summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2009-03-09Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
Conflicts: lib_ppc/board.c Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-0583xx, kmeter1: updates for 2009.03Heiko Schocher
- HRCW update HRCWH_BOOTSEQ_DISABLE not HRCWH_BOOTSEQ_NORMAL HRCWH_LALE_EARLY added - DDR-SDRAM settings modified. This solves sporadically problems with this memory. - CS1 now 128 MB window size - CS3 now 512 MB window size - PRAM activated - MTDPARTS_DEFAULT defined - CONFIG_HOSTNAME added - MONITOR_LEN now 384 KB Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-0583xx, kmeter1: autodetect size of DDR II RAMHeiko Schocher
it is possible that some board variants have different DDR II RAM sizes. So we autodetect the size of the assembled RAM. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-0583xx, kmeter1: add I2C, dtt, eeprom supportHeiko Schocher
This patch adds I2C support for the Keymile kmeter1 board. It uses the First I2C Controller from the CPU, for accessing 4 temperature sensors, an eeprom with IVM data and the booteeprom over a pca9547 mux. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05MPC8349ITX: several config issues fixedValeriy Glushkov
The previous version rebooted forever with DDR bigger than 256MB. Access the DS1339 RTC chip is on I2C1 bus. Allow DHCP. Signed-off-by: Valeriy Glushkov <gvv@lstec.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-24Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk
2009-02-24Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2009-02-24ARM: add an "eet" variant of the imx31_phycore boardGuennadi Liakhovetski
The "eet" variant of the imx31_phycore board has an OLED display, using a s6e63d6 display controller on the first SPI interface, using GPIO57 as a chip-select for it. With this configuration you can display 256 colour BMP images in 16-bit RGB (RGB565) LCD mode. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-24LCD: support 8bpp BMPs on 16bpp displaysGuennadi Liakhovetski
This patch also simplifies some ifdefs in lcd.c, introduces a generic vidinfo_t, which new drivers are encouraged to use and old drivers to switch over to. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2009-02-24A driver for the S6E63D6 SPI display controller from SamsungGuennadi Liakhovetski
This is a driver for the S6E63D6 SPI OLED display controller from Samsung. It only provides access to controller's registers so the client can freely configure it. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2009-02-24i.MX31: add a simple gpio driverGuennadi Liakhovetski
This is a minimal driver, so far only managing output. It will be used by the mxc_spi.c driver. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-23mpc83xx: MPC837XERDB: Add PCIe supportAnton Vorontsov
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe slots. Let's support them. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-23PCI: Add pci_last_busno() helperAnton Vorontsov
This is just a handy routine that reports last PCI busno: we walk down all the hoses and return last hose's last_busno. Will be used by PCI/PCIe initialization code. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-23MPC86xx: set CONFIG_MAX_MEM_MAPPED to 2G by defaultBecky Bruce
Currently, we get 256MB as the default, but since all the 86xx board configs define a 2G BAT mapping for RAM, raise default to 2G. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
2009-02-23Merge branch 'master' of git://git.denx.de/u-bootKim Phillips
2009-02-22netloop: speed up NetLoopHeiko Schocher
NetLoop polls every cycle with getenv some environment variables. This is horribly slow, especially when the environment is big. This patch reads only the environment variables in NetLoop, when they were changed. Also moved the init part of the NetLoop function in a seperate function. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-02-22ARM: synchronize mach-types.h with linux v2.6.29-rc5-315-g683fdc5Wolfgang Denk
The file was generated from building versatile_defconfig. Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-22Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2009-02-22Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-02-22MIPS: Fix GCC-4.2 'discards qualifiers from pointer target type' warningsShinya Kuribayashi
Compiling dbau1x00 and gth2 boards with GCC-4.2, you would see new warnings like this: skuribay@ubuntu:u-boot.git$ ./MAKEALL dbau1000 Configuring for dbau1x00 board... au1x00_eth.c: In function 'au1x00_send': au1x00_eth.c:158: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type au1x00_eth.c: In function 'au1x00_recv': au1x00_eth.c:211: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type au1x00_eth.c: In function 'au1x00_init': au1x00_eth.c:252: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type au1x00_eth.c: In function 'au1x00_recv': au1x00_eth.c:211: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type au1x00_eth.c: In function 'au1x00_init': au1x00_eth.c:252: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type au1x00_eth.c: In function 'au1x00_send': au1x00_eth.c:158: warning: passing argument 1 of 'virt_to_phys' discards qualifiers from pointer target type We're passing a volatile pointer to a function which is expecting a non- volatile pointer. That's potentially dangerous, so gcc warns about it. Confirmed with ELDK 4.2 (GCC 4.2.2) and Sourcey G++ 4.2 (GCC 4.2.3). To fix this, we add a volatile attribute to the argument in question. The virt_to_phys function in Linux kernel also does the same thing. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2009-02-22OMAP3: Clean up MMC codeDirk Behme
Clean up OMAP3 MMC code: * Convert register access to struct & readx/writex style * Replace hardcode values by macros * Remove macro defined twice Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22OMAP3: Add OMAP3 auto detectionDirk Behme
This patch adds OMAP3 cpu type auto detection based on OMAP3 register and removes hardcoded values. Signed-off-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22OMAP3: Beagle: Add board revision detectionDirk Behme
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX) which might need different software handling. For this, GPIO pin 171 (GPIO module 6, offset 11) can be used to check for board revision. If this pin is low, we have a rev C board. Else it must be a revision Ax or Bx board. To handle board differences you can call function beagle_get_revision(). E.g.: if (beagle_get_revision()) { /* do special revision C stuff here */ } Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22nmdk8815: fix onenand supportJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22arm: add uart dcc supportJean-Christophe PLAGNIOL-VILLARD
Serial driver via the EmbeddedICE macrocell's DCC channel using co-processor 14. It does include a timeout to ensure that the system does not totally freeze when there is nothing connected to read. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22Enable Ethernet for Nomadik 8815 Evaluation KitAlessandro Rubini
This trivially enables Ethernet support in the debug board by setting up the proper chip select. Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22Nand driver for Nomadik SoCAlessandro Rubini
This driver implements the ECC algorithm described in the CPU data sheet and uses the OOB layout chosen in already-released development systems (shipped with a custom-made u-boot 1.3.1). Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22Added nomadik.h headerAlessandro Rubini
Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-21Blackfin: bf537-stamp: fix I2C board definesMike Frysinger
The previous merge for cleaning up the I2C driver incorrectly reverted the CFG_xxx rename for some of the I2C defines. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-21Enable ext2 support for TQM8xxL/M based boardsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-20pxa: move mmc drivers to drivers/mmcJean-Christophe PLAGNIOL-VILLARD
introduce new macro CONFIG_PXA_MMC to activate it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20pxa: fixing get_timer to return time in miliseconds.Micha Kalfon
Fixing the get_timer function to return time in miliseconds instead of ticks. Also fixed PXA boards to use the conventional value of 1000 for CONFIG_SYS_HZ. Signed-off-by: Micha Kalfon <smichak.uv@gmail.com>
2009-02-1982xx, mgcoge: updates for 2009.03Heiko Schocher
- activate CS4 for accessing the FPGA - activate Rx buf len > 1 on SMC - pram activated - MTDPARTS_DEFAULT defined - update the size of the flashes in the DTS before booting Linux - MONITOR_LEN updated to 384k - added CONFIG_HOSTNAME - added CONFIG_ENV_BUFFER_PRINT - Environment size reduced to 16k Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-198xx, mgsuvd: updates for 2009.03Heiko Schocher
- activate Rx buf len > 1 on SMC - pram activated - MTDPARTS_DEFAULT defined - update the size of the flash in the DTS before booting Linux - MONITOR_LEN updated to 384k - added CONFIG_HOSTNAME - added CONFIG_ENV_BUFFER_PRINT - Environment size reduced to 16k Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19Merge branch 'master' of git://git.denx.de/u-bootKim Phillips
2009-02-19Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2009-02-19Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-02-19Create configuration option for restricted ns16550 functionsRon Madrid
This patch will create a configuration option for a minimum configuration for the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new configuration option to the SIMPC8313.h config file in order to fix the NAND bootstrap build error. This option will exclude all functions with exception of NS16550_putc and NS16550_init. This will be used primarily to save space and remove unused code from builds in which space is limited. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
2009-02-18ppc4xx: Update PMC405 board supportMatthias Fuchs
This patch prepares the good old PMC405 board support for upcoming PMC405V2 patches. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18ppc4xx: Cleanup PMC405 board supportMatthias Fuchs
This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18qong: changes to Dave/DENX Qong configurationIlya Yanok
1. Changes to the default environment: - "bootcmd" defined as "run flash_self" - "saveenv" command removed from "update" - "uboot" changed to "u-boot" (also in "load") - "addmtd" variable defined (and added to all boot commands) 2. CONFIG_CMD_JFFS2 defined to enable "mtdparts" command 3. MTDIDS_DEFAULT and MTDPARTS_DEFAULT defined 4. CONFIG_SYS_CBSIZE changed from 256 to 512. That solves the problem with truncated "bootargs" environment variable. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-02-18include/image.h: Ease grepping of image_* functionsPetri Lehtinen
Because the functions have been defined using macros, grepping for their definitions is not possible. This patch adds the real function names in comments. Signed-off-by: Petri Lehtinen <petri.lehtinen@inoi.fi> Acked-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENVMike Frysinger
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command rather than a generic "env" command, or anything else related to the environment. So, let's make sure the define is named accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18disable imls command if no flash is definedValeriy Glushkov
Default CONFIG_CMD_IMLS must be disabled when CONFIG_SYS_NO_FLASH is defined Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
2009-02-18API: Improve glue mid-layer of the API demo application.Rafal Jaworowski
- Extend ub_dev_read() and ub_dev_recv() so they return the length actually read, which allows for better control and error handling (this introduces additional error code API_ESYSC returned by the glue mid-layer). - Clean up definitions naming and usage. - Other minor cosmetics. Note these changes do not touch the API proper, so the interface between U-Boot and standalone applications remains unchanged. Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
2009-02-17TQM8260: fix locations of kernel and ramdisk images in flashWolfgang Denk
After introducing redundant environment the kernel images was overlapping with environment. Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-1683xx: add missing TIMING_CFG1_CASLAT_* definesHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-16mpc8349itx: allow SATA boot from the onboard SIL1334Valeriy Glushkov
This patch allows using of SATA devices connected to the onboard PCI SIL1334 SATA controller. Signed-off-by: Valeriy Glushkov <gvv@lstec.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-1683xx: Add eSDHC support on 8379 EMDS boardAndy Fleming
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-1685xx: Add eSDHC support for 8536 DSAndy Fleming
Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-28 20:51:03 +0000