails to save its env, since the env size is much smaller than the sector size, and the malloc fails for the pad buffer, giving the user visible symptom of: Unable to save the rest of sector (253952) Allow for 1M malloc pool, the same as used on the sbc8548 board. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-10-19sbc8641d: enable command line editingPaul Gortmaker
It is just too painful to use interactively without it. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-10-19igep00x0: Use BCH8 ECCLadislav Michl
Used NAND chips requires at least 4-bit error correction, so use BCH8 as it is what kernel uses. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
2015-10-19vexpress64: Juno: Declare all 8GB of RAM and make them visible to the kernel.Liviu Dudau
Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel. Declare a secondary memory bank and set the sizes correctly. Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
2015-10-19ARM: dockstar: move start of environment areaEric Cooper
The default dockstar configuration for U-Boot currently causes it to overrun the environment area, so that a "saveenv" command bricks the device. This patch moves the environment to a higher address to avoid that. Signed-off-by: Eric Cooper <ecc@cmu.edu>
2015-10-16Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini
2015-10-15Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-10-15arm: vf610twr: improve memory layoutStefan Agner
Currently, the device tree relocation is disabled, likely to keep some DDR3 RAM at the end for Cortex-M4 firmwares. This can be archived using bootm_size, which limits the image processing range of the boot commands. Move the device tree standard load address to a higher address which aligns better with what we are doing on other boards. Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2015-10-13odroid: Add boot script (boot.scr) supportGuillaume GARDET
Add boot script (boot.scr) support. If no boot script are found, it boots as usual. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Tested-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-10-13odroid: replace 'fatload' with 'load' to be able to use EXT* partitionsGuillaume GARDET
Replace 'fatload' command by 'load', to be able to use EXT* partitions while keeping FAT partition compatibility. Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Tested-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-10-11pcm052: fix MTD partitioningAlbert ARIBAUD (3ADEV)
MTD partitioning in current pcm052 configuration is inconsistent. Fix it across MTDPARTS_DEFAULT, CONFIG_EXTRA_ENV_SETTINGS, and CONFIG_ENV_OFFSET[_REDUND]. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-10-11arndale: Apply Cortex-A15 errata #773022 and #774769Ian Campbell
We run 4 Arndale boards in our automated test framework, they have been running quite happily for quite some time using a Debian Wheezy userspace. However when upgrading to a Debian Jessie we started seeing frequent segmentation faults from gcc when building the kernel, to the extent that it is unable to successfully build the kernel twice in a row, and often fails on the first attempt. Searching around I found https://bugs.launchpad.net/arndale/+bug/1081417 which pointed towards http://www.spinics.net/lists/kvm-arm/msg03723.html and CPU Errata 773022 and 774769. This errata needs to be applied to all processors in an SMP system, meaning that the usual strategy of applying them in arch/arm/cpu/armv7/start.S is not appropriate (since that applies to the boot processor only). Instead we apply these errata in the secure monitor which is code that is traversed by all processors as they are brought up. The net affect on Arndale is that ACTLR changes from 0x40 to 0x2000042. I ran 17 kernel compile iterations overnight with no segfaults. Runtime testing was done on our v2014.10 based branch and forward ported (with only minimal and trivial contextual conflicts) to current master, where it has been build tested only. I suppose in theory these errata apply to any Exynos5250 based boards, but Arndale is the only one I have access to and I have therefore chosen to be conservative and only apply it there. Also, reorder CONFIG_ARM_ERRATA_794072 in README to make the list numerically sorted. Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
2015-10-11ppc4xx: Remove lcd4_lwmon5 supportStefan Roese
This platform has not gone into production. So lets remove it. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-11ppc4xx: Convert lwmon5 board to generic boardStefan Roese
Add CONFIG_SYS_GENERIC_BOARD to lwmon5.h and CONFIG_DISPLAY_BOARDINFO to Kconfig file. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-11Revert "powerpc: ppc4xx: remove lwmon5 support"Stefan Roese
This reverts commit 8fe11b8901a31d11990488c82bc23612589d57be. I'll add support to lwmon5 in the next patch and will remove support for the broken lcd4_lwmon5 as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-11ti: omap3: config: remove 1 from boolean defineIgor Grinberg
CONFIG_TWL4030_POWER is a boolean define variable. It is either defined or not defined and should not have a value assigned to it. Remove the value. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2015-10-11vexpress64: juno: use /dev/sda2Ryan Harkin
This patch changes the default "root=" parameter to "/dev/sda2". Many linux based distros use /dev/sda1 for their boot partition; this is often not a rootfs that can be used by the "root=" parameter. Linaro images use /dev/sda1 as a boot partition, although this of a different nature to a distro image. Linaro uses /dev/sda2 for the rootfs partition. Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-11vexpress64: juno: add alternate kernel and device tree filenamesRyan Harkin
The latest Juno firmware stores the files in NOR flash as "norkern" for kernel binary, "board.dtb" for the device tree binary. The "old" firmware used the name "Image" for the kernel binary and "juno" for the device tree binary. Rather than just change the default U-Boot configuration to use the new names, breaking users with the old firmware, attempt to load the default filename first. If that fails, attempt to load the alternate filename. I've echo'd that we are loading the alternate file to counter the output from "afs load" shown if the first load attempt fails. For example, I see output like this on my Juno board when it's configured the with the "old" firmware: image "norkern" not found in flash Loading Image instead of norkern loaded region 0 from 08500000 to 80000000, 00AB6318 bytes image "board.dtb" not found in flash Loading juno instead of board.dtb loaded region 0 from 0A000000 to 83000000, 00003188 bytes Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-11vexpress64: juno: add optional initrdRyan Harkin
Some OS images require an initrd on Juno. If the file ramdisk.img exists in NOR flash, then we load it and pass the address to the kernel. Otherwise, we pass the "-" parameter as before. Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-11vexpress64: juno: add androidboot.hardware=junoRyan Harkin
Linaro's Juno Android builds requires the androidboot.hardware parameter be set to a know board name. Non-Android kernels ignore this extra parameter because they don't contain code to parse it. Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-11vexpress64: fvp dram: add DRAM configurationRyan Harkin
Create an additional FVP configuration to boot images pre-loaded into DRAM. Sometimes it's preferential to boot the model by loading the files directly into DRAM via model parameters, rather than using SemiHosting. An example of model parmaters that are used to pre-load the files into DRAM: --data cluster0.cpu0=Image@0x80080000 \ --data cluster0.cpu0=fvp-base-gicv2-psci.dtb@0x83000000 \ --data cluster0.cpu0=uInitrd@0x84000000 Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> [trini: Update board/armltd/vexpress64/Kconfig logic] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-11vexpress64: increase max gunzip sizeRyan Harkin
vexpress64 kernels are usually over 8 MBytes in length, so setting the max uImage length to 64 Mbytes should give us plenty of scope for expansion. I mostly chose this length to match other board configs that use "(64 << 20)". Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-11vexpress64: fix checkpatch warningsRyan Harkin
This patch fixes a couple of checkpatch warnings on the vexpress64 config. Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-11configs: ls1021atwr: Enable DSPI for LS1021ATWRYao Yuan
DSPI2 can be verified when boot from QSPI now. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-10-02Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
generated by cgit (git 2.34.1) at 2025-01-16 14:43:27 +0000