| Age | Commit message (Collapse) | Author |
|---|
|
The HCD may have limitation on the maximum bytes to be transferred
in a USB transfer. USB class driver needs to be aware of this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
|
|
The status register is optional in the AMD command sets, but it's
presence can be checked by reading out CFI table entry 0xc bit 0.
If the register is present, prefer using it's bit 7 to determine
if the flash is busy over reading the flash ; this is needed ie.
on Hyperflash memories.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Embed the flash base into struct flash_info instead of having ad-hoc
static array in the code. This does not only remove static variable,
but also allows CFI-like controllers, ie. HyperFlash ones, to use most
of the CFI flash code by populating the flash_info with matching base
address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Current u-boot disables IFC support for SD boot on all ls1043a
boards. Actually IFC only conflicts with QSPI on ls1043a hardware.
Only when QSPI is used, IFC should be disabled. Otherwise,
the u-boot with ls1043aqds_sdcard_ifc_defconfig would not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
For most of ls2080ardb use-cases, mc private DRAM block is required
to be of 1.75GB.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: this reservation needs to be reduced if memory is not enough]
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
CONFIG_DISPLAY_BOARDINFO_LATE config is used to delay
the prints of boardinfo late in cycle during uboot boot.
This feature is not required in case of QSPI_BOOT.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Commit a8ecb39e accidentally reverted config macro CONFIG_ARCH_LS1021A
to CONFIG_LS102XA.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
dev_read_string_count() is used to get the number of strings in a
stringlist.
dev_read_string_index() is used to get a string in the stringlist based on
its position in the list.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This driver is adapted from linux drivers/reset/reset-stm32.c
It's compatible with STM32 F4/F7/H7 SoCs.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
To add support for each SoC family, a SoC's specific
include/dt-binfings/mfd/stm32xx-rcc.h file must be added.
This patch only includes stm32h7-rcc.h dedicated for STM32H7 SoCs.
Other SoCs support will be added in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable USB Host Networking support by enabling Ethernet/USB
adaptors support and by enabling some BOOTP flags
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add spi dts node and enable spi dm flash config.
Signed-off-by: rick <rick@andestech.com>
|
|
Enable cache and ftmac100 performance can be improved.
Signed-off-by: rick <rick@andestech.com>
|
|
|
|
Define i2c mux configuration. Add new vpd_reader which is used to read
vital product data. Read VPD from EEPROM and set eth0 MAC address.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Jose Alarcon <jose.alarcon@ge.com>
|
|
The hummingboard2 is slightly different to the cubox i and to the
hummingboard. The GPIO pin info to probe came from solidruns
for of u-boot on github.
https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589
I have tested on a hummingboard-edge witha imx6 solo and 512mb of
ram.
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
|
|
1) use fputs() to reduce cache flushes from once-per-char to
once-per-string
2) handle \r, \t, and \b in addition to just \n for tracking
cursor position
3) cursor row/col are zero based, not one based
Signed-off-by: Rob Clark <robdclark@gmail.com>
[agraf: s/unsigned/unsigned int/]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
These should be set according to the image type. Shell.efi and SCT.efi
use these fields to determine what sort of image they are loading.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Similar to a "real" UEFI implementation, the bootmgr looks at the
BootOrder and BootXXXX variables to try to find an EFI payload to load
and boot. This is added as a sub-command of bootefi.
The idea is that the distro bootcmd would first try loading a payload
via the bootmgr, and then if that fails (ie. first boot or corrupted
EFI variables) it would fallback to loading bootaa64.efi. (Which
would then load fallback.efi which would look for \EFI\*\boot.csv and
populate BootOrder and BootXXXX based on what it found.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add EFI variable support, mapping to u-boot environment variables.
Variables are pretty important for setting up boot order, among other
things. If the board supports saveenv, then it will be called in
ExitBootServices() to persist variables set by the efi payload. (For
example, fallback.efi configuring BootOrder and BootXXXX load-option
variables.)
Variables are *not* currently exposed at runtime, post ExitBootServices.
On boards without a dedicated device for storage, which the loaded OS
is not trying to also use, this is rather tricky. One idea, at least
for boards that can persist RAM across reboot, is to keep a "journal"
of modified variables in RAM, and then turn halt into a reboot into
u-boot, plus store variables, plus halt. Whatever the solution, it
likely involves some per-board support.
Mapping between EFI variables and u-boot variables:
efi_$guid_$varname = {attributes}(type)value
For example:
efi_8be4df61-93ca-11d2-aa0d-00e098032b8c_OsIndicationsSupported=
"{ro,boot,run}(blob)0000000000000000"
efi_8be4df61-93ca-11d2-aa0d-00e098032b8c_BootOrder=
"(blob)00010000"
The attributes are a comma separated list of these possible
attributes:
+ ro - read-only
+ boot - boot-services access
+ run - runtime access
NOTE: with current implementation, no variables are available after
ExitBootServices, and all are persisted (if possible).
If not specified, the attributes default to "{boot}".
The required type is one of:
+ utf8 - raw utf8 string
+ blob - arbitrary length hex string
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
fallback.efi (and probably other things) use UEFI's simple-file-system
protocol and file support to search for OS's to boot.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[agraf: whitespace fixes, unsigned fixes]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Get rid of the hacky fake boot-device and duplicate device-path
constructing (which needs to match what efi_disk and efi_net do).
Instead convert over to use efi_device_path helpers to construct
device-paths, and use that to look up the actual boot device.
Also, extract out a helper to plug things in properly to the
loaded_image. In a following patch we'll want to re-use this in
efi_load_image() to handle the case of loading an image from a
file_path.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
It needs to handle more device-path node types, and also multiple levels
of path hierarchy. To simplify this, initially construct utf8 string to
a temporary buffer, and then allocate the real utf16 buffer that is
returned. This should be mostly for debugging or at least not critical-
path so an extra copy won't hurt, and is saner than the alternative.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This is really the same thing as the efi_device_path struct.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Helpers to construct device-paths from devices, partitions, files, and
for parsing and manipulating device-paths.
For non-legacy devices, this will use u-boot's device-model to construct
device-paths which include bus hierarchy to construct device-paths. For
legacy devices we still fake it, but slightly more convincingly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
All of the device-path related structures should be packed. UEFI
defines the device-path as a byte-aligned data structure.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
EFI client programs need the signature information from the partition
table to determine the disk a partition is on, so we need to fill that
in here.
Signed-off-by: Peter Jones <pjones@redhat.com>
[separated from efi_loader part, and fixed build-errors for non-
CONFIG_EFI_PARTITION case]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Prep work for next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
For the correct implementation of the task priority level (TPL)
calling the notification function must be queued.
Add a status field 'queued' to events.
In function efi_signal_event set status queued if a notification
function exists and reset it after we have called the function.
A later patch will add a check of the TPL here.
In efi_create_event and efi_close_event unset the queued status.
In function efi_wait_for_event and efi_check_event
queue the notification function.
In efi_timer_check call the efi_notify_event
if the status queued is set.
For all timer events set status signaled.
In efi_console_timer_notify set the signaled state of the
WaitForKey event.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
A testing framework for the EFI API is provided.
It can be executed with the 'bootefi selftest' command.
It is coded in a way that at a later stage we may turn it
into a standalone EFI application. The current build system
does not allow this yet.
All tests use a driver model and are run in three phases:
setup, execute, teardown.
A test may be setup and executed at boottime,
it may be setup at boottime and executed at runtime,
or it may be setup and executed at runtime.
After executing all tests the system is reset.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Macro EFI_CALL was introduced to call an UEFI function.
Unfortunately it does not support return values.
Most UEFI functions have a return value.
So let's rename EFI_CALL to EFI_CALL_VOID and introduce a
new EFI_CALL macro that supports return values.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Fix typo in teh EFI_BOOT_SERVICES_CODE description.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
In scripts/Makefile.lib we build section including helloworld.efi.
This allows to load the EFI binary with command 'bootefi hello'.
scripts/Makefile.lib contains explicit references to strings
containing helloworld and hello_world. This makes it impossible
to generalize the coding to accomodate additional built in
EFI binaries.
Let us rename the variables __efi_hello_world_* to
__efi_helloworld_*.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
To understand what is happening in OpenProtocol or LocateProtocol
it is necessary to know the protocol interface GUID.
Let's write a debug message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add the ENV_MEM_LAYOUT_SETTINGS to CONFIG_EXTRA_ENV_SETTINGS
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The dev_read_addr_ptr() mimics the behaviour of the devfdt_get_addr_ptr(),
retrieving the first address of the node's reg-property and returning
it as a pointer (or NULL on failure).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
