| Age | Commit message (Collapse) | Author |
|---|
|
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
|
|
- add GPIO module description
- add Address Latch Timing Register description
- add IO Control Memory Map
- add FEC Memory Map
Also change board/freescale/mpc5121ads/mpc5121ads.c and
cpu/mpc512x/iopin.c as needed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
|
|
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
|
|
In case of incorrect command invocations U-Boot used to print pretty
useless "usage" messages, for example:
=> nand markbad
Usage:
nand - NAND sub-system
In the result, the user would have to run the "help" command to get
the (available) information about correct command usage. Change this,
so that this information gets always printed.
Note that this changes the user interface of all commands, but
hopefully to the better.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The kernel stores address<->symbol names in it so things can be decoded at
runtime. Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
By changing the cmd_mtdparts to only use the MTD infrastructure and
not the direct interface to the CFI NOR FLASH driver we now need
to add the MTD infrastructure to all boards using those mtdparts
commands. This patch adds those components:
CONFIG_MTD_DEVICE (for all FLASH types)
plus
CONFIG_FLASH_CFI_MTD (for NOR FLASH)
To all board maintainers: Please test this on your platforms and
report any problems/issues found. Thanks.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Martin Krause <martin.krause@tqs.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
|
|
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
|
|
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Enable the function and interface clocks for banks 2,3,5 and 6.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
This patch assigns the u-boot system timer interrupt to
interrupt level 3, priority 6. Without this patch the interrupt
will be a level 0, priority 0, which disables it and cause
u-boot functions that relies on the timer (e.g. sleep command)
to never return.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
This patch is required for Kirkwood support
may be used by other ARM architectures
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
With other OMAP3 boards we recently switched to CPU and Board
info API. From parallel merge, this is missing for Zoom2.
Enable it for Zoom2, too.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
|
|
This patch controls the large LED on the top left of the zoom2.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
all arm init the IRQ stack the same way
so unify it in lib_arm/interrupts.c and then call arch specific interrupt init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Also enable display of 'E'mpty sectors in "flinfo" output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Also reserve more space for U-Boot as it will probably grow soon.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
The current configuration doesn't define default
bootfile; leading to this warning at execution:
OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img'
TFTP from server 0.0.0.0; our IP address is 192.168.1.11;
sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)
Signed-off-by: Sanjeev Premi <premi@ti.com>
|
|
Patch adds base addresses for DaVinci DM365. Updated patches for DM365
will be posted soon.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot.
The orignal source is in linux/arch/arm/plat-omap/gpio.c
See doc/README.omap3 for instructions on use.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
Zoom2 is a new board from Texas Instruments and LogicPD
The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com
This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp
This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.
To configure, run
make omap3_zoom2_config
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
update against linux v2.6.29
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This updates the optional (non-default!) NAND support for the
DaVinci DM6446 EVM:
- include MTD partitioning, defaulting to what Linux uses
- use a flash-based BBT, which among other things speeds bootup
This matches code that's now queued for mainline Linux, and might
even merge in an upcoming 2.6.30-rc; and the MTIDS are set up so
that the U-Boot $mtdparts environment variable can be passed as-is
on the kernel command line as a cmdlinepart override.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).
Switch boards to use the cpuinfo() hook for this stuff.
Remove a few now-obsolete PLL #defines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
These legacy NAND defines are no longer needed by this target.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
There is exiting support for red,yellow,green but no blue.
The main LED on the zoom2 is a blue LED.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
|
|
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow
so now rename it as int timer_init(void) and use interrupt_init for interrupt
btw also remane the corresponding file to the functionnality implemented
as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Add some basic declarations for DaVinci DM355/DM350/DM335 support,
keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the
DM357 is very different; while the DM355 is like a DM355 without
the MPEG/JPEG coprocessor).
These have different peripherals than the DM6446, and some of
the peripherals are at different addresses. Notably for U-Boot,
there's no EMAC, and the NAND controller address is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Split out DaVinci DM6446-specific bits from more generic bits:
- Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips;
DM6443 and DM6441 chips differ in available peripherals.
- Move most DM644X-specific bits from psc.c to a new dm644x.c file,
which is conditionally built. It provides device-specific setup.
Plus minor coding style and comment updates with respect to the PSC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Move DaVinci PSC support from board/* to cpu/* where it belongs.
The PSC module manages clocks and resets for all DaVinci-family
SoCs, and isn't at all board-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").
Here the commands to load and start this image from the BDI2000:
440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000
Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
All in-tree PPC4xx boards now use CONFIG_NET_MULTI
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes the cpld binary bitstream that is
used by esd's cpld command on DP405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes the cpld binary bitstream that is
used by esd's cpld command on VOM405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes the cpld binary bitstream that is
used by esd's cpld command on PMC405 boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes the cpld binary bitstream that is
used by esd's cpld command on CMS700 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Add standard CONFIG_SYS_I2C_SPEED define for the mpc7448hpc2 so that
it can use the common 'i2c speed' command. Note that the I2C controller
utilized by the mpc7448hpc2 has a fixed speed and cannot be changed
dynamically.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Many boards/controllers/drivers don't support an I2C slave interface,
however CONFIG_SYS_I2C_SLAVE is used in common code so provide a
default
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
