summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2019-02-14arm64: zynqmp: Fix logic around CONFIG_ZYNQ_SDHCIMichal Simek
Replace SDHCI controller listing by Kconfig symbol to let SPL know that this board is using multiple SDHCIs controllers. Kconfig help message should explain why this is needed. Origin symbols were used in full u-boot but with moving to distro boot this was fixed already. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14arm64: zynqmp: Switch all platforms to DM_I2CMichal Simek
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio subsystem already. That's why also remove CMD_PCA953X which is only for this driver. zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address. DM_I2C is not enabled for the whole SoC because it increase size for mini configurations and there is no I2C symbol present to setup dependencies. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-02-14ARM: zynq: Convert dlc20 and zc70x board to DM_I2CMichal Simek
All these board have also eeprom enabled that's why it is also enabled via defconfig. There is also no need to have zc70x specific config file that's why also remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-02-14ARM: zynq: Convert Syzygy to DM_I2CMichal Simek
Boards have only one controller enabled that's why move to DM_I2C is easy. Add also i2c alias for not to be shown as i2c bus -1 because alias doesn't exist. Config file points to MAC stored in eeprom but it is not listed that's why I have added 24c08 part. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-02-14arm64: versal: Add mini configuration for VersalSiva Durga Prasad Paladugu
This patch adds new mini target for versal. This configuration is very minimal in size which runs from OCM. It contains support for mtest which can be used for running DDR memory tests. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14arm64: versal: Define distro boot commnads for qspi ospi and mmcSiva Durga Prasad Paladugu
This patch adds distro boot commands for qspi, ospi and mmc. The distro boot commands now reads the script from flash offset of 63.5MB for qspi and ospi and executes it. For mmc its same as generic distro boot command. As either one of the qspi or ospi can exist on hardware, defined a single distroboot command as xspi that works for both. Setup default location via script_offset_f to 63.5MB to match the most xilinx reference boards for qspi, ospi for now. 512kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14arm: zynq: Define distro boot commnads for qspi, nand and norSiva Durga Prasad Paladugu
This patch adds distro boot commands for qspi, nand and nor. The distro boot commands now reads the script from flash offset of 15.75MB and executes it. Setup default location via script_offset_f to 15.75MB to match the most xilinx reference boards for qspi, nand and set the same using script_offset_nor to 0xE2EC0000 for nor. 256kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14arm64: versal: Add mini eMMC configurationSiva Durga Prasad Paladugu
This patch adds mini eMMC configuration which has only emmc0 and emmc1 functionalities and can run from small amount of memory. This is required for memory constraint devices. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14xilinx: Move zynq_board_read_rom_ethaddr to shared locationMichal Simek
Zynq and ZynqMP are sharing similar code and there is no reason to do code duplication. Move zynq_board_read_rom_ethaddr() to common file for easier conversion to DM. Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy which is only one Zynq board which is using this feature. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14arm64: zynqmp: Define distro boot commnads for qspi and nandSiva Durga Prasad Paladugu
This patch adds distro boot commands for qspi and nand. The distro boot commands now reads the script from flash offset of 63.5MB and executes it. Setup default location via script_offset_f to 63.5MB to match the most xilinx reference boards. 512kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14ARM: zynq: Run distribution boot commands firstMichal Simek
This patch is doing two things. 1. Exchanging order of boot commands. distro_bootcmd is run first followed by Xilinx boot command. 2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by creating Xilinx distribution bootcommand and wiring it as the last bootcommand. QSPI, NAND distribution boot command will be added later. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-10Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dmTom Rini
Samsung sound patches (applied for Samsung maintainer) Common sound support buildman environment support of-platdata documentation improvements
2019-02-09Convert CONFIG_BOARD_TYPES to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_BOARD_TYPES Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2019-02-09am65x_evm: Allow bootm to load larger kernelsAndrew F. Davis
Bootm will fail to load kernels over 8MB, this is not enough for our 64bit kernel images. Increase this to 64MB. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-02-09bcm963158: add initial supportPhilippe Reynes
This add the initial support of the broadcom reference board bcm963158 with a bcm63158 SoC. This board has 1 GB of ram, 512 MB of flash (nand), 2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN). Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09omap3_cairo: remove empty #ifdef/#endif blockChris Packham
The content between these guards was removed in commit 9baa2bce2890 ("Removed unused references to CONFIG_SERIALx"). Remove the now empty #ifdef/#endif block and the accompanying comment. Signed-off-by: Chris Packham <judge.packham@gmail.com>
2019-02-07Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
- SPI-NOR support
2019-02-07configs: Don't use SPI_FLASH_BAR as defaultVignesh R
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07configs: Remove SF_DUAL_FLASHVignesh R
SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above enums yield no user and therefore support seems to be incomplete. Remove these configs so as to avoid confusion. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07configs: Move CONFIG_SPI_FLASH into defconfigsVignesh R
Completely move CONFIG_SPI_FLASH from remaining board header files to defconfigs Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-05arm: mvebu: theadorable: Enable video / LCD support with the new DM driverStefan Roese
With the new DM_VIDEO support in the Armada XP LCD driver, this patch adds the needed DT node for the LCD controller to the theadorable dts file. This DT property is not added to the Armada XP dtsi files, as this LCD feature is pretty unusual for this SoC and I personally know of no other board that uses this controller. This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp command supported these BMP files. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2019-02-05pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfigStefan Roese
This patch adds DM_PCI support to the MVEBU PCIe driver. This is necessary, since all PCI drivers have to be moved to DM (driver model) until the v2019.07 release. To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU from config headers to the defconfig files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: Marek Behún <marek.behun@nic.cz> Cc: VlaoMao <vlaomao@gmail.com>
2019-02-02Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchipTom Rini
u-boot-rockchip changes for 2019.04-rc1: * support for Chromebook Bob * full pinctrl driver using DTS properties * documentation improvements * I2S support for some Rockchip SoCs
2019-02-02Merge tag 'mips-pull-2019-02-01' of git://git.denx.de/u-boot-mipsTom Rini
- MIPS: mscc: jr2: small fixes - MIPS: mscc: luton: add ethernet and switch driver - MIPS: mt76xx: fix timer frequency
2019-02-02Kconfig: Migrate CONFIG_BUILD_TARGETJagan Teki
Migrate CONFIG_BUILD_TARGET into Kconfig. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-02-01rockchip: Add support for chromebook_bobSimon Glass
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports for both power and external display. It includes a Chrome OS EC (Cortex-M3) to provide access to the keyboard and battery functions. Support so far includes only: - UART - SDRAM - MMC, SD card - Cros EC (but not keyboard) Not included: - Keyboard - Display - Sound - USB - TPM Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support for this is not provided in this series. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: rk3399: Add ROCKCHIP_DEVICE_SETTINGS to set envSimon Glass
Some boards use different stdio environment variables from the default. Provide a #define for this which can be set before including the header file. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4Tien Fong Chee
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FATTien Fong Chee
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01mips: mt76xx: Use correct timer frequencyStefan Roese
Testing has shown that the timer on the MT7688 platforms does not run correctly (too fast timeout). This patch changes CONFIG_SYS_MIPS_TIMER_FREQ from 200MHz to 290MHz which is the correct value, as its also used in Linux. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-31configs: meson64: use vidconsole and usbkbd if enabledNeil Armstrong
Allows displaying the console via video and using a USB keyboard. Also enables CONFIG_SPLASH_SCREEN if using video. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-30Merge tag 'u-boot-imx-20190129' of git://git.denx.de/u-boot-imxTom Rini
For 2019.04
2019-01-28arm: imx7s-warp: Convert to DM PMICBryan O'Donoghue
This patch converts the warp7 and warp7_bl33 board ports over to using the DM PMIC model. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28warp7: defconfig: Switch to DM for I2CBryan O'Donoghue
This commit switches to DM I2C for warp7 and warp7_bl33 defconfigs. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28imx8qxp: mek: default enable SPLPeng Fan
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT. The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK. Note: SPL FIT could not support secure boot chain, because i.MX8/8X only support i.MX container format. This container format has not been upstreamed, so we use FIT for now. When SPL container supported, we could switch to that. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28colibri_imx7: fix boot commandsStefan Agner
Fix mixed up boot commands between raw NAND and eMMC variant. Also make sure that the boot_file is defined for the eMMC boot command. Fixes: a62c60610f51 ("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support") Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-01-28m53menlo: fix addmtd cmd in default environmentOlaf Mandel
The original definition added the string mtdparts= to the Linux Kernel args twice: mtdparts=mtdparts=. Fix that. Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com> Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-28m53menlo: fix splashfile locationOlaf Mandel
After merging the boot partition into the root partition, the splashfile resides in the /boot subdirectory: update the default environment to reflect that. Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com> Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-28pico-imx7d: Add LCD supportFabio Estevam
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-01-28imx: Add PHYTEC phyBOARD-i.MX6UL-SeginMartyn Welch
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on the PHYTEC phyCORE-i.MX6UL SOM (PCL063). CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR Board: PHYTEC phyCORE-i.MX6UL I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC0 Working: - Eth0 - i2C - MMC/SD - NAND - UART (1 & 5) - USB (host & otg) Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2019-01-26PowerPC: Stop re-using CONFIG_SPL_TEXT_BASE for TPLTom Rini
Rather than checking for CONFIG_TPL_BUILD and then re-defining CONFIG_SPL_TEXT_BASE make use of CONFIG_TPL_TEXT_BASE directly. Cc: York Sun <york.sun@nxp.com> Cc: Po Liu <po.liu@nxp.com> Cc: Qiang Zhao <qiang.zhao@nxp.com> Cc: Timur Tabi <timur@tabi.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-26Merge branch '2019-01-25-master-imports'Tom Rini
- snapdragon 820c improvements - poplar updates - DFU + SPL cleanups - Improve the mediatek mmc driver - Other minor cleanups / improvements
2019-01-26ARM: mach-omap2: Kconfig: Allow OMAP5 devices to set entry pointAndrew F. Davis
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to have an non-standard boot address in memory. This may be due to the device being a high security variant, which place the Initial SoftWare (ISW) after certificates and secure software. Allow these devices to set this from Kconfig. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-01-26spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFUAndrew F. Davis
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT to allow for cleaner use in code. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-25configs: Migrate CONFIG_DFU_MMC againTom Rini
A few platforms recently added in CONFIG_DFU_MMC under include/configs rather than via the defconfig, update them. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-25Merge tag 'arc-fixes-for-2019.04-rc1' of git://git.denx.de/u-boot-arcTom Rini
A couple of trivial fixes and improvements for ARC Most notable are: * Move of ENV_SIZE/ENV_OFFSET to Kconfig * Fix with private structure allocation for arc_uart * Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
2019-01-25ARC: Move ENV_SIZE and ENV_OFFSET to KconfigAlexey Brodkin
Join the party of some ARM boards and drop more items from include/configs/xxx.h. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-25serial: Get rid of CONFIG_DW_SERIALAlexey Brodkin
CONFIG_DW_SERIAL is no longer used anywhere so let's forget about it. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@konsulko.com> Cc: Adam Ford <aford173@gmail.com> Cc: Mario Six <mario.six@gdsys.cc> Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Cc: Alex Kiernan <alex.kiernan@gmail.com> Cc: "Jorg Krause" <joerg.krause@embedded.rocks> Cc: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-24Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-01-24ARM: zynq: Disable i2c for Zybo/Zybo Z7Michal Simek
There is no i2c connected in base DT that's why disable I2C commands. Also remove zynq_zybo which is not needed now. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-05 00:14:07 +0000