| Age | Commit message (Collapse) | Author |
|---|
|
Since commit commit 152038ea1886 ("i.MX6UL: icore: Add SPL_OF_CONTROL
support") the OPOS6UL board doesn't boot anymore. Adding SPL_DM support
makes the board boot again.
Fixes: commit 152038ea1886 ("i.MX6UL: icore: Add SPL_OF_CONTROL support")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
|
|
This patch adds support for verifying a signed boot.scr. With this in place
it's possible for run-time Linux to update boot.scr to set different
variables such as switching between different boot partitions, pointing to
different kernels etc and for u-boot to verify these changes via the HAB
prior to executing the commands contained in boot.scr.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This patch introduces the environment variable ivt_offset. When we define a
load address for Linux or DTB or any file the IVT associated with that file
is prepended. We extract the actual load addresses from u-boot.cfg and feed
these values into the code-signing process - hence we want u-boot to have
the real load addresses exported in uboot.cfg.
ivt_offset represents the addition or subtraction from the load address
that must happen to find an IVT header.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Doing secure boot on the WaRP7 using a common image format and the same
variable to represent the base address for each call means we can reduce
down the command to a single environment command.
This patch adds warp7_auth_or_fail as a wrapper around
"hab_auth_img_or_fail ${hab_ivt_addr} ${filesize} 0".
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
We need to know the name of a signed boot-script, its better to have a
separate variable for this then to simply append some fixed string to an
existing image name.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Assigning the UUID discovery path to a tweakable environment variable means
that later steps in the boot process - particularly a boot script can
change the target root partition of a particular Linux boot.
Retargeting the rootfs is an important feature when doing ping/pong
upgrades allowing a boot script to select ping or pong as necessary without
reprogramming the bootloader.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
In order to sign images with the IMX code-signing-tool (CST) we need to
know the load address of a given image. The best way to derive this load
address is to make it into a define - so that u-boot.cfg contains the
address - which we can then parse when generating the IMX CST headers.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
In order to sign images with the IMX code-signing-tool (CST) we need to
know the load address of a given image. The best way to derive this load
address is to make it into a define - so that u-boot.cfg contains the
address - which we can then parse when generating the IMX CST headers.
This patch makes the OPTEE_LOAD_ADDR available via u-boot.cfg for further
parsing by external tools.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This patch adds an environment variable called "hab_enabled" which gets set
to a boolean status indicating whether HAB is enabled or not.
Subsequent patches can use this environment variable to determine if its
necessary to run a given binary through the hab_auth_img console command.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This patch adds BOOTROM_IVT_HDR_OFFSET at 0xC00. The BootROM expects to
find the IVT header at a particular offset in an i.MX image.
Defining the expected offset of the IVT header in the first-stage BootROM
image format is of use of later stage authentication routines where those
routines continue to follow the first-stage authentication layout.
This patch defines the first stage offset which later patch make use of.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
use the generic filesystem command 'load' rather
than 'fatload' to avoid per-fs specific commands.
Signed-off-by: Pierre-Jean TEXIER <texier.pj2@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
|
|
|
|
Patch queue for efi - 2018-04-23
Some last minute fixes for 2018.05. Most of them are minor fixes. On
top we have some functional improvements for the device path logic
which should also help us be more compatible.
|
|
The missing services of the EFI_DEVICE_PATH_UTILITIES_PROTOCOL are
implemented.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Device paths may consist of multiple instances. Up to now we have only
considered the size of the first instance. For the services of the
EFI_DEVICE_PATH_UTILITIES_PROTOCOL in most cases the total length of the
device path is relevant.
So let's rename efi_dp_size() to efi_dp_instance_size() and create a new
function efi_dp_size() that calculates the total device path length.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Implement the CreateDeviceNode service of the device path utility protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Executing a test after failed setup may lead to unexpected behavior like
an illegal memory access. So after a setup failure we should skip to
teardown.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
According to the documentation the EFI log category is called LOGC_EFI.
All other categories start with LOGC_. So let's fix it.
Fixes: 1973b381a1b3 ("log: add category LOGC_EFI")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
|
|
Currently, the address region, 0xf8000 - 0x100000, is used for SPL
stack for the 32bit SoCs. Because the U-Boot proper image starts
from 0x70000, the maximum size of the U-Boot proper image is 544KB
(0x70000 - 0xf8000) for the NOR boot mode. Now uniphier_v7_defconfig
is almost hitting this size limit. Changing CONFIG_SPL_STACK can
raise the size limit with less impact. With this, the size limit
will increase to 576KB (0x70000 - 0x100000). If we need to increase
it even more, we would be able to change CONFIG_SYS_UBOOT_BASE at the
cost of the flashing command changes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Some boards support an SD card and an eMMC device at the same time.
Since both belong to 'mmc', they are identified by a device number.
When the device number of the eMMC is 1 instead 0, "mmc dev" command
must be performed to switch the target device before flashing images.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
With the recent changes, the size of the U-Boot proper image for
uniphier_v7_defconfig exceeded the current limit, 512KB, then SPL
fails to load the whole of the U-Boot proper. Increase the size.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Boards have an option to rewrite variable locations in their own board
files. This is necessary for qspi and nand configurations where boot
image can be bigger then 896k(current limit).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The E2 Silk port was broken since some time. This patch updates
the E2 Silk port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The port is missing support for I2C1 for DA9063 reset, since the
I2C driver needs to be converted to DM and DT probing. That's not
an issue for this patch though, since the reset was broken on Silk
since forever.
|
|
Migrate the U-Boot configs to Kconfig CONFIG_SH_MMCIF .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
|
|
|
|
In the commit "reset: Add get/assert/deassert/release for bulk of reset signals"
the disabled reset_release_bulk() and reset_get_bulk() used the wrong
struct clk_bulk instead of struct reset_ctl_bulk.
Fixes: 0c28233903b5 ("reset: Add get/assert/deassert/release for bulk of reset signals")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The M2 Koelsch port was broken since some time. This patch updates
the M2 Koelsch port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Enable DM I2C driver on SoCFPGA platforms.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Pulled from linux v4.16-rc4.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable the RPC QSPI driver on R8A77970 V3M Eagle and configure
the environment layout to match that used by old U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Relocate env drivers if manual relocation is enabled. This
patch fixes the issue of u-boot hang incase if env is
present in any of the flash devices.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
On VxWorks x86 its bootline address is at a pre-defined offset @
0x1200. If 'bootaddr' is not passed via environment variable, we
assign its value based on the kernel memory base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When booting from EFI BIOS, VxWorks bootloader stores the EFI GOP
framebuffer info at a pre-defined offset @ 0x6100. When VxWorks
kernel boots up, its EFI console driver tries to find such a block
and if the signature matches, the framebuffer information will be
used to initialize the driver.
However it is not necessary to prepare an EFI environment for
VxWorks's EFI console driver to function (eg: EFI loader in
U-Boot). If U-Boot has already initialized the graphics card and
set it to a VESA mode that is compatible with EFI GOP, we can
simply prepare such a block for VxWorks.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds ELF header, program header and section header structure
defines for the 64-bit ELF image.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Fix various style violations in elf.h
- use correct comment format if the comment fits in just one line
- remove the ending period for the one-line comment
- use tab for the indention instead of space
- put the opening brace at the same line of a typedef/union
- remove <name> in a 'typedef struct' for consistency
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
This changes 'struct e820info' to 'struct e820_info' to conform
with the coding style.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
VxWorks bootloader stores its size at a pre-defined offset @ 0x5004.
Later when VxWorks kernel boots up and system memory information is
retrieved from the E820 table, the bootloader size will be subtracted
from the total system memory size to calculate the size of available
memory for the OS.
Explicitly clear the bootloader image size otherwise if memory
at this offset happens to contain some garbage data, the final
available memory size for the kernel is insane.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
address
At present two environment variables 'e820data'/'e820info' are required
to boot a VxWorks x86 kernel, but this is superfluous. The offset of
these two tables are actually at a fixed offset from the kernel memory
base address and we can provide the kernel memory base address to U-Boot
via only one variable 'vx_phys_mem_base'.
Note as it name indicates, the physical address should be provided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
This platform has been marked as orphaned since September 2013, remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This platform has been marked as orphaned since September 2013, remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Replace fatload with the fs generic loading interface ('load' command).
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This commit provides support for Kieback & Peter GmbH IMX6Q based
TPC board.
U-boot console output:
U-Boot SPL 2018.05-rc1-00005-g631e2d01fd (Apr 04 2018 - 21:16:24 +0200)
Trying to boot from MMC1
U-Boot 2018.05-rc1-00005-g631e2d01fd (Apr 04 2018 - 21:16:24 +0200)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 37C
Reset cause: POR
Board: K+P KP_IMX6Q_TPC i.MX6Q
Watchdog enabled
I2C: ready
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Autoboot in 3 seconds
|
|
Enable display backlight only if a message needs to be displayed.
The kernel re-initializes the backlight, which results in some
unwanted artifacts.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Subsequent patches will want to include imageimage.h but in doing so
include it on an assembly compile path causing a range of compile errors.
Fix the errors pre-emptively by encasing the majority of the declarations
in imximage.h inside an ifdef __ASSEMBLY__ block.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
|
|
u-boot has a standard "serial#" environment variable that is suitable
for storing the iSerial number we will supply via the USB device
descriptor. serial# is automatically picked up by the disk subsystem in
u-boot - thus providing a handy unique identifier in /dev/disk/by-id as
detailed below.
Storing the hardware serial identifier in serial# means we can change the
serial# if we want before USB enumeration - thus making iSerial automatic
via OTP but overridable if necessary.
This patch reads the defined OTP fuse and sets environment variable
"serial#" to the value read.
With this patch in place the USB mass storage device will appear in
/dev/disk/by-id with a unique name based on the OTP value. For example
/dev/disk/by-id/usb-Linux_UMS_disk_0_WaRP7-0xf42400d3000001d4-0:0
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
There is currently no use for building the SPL anymore, since the
SPI loader can easily be replaced by TPL and TPL does load U-Boot
directly. Upgrade TPL to SPL and replace what used to be SPL with
it. This way we build the U-Boot sources only twice, not thrice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
