summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2013-07-26omap3_beagle: enable CMD_FS_GENERIC and simplify load of image/ramdiskNishanth Menon
CMD_FS_GENERIC allows us to simplify where we load up our image from either from ext2/fat etc. So, lets use that instead of cumbersome options we currently use. Sticking with existing conventions, defaults will be: ramdisk=ramdisk.gz bootpart=0:2 (second partition) bootdir=/boot (/boot in second partition) This matches with the default behavior, these can be overriden by env files as needed. Signed-off-by: Nishanth Menon <nm@ti.com>
2013-07-26omap3_beagle: replace uImage.beagle with generic uImageNishanth Menon
e682930867f7dfc4a01784fe452fad9e962d65a (BeagleBoard: config: use uImage.beagle for tftp) Introduced uImage.beagle which does not happen to be default output file of Linux kernel build make uImage (output is uImage). So, replace uImage.beagle with uImage Signed-off-by: Nishanth Menon <nm@ti.com>
2013-07-26omap3_beagle: remove JFFS2 support.Nishanth Menon
We do not use JFFS2 by default and it conflicts with CONFIG_CMD_FS_GENERIC (ls command is the same). Since most of our BOOTCMD can be simplified by using the FS_GENERIC, dropping JFFS2 Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Joel Fernandes <joelf@ti.com>
2013-07-26ARM: DRA7xx: Enable CPSW Ethernet supportMugunthan V N
Enabling CPSW Ethernet support in DRA7xx EVM. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26drivers: net: cpsw: remove hard coding bd ram for cpswMugunthan V N
BD ram address may vary in various SOC, so removing the hardcoding and passing the same information through platform data Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26am335x_evm: Correct CONFIG_CMD_SPL_WRITE_SIZETom Rini
We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion of falcon mode to NAND. Previously it was half the size of the eraseblock which is too small, increase to eraseblock size. Signed-off-by: Tom Rini <trini@ti.com>
2013-07-26am335x_evm: Update eMMC falcon mode locationsTom Rini
The previous location used for the "args" portion of falcon mode was too small to allow for a device tree to be saved there, so move the location slightly and increase the size. In addition, our previous kernel location was part of the area we set aside for U-Boot itself, so move it up a bit higher. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-07-26am335x_evm: Correct DFU ALT settings for falcon modeTom Rini
Now that we have falcon mode enabled, the partiton numbers for NAND have changed, and we need to list entries for updating these parts of the system. While adding falcon mode entires for eMMC (raw), we round up the limit on U-Boot for ease of math later. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
2013-07-25Merge branch 'u-boot/master' into u-boot-arm/masterAlbert ARIBAUD
2013-07-25Merge branch 'master' of git://git.denx.de/u-boot-nds32Tom Rini
2013-07-25qemu-malta: Update for SPDX license identifiersTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-25Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini
Conflict over SPDX changes means that one change was effectively dropped as it was fixing typos in a removed hunk of text. Conflicts: arch/mips/cpu/mips64/start.S Signed-off-by: Tom Rini <trini@ti.com>
2013-07-25highbank: enable keyed autoboot stopRob Herring
Restrict autoboot interruption to "s" or "d" keys. This will prevent some unwanted stopping and also allow disabling the reset on command timeout. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25ARM: highbank: setup peripherals based on power domain statusRob Herring
Accessing powered down peripherals will hang the bus, so check power domain status before initializing SATA and fixup the FDT to disable unused peripherals. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25ARM: highbank: enable reset on command timeoutRob Herring
Enable resetting on command timeout. The timeout is set with environment setting bootretry. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25ARM: highbank: update config optionsRob Herring
Various changes to highbank config: Enable EFI partitions Enable ext4 and FAT filesystems Enable bootz command and raw initrd Increase cmd and print buffer size to 1K Change serial baudrate to 115200 Enable hush shell Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-24MIPS: qemu-malta: bring up ethernetGabor Juhos
Qemu emulates a PCNET PCI card for the Malta CoreLV board. Enable the pcnet driver and add board specific ethernet initialization function to bring it up. Also enable the CONFIG_CMD_NET and CONFIG_CMD_PING options. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24MIPS: qemu-malta: add PCI supportGabor Juhos
Qemu emulates the Galileo GT64120 System Controller which provides a CPU bus to PCI bus bridge. The patch adds driver for this bridge and enables PCI support for the emulated Malta board. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24MIPS: qemu-malta: enable flash supportGabor Juhos
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24MIPS: qemu-malta: add support for emulated MIPS Malta boardGabor Juhos
Add minimal support for the MIPS Malta CoreLV board emulated by Qemu. The only supported peripherial is the UART. This is enough to boot U-Boot to the command prompt both in little and big endian mode. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24MIPS: import gt64120.h header from LinuxGabor Juhos
The Linux specific register access macros, the extern function declarations and the UL suffixes has been removed. The header file will be used for the qemu-malta board. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24Add eCos-2.0 SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-07-24Add LGPL-2.1+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24nds32: Enable the function of passing parameters to Linuxken kuo
Add a header file, setup.h, which copy from Linux source code, this file contain structures are used to pass initialisation parameters to Linux. Enable this function on adp-ag101/adp-ag101p target Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com> Cc: Macpaul Lin <macpaul@gmail.com>
2013-07-24nds32: Enable SDIO and EXT2 command support for Andes boardken kuo
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com> Cc: Macpaul Lin <macpaul@gmail.com>
2013-07-24nds32: Enable two banks of SDRAM on Andes boardken kuo
The original adp-ag101/adp-ag101p initialize only one bank(64MB) by default at boot time, but it is not enough for some application, so increasing to two banks(128M). Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com> Cc: Macpaul Lin <macpaul@gmail.com>
2013-07-24pci: move pci_ftpci100.h to include/faraday/ftpci100.hGabor Juhos
Even though the header files is used only by the pci_ftpci100 driver, it contains declaration for a function which is used by external code. Move the header file to a common location which lets external code use it. Compile tested only. Cc: Macpaul Lin <macpaul@andestech.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
2013-07-24block: constify sect_buf argument of ide_write_dataGabor Juhos
Add a const keyword to the sect_buf argument of ide_write_data to fix the following warning: cmd_ide.c: In function '__ide_output_data': cmd_ide.c:548: warning: passing argument 2 of 'ide_write_data' discards qualifiers from pointer target type /devel/u-boot.git/include/ide.h:76: note: expected 'ulong *' but argument is of type 'const ulong *' Also modify the driver-model documentation to match with the new prototype. Compile tested only. Cc: Macpaul Lin <macpaul@andestech.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
2013-07-23fdtdec: Add compatible string for High speed i2cnaveen krishna chatradhi
Adds a new COMPAT string exynos5-hsi2c for high speed i2c controller available on exynos5 SoCs from Samsung. Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
2013-07-23vf610: Add I2C support for Vybrid VF610 platformAlison Wang
This patch adds I2C support for Vybrid VF610 platform and adds I2C0 support to VF610TWR board. Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23arm/km: fix u-boot update functionalityHolger Brunck
Due to the new I2C framework we need to adapt the u-boot update function. Due to the new framework all i2c leafs behind a mux are present in the system and not only those who are defined and used. So it is bus number 5 after the rework. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
2013-07-23i2c, ppc4xx_i2c: switch to new multibus/multiadapter supportDirk Eibach
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Heiko Schocher <hs@denx.de> Cc: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
2013-07-23tegra: i2c: Enable new CONFIG_SYS_I2C frameworkSimon Glass
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra i2c driver to support this. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Heiko Schocher <hs@denx.de>
2013-07-23i2c, multibus, keymile: get rid of EEprom_ivm envvariableHeiko Schocher
as the keymile boards use now the new i2c multibus/multiadapter framework, remove the EEprom_ivm Environmentvar, as not longer needed. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Holger Brunck <holger.brunck@keymile.com> Tested-By: Holger Brunck <holger.brunck@keymile.com>
2013-07-23i2c, multibus: get rid of CONFIG_I2C_MUXHeiko Schocher
CONFIG_I2C_MUX is replaced through the new i2c multibus/multiadapter framework, configured through CONFIG_SYS_I2C. As CONFIG_I2C_MUX is only used on the keymile boards, and they are now completely moved to the new framework, remove CONFIG_I2C_MUX. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Holger Brunck <holger.brunck@keymile.com> Tested-By: Holger Brunck <holger.brunck@keymile.com>
2013-07-23i2c, fsl_i2c: switch to new multibus/multiadapter supportHeiko Schocher
- added to fsl_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23i2c, soft-i2c: switch to new multibus/multiadapter supportHeiko Schocher
- added to soft_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23i2c: common changes for multibus/multiadapter supportHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org> Cc: Henrik Nordström <henrik@henriknordstrom.net>
2013-07-23i2c: add i2c_core and prepare for new multibus supportHeiko Schocher
This Patch introduce the new i2c_core file, which holds the I2C core functions, for the rework of the multibus/ multiadapter support. Also adds changes in i2c.h for the new I2C multibus/multiadapter support. This new support can be activated with the CONFIG_SYS_I2C define. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-19arm:trats:fix: Correction of loaddtb environment variable.Łukasz Majewski
Missing space for loaddtb command has been added. When missing, ext4load fails with wrong number of passed parameters. Acked-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2013-07-16mpc85xx: Add gdsys ControlCenter Digital boardDirk Eibach
The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC. It boots from SPI-Flash but can be configured to boot from SD-card for factory programming and testing. On board peripherals include: - 2x GbE - Lattice ECP3 FPGA connected via PCIe - mSATA RAID1 - USB host - DisplayPort video output - Atmel TPM Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16tpm: add AUTH1 cmds for LoadKey2 and GetPubKeyReinhard Pfau
Extend the tpm library with support for single authorized (AUTH1) commands as specified in the TCG Main Specification 1.2. (The internally used helper functions are implemented in a way that they could also be used for double authorized commands if someone needs it.) Provide enums with the return codes from the TCG Main specification. For now only a single OIAP session is supported. OIAP authorized version of the commands TPM_LoadKey2 and TPM_GetPubKey are provided. Both features are available using the 'tpm' command, too. Authorized commands are enabled with CONFIG_TPM_AUTH_SESSIONS. (Note that this also requires CONFIG_SHA1 to be enabled.) Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc> Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Acked-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-15Fix ext2/ext4 filesystem accesses beyond 2TiBFrederic Leroy
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type, which is required to represent block numbers for storage devices that exceed 2TiB (the block size usually is 512B), e.g. recent hard drives We now use lbaint_t for partition offset to reflect the lbaint_t change, and access partitions beyond or crossing the 2.1TiB limit. This required changes to signature of ext4fs_devread(), and type of all variables relatives to block sector. ext2/ext4 fs uses logical block represented by a 32 bit value. Logical block is a multiple of device block sector. To avoid overflow problem when calling ext4fs_devread(), we need to cast the sector parameter. Signed-off-by: Frédéric Leroy <fredo@starox.org>
2013-07-15Revert "MIPS: Jz4740: Add qi_lb60 board support"Tom Rini
The files board/qi/qi_lb60/qi_lb60.c and include/configs/qi_lb60.h were licensed under the GPL v3 or later, and not v2 or later. As this is incompatible with the project, revert this board support until the responsible parties are available to re-license (if so desired) under GPL v2. Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and serial. Conflicts: arch/arm/dts/exynos5250.dtsi Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12bootm: Use selected configuration for ramdisk and fdtSimon Glass
If a specific configuraion is selected by the bootm command, e.g. with 'bootm 84000000#recoveryconf' we must honour this for not just the kernel, but also the ramdisk and FDT. In the conversion to using a common fit_image_load() function for loading images from FITs (commits a51ec63 and 53f375f) this feature was lost. Reinstate it by passing the selected configuration back from fit_image_load() to boot_get_kernel(), then use this configuration (which is stored in images->fit_uname_cfg) in both boot_get_ramdisk() and boot_get_fdt(). Signed-off-by: Simon Glass <sjg@chromium.org>
2013-07-12Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-07-12mx53ard: Change default environment to cope with OE changesOtavio Salvador
OpenEmbedded has change partitioning layout of generated image so it does not raise warnings during the boot regarding unkown partition being used for U-Boot. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-17 01:00:40 +0000