| Age | Commit message (Collapse) | Author |
|---|
|
This function is defined in exports.c so move it to its header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These are filesystem functions and belong in the filesystem header file.
Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function belongs in the network header file. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These declarations are only used in fdtdec.c so move them to its header
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions are not used in U-Boot. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function belongs more in flash.h than common.h so move it.
Also remove the space before the bracket in some calls.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this function out of common.h and into a better place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
This is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Since CONFIG_LOADADDR is not set, the default value of $loadaddr
variable is not set in the environment either. Set the default
load address to 32 MiB from the start of DRAM (same value than
kernel_addr_r).
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This commit add to u-boot the support to decrypt
fit image encrypted with aes. The FIT image contains
the key name and the IV name. Then u-boot look for
the key and IV in his device tree and decrypt images
before moving to the next stage.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
This commit add the support of encrypting image with aes
in mkimage. To enable the ciphering, a node cipher with
a reference to a key and IV (Initialization Vector) must
be added to the its file. Then mkimage add the encrypted
image to the FIT and add the key and IV to the u-boot
device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Until now, we only support aes128. This commit add the support
of aes192 and aes256.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In the code, we use the size of the key for the
size of the block. It's true when the key is 128 bits,
but it become false for key of 192 bits and 256 bits.
So to prepare the support of aes192 and 256,
we introduce a constant for the iaes block size.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Not all systems have all the boot devices enabled, e.g. not all systems
have MTD devices and thus do not enable UBI. Make all the boot devices
in the distro bootcmd conditional to avoid failures.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
SoC base addresses should better go into a common SoC file instead
of repeating the definition in each board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
As we use the driver model for ESDHC there is no need
for defining CONFIG_SYS_FSL_USDHC_NUM and CONFIG_SYS_FSL_ESDHC_ADDR,
so simply remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
- Cleanup of fsl_esdhc driver together with arch/defconfig change
- Add quirk for APP_CMD retry
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2020.04
ARM64:
- Add INIT_SPL_RELATIVE dependency
SPL:
- FIT image fix
- Enable customization of bl2_plat_get_bl31_params()
Pytest:
- Add test for octal/hex conversions
Microblaze:
- Fix manual relocation for one SPI instance
Nand:
- Convert zynq/zynqmp drivers to DM
Xilinx:
- Enable boot script location via Kconfig
- Support OF_SEPARATE in board FDT selection
- Remove low level uart setup it is done later by code
- Add support for DEVICE_TREE variable passing for SPL
Zynq:
- Enable jtag boot mode via distro boot
- Removing unused baseaddresses from hardware.h
- DT fixups
ZynqMP:
- Fix emmc boot sequence
- Simplify spl logic around bss and board_init_r()
- Support psu_post_config_data() calling
- Tune mini-nand DTS
- Fix psu wiring for a2197 boards
- Add runtime MMC device boot order filling in spl
- Clear ATF handoff handling with custom bl2_plat_get_bl31_params()
- Add support u-boot.its generation
- Use single image configuration for all platforms
- Enable PANIC_HANG via Kconfig
- DT fixups
- Firmware fixes
- Add support for zcu208 and zcu1285
Versal:
- Fix emmc boot sequence
- Enable board_late_init() by default
|
|
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
|
|
This patch add clock driver for MediaTek MT7622 SoC.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
|
|
Sometimes we may need get (optional) clock without a device,
that means use ofnode.
e.g. when the phy node has subnode, and there is no device created
for subnode, in this case, we need these new APIs to get subnode's
clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
|
|
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
|
|
Add clock driver for MediaTek MT8512 SoC, include topckgen,
apmixedsys and infracfg support.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
|
|
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
|
|
The below patch added eSDHC periperhal clock code initially.
2d9ca2c mmc: fsl_esdhc: Add peripheral clock support
The purpose was to fix up device tree properties "peripheral-frequency"
so that linux could get the periperhal clock by it.
However the implementation on both u-boot and linux was only
for a Freescale SDK release. The linux part implementation had never
been upstreamed. These code should not have been exist on u-boot
mainline.
Let's remove the powerpc part changes but keep the changes in
fsl_esdhc driver. The changes in fsl_esdhc driver could be utilized
to support SD UHS and eMMC HS200/HS400 speed modes for current
Layerscape ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
asm-generic/sections.h references ulong but does not include
linux/types.h
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
Add stub for dma_memcpy() and dma_get_device when CONFIG_DMA is
disabled. This avoids ifdefs in driver code using DMA APIs
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This commit adds board support for i.MXRT1050-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT105x processor family.
More information about this board can be found here:
https://www.nxp.com/design/development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1050-evaluation-kit:MIMXRT1050-EVK
The initial supported/tested devices include:
- Debug serial
- SD
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Add SDRAM driver for i.MXRT SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Add i.MXRT compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08 as done
for i.MX8. It needs also to set baudrate the same way as i.MX8 does.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Add dtsi file for i.MXRT1050.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Add i.MXRT1050 clk driver support.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
|
|
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Add support for Capricorn Deneb SoM variant.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Add support for i.MX8X based Capricorn Giedi SoM.
Supported interfaces: GPIO, ENET, eMMC, I2C, UART.
Console output:
U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100)
Trying to boot from MMC1
Load image from MMC/SD 0x3e400
U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
Model: Siemens Giedi
Board: Capricorn
Boot: MMC0
DRAM: 1022 MiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
In: serial@5a080000
Out: serial@5a080000
Err: serial@5a080000
Net: eth1: ethernet@5b050000 [PRIME]
Autobooting in 1 seconds, press "<Esc><Esc>" to stop
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Convert another option Kconfig.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Follow i.MX, Sunxi, RISC-V and Rockchip to generate u-boot.itb which
includes U-Boot proper, ATF and DTBs in FIT format. ZynqMP supports FIT for
quite a long time but with using out of tree solution. The patch is filling
this gap.
Tested on zcu102, zcu104 and zcu100/Ultra96.
zcu100/Ultra96 v2.2 ATF build by:
make DEBUG=0 ZYNQMP_CONSOLE=cadence1 RESET_TO_BL31=1 PLAT=zynqmp bl31
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds new jtag distro boot command to look for bootscript
file in DDR and execute it first incase of jtag bootmode.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx ZynqMP platform is passing information to ATF in private format and
ATF bl31 parameters are not used. That's why enable option to rewrite this
function by platform specific implementation.
The patch also move and update kernel-doc format with missing parameters.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
|
|
Remove unneeded fec-related defines after fec moved as dm.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
|
|
- A small PR with MC8309 fixes from Rasmus.
|
|
dm: Increased separation of ofdata_to_platdata() and probe methods
|
|
- DFU updates
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
---------------------------------------------------------------------
Add i.MX8MP SoC and EVK board
Update README for i.MX8MN EVK and fix mmc env
Add pca9450 driver
--------------------------------------------------------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/634211885
|
|
|
