| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds check for command response CRC failure. The driver
is currently ignoring CRC check failure on command resposes which
have CRC atteched to it, which can be potentially dangerous. Even
more grueling problem happens when the command response is followed
by data transfer though, as in that case, the dwmci_data_transfer()
function will spin until it reaches the 240s timeout.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This reverts commit c0434407b595f785fc7401237896c48c791b45fd.
It turns out commit c0434407b595 broke some boards which have DM CPU
driver with CONFIG_DISPLAY_CPUINFO option on. These boards just fail
to boot when print_cpuinfo() is called during boot.
Fixes are already sent to ML and in u-boot-dm/next, however since
we are getting close to the v2018.11 release, it's safer we revert
the original commit.
This commit should be reverted after v2018.11 release.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Default setup is 0 which is incorrect place because it points to OCM
which is allocated for SPL only in our case.
Use address in DDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Just 2 non-functinal changes:
1. Rename of EMDK to EMSDP so it matches real marketing name
2. Add essential README for IoTDK
|
|
Real marketing name of the board was recently updated so
to accommodate that change renaming the board and all
related to it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
This part should've been remove in commit 88d60db01168 ("arm: ti: boot:
Remove environment partition"), but I missed it somehow. Remove reading
dtb file from environment partition on eMMC, as we don't have it
anymore.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
The default bootcommand needs to be accurate w.r.t the nand memory map
at http://www.at91.com/linux4sam/bin/view/Linux4SAM/AT91sam9x5ekMainPage#NAND_Flash_demo_Memory_map
Updated to load kernel + dtb at right offsets and boot the zImage.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
|
|
Commit 768f23dc8ae3 ("ARM: socfpga: Put stack at the end of SRAM") broke
those socfpga boards that keep the bootcounter at the end of the
internal SRAM as the bootcounter needs 8 bytes by default and thus the
very first SPL call to board_init_f_alloc_reserve overwrites the
bootcounter.
This patch allows to move the initial stack pointer down a bit by
checking if CONFIG_SYS_BOOTCOUNT_ADDR is located in the internal SRAM
area and then using this address as location for the start of the
stack pointer.
No new macros / defines are added by this approach.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Workaround makes FS as default mode on all affected socs.
Add support to check erratum-A005275 validity for an soc. This info is
required to determine whether a given soc is affected by this erratum.
Add quirk for this erratum "has_fsl_erratum_a005275" . This quirk is used
to enable workaround for the errata
Force FS mode as default by:
- making EPS as FS
- setting PFSC bit to disable HS chirping
This workaround can be disabled by mentioning "no_erratum_a005275" in
hwconfig string
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
To enable the root device selection (kernel cmd-line) via PARTUUID, this
patch enables CMD_PART on all missing theadorable-x86 boards and
changes the default environment to generate the root=PARTUUID string
automatically.
This fixes problems that have been noticed on systems with multiple
SATA/AHCI controller connected via PCIe, where the device name for the
root device / partition (/dev/sdaX) was incorrect.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This is needed for the PCIe hotplug to work correctly on some boards
with the newer Linux kernel versions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
Merged imx8 architecture, fix build for imx8 + warnings
|
|
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In upcoming freescale board LX2160AQDS, the MDIO bus is muxed.
i.e. same MDIO bus can be routed to eight different slots depending
on mux register settings.
To support this mdio mux behavior, we add each MDIO bus mux as a
separate MDIO bus.
Now, various phy devices can be attached to each of these slots(mux).
The information about these devices is passed to OS via device tree.
To do the fdt fixups related to MDIO bus, its necessary that MDIO bus
list is accessed.Therefore, add a function to retrieve the list head.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1.
The linux kernel does not provide a hc2 DTB so the hc1 DTB is also used
for the Odroid HC2.
Resend because MUA changed whitespace.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Remove "environment" partition and do not read it when booting Android
from eMMC. We don't use this partition anymore, so this is just an
unintentional leftover.
Earlier we were reading dtb file from "environment" partition to feed it
further to kernel. Now we are using dtb from FIT image ("boot" partition
contains boot_fit.img image), which can be seen from this command:
bootm ${loadaddr}#${fdtfile}
where "#" character means we have FIT image in ${loadaddr} RAM address.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
|
|
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
If we have defined the OPTEE ram size and not OPTEE means that we are in
the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and
that most of the low level initialization is already done and that we
may/should skip it doing them here.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: u-boot@lists.denx.de
|
|
Move this option to Kconfig and tidy up the config file of eight
boards which use it.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
|
|
i.MX8/8X bootable image type is container type.
The bootable image, containers a container set which supports two
container. The 1st container is for SECO firmware, the 2nd container
needs to include scfw, m4_0/1 image, ACore images per your requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8QXP MEK board support
Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver.
Added README file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Add i.MX8 compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also, according to RM, the Receive FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08
(not 0x40) for i.MX8, otherwise the Receive FIFO is not disabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX8QXP power and resource definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX8QXP clocks definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add i.MX8QXP pads definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
%s/CMD_RET_SUCCESX/CMD_RET_SUCCESS/g
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add new Kconfig option, SYS_BOOTCOUNT_MAGIC, to select the boot
counter magic word. This can be useful ie. in case the entire
boot counter register is not usable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
The option is unused, SPL image gets a wanted boot device by standard
spl_boot_device() call.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The CONFIG_LPC32XX_SPL option from board include file has never been
used, it is safe to remove it.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Add device tree nodes for USB2.0(EHCI) on R-Car E3 Ebisu board.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
|
|
This patch enables the cache command, mostly for convenience of testing.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
|
|
Patch queue for efi - 2018-10-17
A few bug fixes for the 2018.11 release:
- Fix block seeking on 32bit
- Fix execution with DEBUG set
- Fix a few Coverity found bugs
- Fix warnings
Heinrich Schuchardt (13):
efi_loader: fix relocation on x86_64
efi_loader: correct signature of GetPosition, SetPosition
efi_loader: execute efi_save_gd() first
efi_loader: efi_allocate_pool(EFI_ALLOCATE_ANY_PAGES, ...)
efi_loader: error handling in read_console()
efi_loader: return type efi_console_register()
efi_loader: superfluous statement in is_dir()
efi_loader: memory leak in efi_set_variable()
efi_loader: remove lcd.h from efi_net.c
arm: do not include efi_loader.h twice
efi_loader: fix typo in efi_boottime.c
efi_selftest: creating new handle in controller test
efi_loader: efi_dp_get_next_instance() superfluous statement
Tom Rini (2):
efi_loader: Fix warning in efi_load_image()
fs: fat: Fix warning in normalize_longname()
|
|
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use a return type that can encompass the return value.
This fixes CoverityScan CID 184090.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The UEFI spec requires that file positions are passed as u64 in
GetPosition() and SetPosition().
Check if the file handle points to a directory in GetPosition().
Provide a unit test for GetPosition() and SetPosition().
Fix Coverity warning CID 184079 (CONSTANT_EXPRESSION_RESULT).
Add comments.
Fixes: b6dd57773719 ("efi_loader: use correct types in EFI_FILE_PROTOCOL")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add Menlosystems M53 board, based on the M53 SoM.
This board has Ethernet, USB host, USB gadget, UART and LCD on it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
|
|
|
|
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.
i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The phydev structure is present in both ldpaa_eth_priv and
wriop_dpmac_info. the phydev in wriop_dpmac_info is not being used
As the phydev is created based on phy_addr and bus members of
wriop_dpmac_info, it is appropriate to keep phydev in wriop_dpmac_info.
Also phy_regs is not being used, therefore remove it
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
|
|
This adds platform code for the Khadas VIM2 board based on a
Meson GXM (S912) SoC with the Meson GXM configuration.
This initial submission supports UART, MMC/SDCard and Ethernet.
USB is partially supported.
All the code is from Neil Armstrong! I just rebased the code, do
some cleanup and tested on my board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Make it possible to add TCP versions of the same, while reusing
IP portions. This patch should not change any behavior.
Signed-off-by: Duncan Hare <DH@Synoia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Peter originally sent a fix, but it breaks a number of other things.
This addresses the original reported issue in a different way.
That report was:
> U-Boot has 1 common buffer to send Ethernet frames, pointed to by
> net_tx_packet. When sending to an IP address without knowing the MAC
> address, U-Boot makes an ARP request (using the arp_tx_packet buffer)
> to find out the MAC address of the IP addressr. When a matching ARP
> reply is received, U-Boot continues sending the frame stored in the
> net_tx_packet buffer.
>
> However, in the mean time, if U-Boot needs to send out any network
> packets (e.g. replying ping packets or ARP requests for its own IP
> address etc.), it will use the net_tx_packet buffer to prepare the
> new packet. Thus this buffer is no longer the original packet meant
> to be transmitted after the ARP reply. The original packet will be
> lost.
This instead uses the ARP tx buffer to send async replies in the case
where we are actively waiting for an ARP reply.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Tran Tien Dat <peter.trantiendat@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This single-sources the state of the ARP.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
