| Age | Commit message (Collapse) | Author |
|---|
|
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
|
|
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
In some boards like the Raspberry Pi the initial bootloader will pass
a DT to the kernel. When using U-Boot as such kernel, the board code in
U-Boot should be able to provide U-Boot with this, already assembled
device tree blob.
This patch introduces a new config option CONFIG_OF_BOARD to use instead
of CONFIG_OF_EMBED or CONFIG_OF_SEPARATE which will initialize the DT
from a board-specific funtion instead of bundling one with U-Boot or as
a separated file. This allows boards like the Raspberry Pi to reuse the
device tree passed from the bootcode.bin and start.elf firmware
files, including the run-time selected device tree overlays.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Adjust the video driver to work with driver model and move over existing
baords. There is no need to keep the old code.
We can also drop setting of CONFIG_FB_ADDR since driver model doesn't have
this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Start using driver model for USB on the Raspberry Pi. The dwc2 supports
this now so this is just a config change.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This is not needed now that serial uses driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Enable CONFIG_DM_ETH to make MACB to support driver model.
Because the USB Ether doesn't support driver model so far,
remove this feature.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Move existing configuration from header file to defconfig or dts as
appropriate.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This patch adds the option to configure a comphy to 5G XFI mode.
In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
phy2 {
phy-type = <PHY_TYPE_SFI>;
phy-speed = <PHY_SPEED_5_15625G>;
};
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE is different from UNCONNECTED since setting
UNCONNECTED type will disconnect the COMPHY in the COMPHY MUX
which is a desired behaviour
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add NAND configuration parameters to A8K shared config file.
Add defconfig for db-88f7040 board with boot from NAND setup.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
|
|
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.
The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.
The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.
So, the network driver would only need to enable these clocks, no need
to configure the rate.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is a simple uclass for Watchdog Timers. It has four operations:
start, restart, reset, stop. Drivers must implement start, restart and
stop operations, while implementing reset is optional: It's default
implementation expires watchdog timer in one clock tick.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
netboot allows to boot an external image using TFTP and NFS protocols
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
The IGEP SMARC AM335x is an industrial processor module with
following highlights:
o AM3352 TI processor (Up to AM3359)
o Cortex-A8 ARM CPU
o SMARC form factor module
o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
o WiFi a/b/g/n and Bluetooth v4.0 on-board
o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC BootROM whole
NAND is UBI managed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
|
|
This patch removes:
- CONFIG_CMD_MEM: enabled by default
- CONFIG_DESIGNWARE_ETH : not being used anywhere.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
USB bus scan attempt:
----------------------------------cut----------------------------------
=> usb start
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... data abort
pc : [<fff6240e>] lr : [<fff623b3>]
reloc pc : [<8081b40e>] lr : [<8081b3b3>]
sp : fdf42930 ip : fdf42960 fp : 00000000
r10: 00000001 r9 : fdf42ef0 r8 : 48890020
r7 : 00000002 r6 : fffa5840 r5 : fff8b140 r4 : fdf429c0
r3 : 00000000 r2 : 00000004 r1 : 00000000 r0 : 00000000
Flags: nZcv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
----------------------------------cut----------------------------------
Fix by enabling USB configuration in the SPL.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
The symbol CONFIG_DRA7XX is needed for Kconfig conditions.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
A feature rich Linux kernel needs more than 8 MiB.
Hence enlarge CONFIG_SYS_BOOTM_LEN to 64 MiB for the GXBB systems.
As all known GXBB systems have at least 512 MiB of RAM this poses no problem.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
0x10000000 is the start of a 2 MiB area used by the
ARM Trusted Firmware (BL31).
See
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/tree/arch/arm64/boot/dts/amlogic/meson-gx.dtsi?id=refs/tags/v4.10.10
So we should not load the ramdisk here.
The legacy Ubuntu image for the Odroid C2 comes with the
following line in boot.ini:
setenv initrd_loadaddr "0x13000000"
See
http://odroid.in/ubuntu_16.04lts/ubuntu64-16.04-minimal-odroid-c2-20160815.img.xz
http://deb.odroid.in/c2/pool/main/u/u-boot/u-boot_20170226-752a100-8_arm64.deb
So let's use the same address.
With the patch booting Linux with booti succeeds on an Odroid C2,
without the patch Linux hangs.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
|
|
To enable automatic booting from SD card or eMMC the MMC
devices 0, 1, and 2 are added to the BOOT_TARGET_DEVICES.
Booting from SD card, eMMC, and DHCP are tried in sequence.
A missing or failing device is gracefully handled.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
|
|
Signed-off-by: Chris Packham <judge.packham@gmail.com>
[trini: default y if DM_RTC, re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_CMD_DISPLAY
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_CMD_DIAG
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This option is not used in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
