| Age | Commit message (Collapse) | Author |
|---|
|
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
|
|
Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:
fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
.write = ext4_write_file,
^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: Chris Spencer <spencercw@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Change CONFIG_ENV_OFFSET for Poplar to be 1MB further into the eMMC
than before. This puts it immediately prior to the space we are
reserving offset 0x200000-0x400000 for UEFI to save its persistent
data. Define CONFIG_ENV_SIZE as a product of env_mmc_nblks and the
sector size, like CONFIG_ENV_OFFSET is.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Fixes for 2019.01
|
|
Check the size of the generated u-boot.imx file. Report an error
if it would be too big and overwrite the u-boot environment.
Signed-off-by: Soeren Moch <smoch@web.de>
|
|
Enable watchdog and bootcounter support on the M53Menlo board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Remove unused Android partitions:
- efs, crypto, cache: we don't use it anymore (images are not built
in AOSP
- ipu1, ipu2: IPU firmware is now a part of vendor image and doesn't
reside as a separate partition
While at it, rename "reserved" partition to "uboot-env", as it's
actually stores U-Boot environment.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
|
|
|
|
pinctrl_decode_pin_config_dm() is basically a feature-equivalent
implementation of pinctrl_decode_pin_config(), which operates
on struct udevice devices and uses the dev_read_*() API.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
imx for 2019.01
- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x
|
|
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" causes U-Boot to hang because of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Currently, U-Boot ignores the BBT stored in the last 4 blocks of NAND
flash because the NAND_BBT_USE_FLASH flag is not set. This leads to
two issues:
* U-Boot silently uses a memory-only BBT which is initialized with all
blocks marked as good. This means, actual bad blocks are marked good
and U-Boot might try writing to or reading from them.
* The BBT in flash, which will be created once Linux boots up, is not
off limits for a driver ontop, like UBI. While it does not seem to
consistently produce an error, sometimes UBI will fail to attach
because the BBT blocks obviously don't contain valid UBI data.
To fix this, this patch sets the CONFIG_SYS_NAND_USE_FLASH_BBT option,
which is used in ./drivers/mtd/nand/raw/mxs_nand.c to decide whether
a BBT in flash is used.
Signed-off-by: Harald Seiler <hws@denx.de>
|
|
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.
The boot log with Arm trusted firmware console enabled:
"
U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
PMIC: PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
NOTICE: Configureing TZASC380
NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty
NOTICE: BL31: Built : 09:28:54, Nov 8 2018
lpddr4 swffc start
NOTICE: sip svc init
U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM: 3 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
i.MX8M bootable image type is like i.MX6/7, but there is signed HDMI
firmware image in front of A53 bootable image, which is also has an IVT
header.
Here we also include fit image to generate a bootable image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Introduce function prototypes for board_spl_fit_size_align and
board_spl_fit_post_load
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
In order to boot faster with falcon mode, we need to add SPL
support to riotboard.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
|
|
For future extension to other architectures, make do_bootm_vxworks()
a non-static function.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Change the scope of do_bootvx_fdt() to static since it is only
used in common/bootm_os.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This includes x86 edison defconfig file clean up, and coreboot file
system (cbfs) fixes.
|
|
Current CBFS component type list is incomplete. Add missing ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present there are 2 macros that are named as CBFS_COMPONENT_xxx.
Change them to CBFS_TYPE_xxx for consistency.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Since some options had been moved to defconfig from header,
the leftover comments are not needed anymore. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use defconfig instead of header file for CONFIG_BOOTCOMMAND.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use defconfig instead of header file for CONFIG_CMD_PCI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Copied from Linux v4.20-rc7.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
For more boot-flow flexibility,
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Some users might need additional setups before booting the kernel.
If there is found a file 'boot.scr', run it before invoking the
distro boot command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fix typo: neede -> needed
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
boards. At one point, the #ifdef's were replaced with
if CONFIG_IS_ENABLED but this won't work for people who need
OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
used in Kconfig. This patch moves the check to #if defined and
also makes Kconfig select the banks if CMD_GPIO is used which
makes the checks in the code less cumbersome.
Fixes: bd8a9c14c91c ("arm: mach-omap2/omap3/clock.c: Enable
all GPIO with CMD_GPIO")
Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate omap3_igep00x0.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This reverts commit 232ed3ca534708527a9515c7c41bc3542949525c.
In exynos boards, ${console} is used to set bootargs but it sets
without "console=", so CONFIG_DEFAULT_CONSOLE for these boards is
designated with "console=" but it is removed. So revert the commit.
References for using ${console} in
board/samsung/common/bootscripts/autoboot.cmd
board/samsung/common/bootscripts/bootzimg.cmd
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
- Fix breakage in helios4: Change U-Boot offset on SPI Flash
- Enable CONFIG_BLK for db-88f6820-amc
|
|
- stratix10 updates
|
|
- mips: fix some DTC warnings
- bmips: bcm6348: add DMA driver
- bmips: bcm5348: add ethernet driver
- bmips: bcm6368: add ethernet driver
- mips: mt76xx: fix DMA problems, disable CONFIG_OF_EMBED
- mips: mscc: add support for Microsemi Ocelot and Luton SoCs
- mips: mscc: add support for Ocelot and Luton evaluation boards
- mips: jz47xx: add basic support for Ingenic JZ4780 SoC
- mips: jz47xx: add support for Imgtec Creator CI20 board
|
|
SPI flash support on Helios4 [1] has been merge to u-boot/master on
commit 8cb8c0c6a83bef ("Merge git://git.denx.de/u-boot-marvell")
However, the SPI image build failed after the merge with following
message:
COPY spl/u-boot-spl.bin
MKIMAGE u-boot-spl.kwb
Error: Image header (incl. SPL image) too big!
header=0x20816 CONFIG_SYS_U_BOOT_OFFS=0x20000!
Increase CONFIG_SYS_U_BOOT_OFFS!
Error: Image header (incl. SPL image) too big!
header=0x20816 CONFIG_SYS_U_BOOT_OFFS=0x20000!
Increase CONFIG_SYS_U_BOOT_OFFS!
Could not create image
Makefile:1162: recipe for target 'u-boot-spl.kwb' failed
make: *** [u-boot-spl.kwb] Error 1
Let's increase the u-boot offset to 0x30000 to accommodate SPL changes
and leave some margin for future changes.
[1] https://patchwork.ozlabs.org/patch/1007762/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add missing exynos5422-odroidhc1.dtb needed to set for dfu env.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
|
|
Enable FPGA reconfiguration support for Stratix 10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
|
|
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Add initial support for the Ingenic JZ47xx MIPS SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Adding the support for 2 boards sharing common code for Ocelot chip:
PCB120 and PCB123
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
