summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2007-11-13Merge branch 'master' of git://www.denx.de/git/u-bootStefan Roese
2007-11-03Cleanup coding style; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-11-03Fix USB support issue for MPC8641HPCN board.Zhang Wei
The configuration file has already enabled USB, but it missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB on MPC8641HPCN can not work because of the wrong USB register endian. And add the USB command to U-Boot commands list. Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
2007-11-03Use config_cmd_default.h instead of config_cmd_all.hJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-03changes for IDS8247 board supportSergej Stepanov
To get the IDS8247 board working following are done: - FCC2 is deactivated - FCC1 is activated - I2C is activated - CFI driver is activated - Adapted for use with LIBFDT Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de> --
2007-11-02Merge branch 'master' of /home/wd/git/u-boot/workWolfgang Denk
2007-11-02Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2007-11-01ATSTK1002: Remove default ethernet addressesHaavard Skinnemoen
Wolfgang is right: It's not a good idea to set up default initial ethernet addresses for a board, even though they belong to the local range. This will change the failure mode from "IT manager screams at you for using duplicate ethernet addresses" to a nice error message explaining that the ethernet address hasn't been set properly. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-coldfireWolfgang Denk
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-tq-groupWolfgang Denk
2007-11-01Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-mipsWolfgang Denk
2007-11-01Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xxWolfgang Denk
2007-10-27Merge git://www.denx.de/git/u-bootStefan Roese
2007-10-25ColdFire 54455: Fix correct boot location for atmel and intelTsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2007-10-25ColdFire 5329: Assign correct SDRAM size and fix cacheTsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2007-10-25ColdFire 5253: Assign correct SDRAM sizeTsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2007-10-25ColdFire 5282: Fix external flash boot and return dramsizeTsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2007-10-25TQM5200: increase kernel_addr_r and fdt_addr_r (hinted by Wolfgang Denk).Bartlomiej Sieka
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2007-10-24Merge branch 'motionpro_ng' of /home/tur/git/u-bootWolfgang Denk
2007-10-24TQM5200: fix spurious characters on second serial interfaceMartin Krause
With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause <martin.krause@tqs.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-10-24TQM5200: fix spurious characters on second serial interfaceMartin Krause
With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-24Mips: Fix string functions differ prototype declarationJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-24delta: Fix OHCI_REGS_BASE undeclared and wait_ms implicit declarationJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-24xsengine: Fix no partition type specified, use DOS as defaultJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-24lubbock: Fix no partition type specified, use DOS as defaultJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-10-23fix pxa255_idp boardMarcel Ziswiler
The pxa255_idp being an old unmaintained board showed several issues: 1. CONFIG_INIT_CRITICAL was still defined. 2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined. 3. Symbol flash_addr was undeclared. 4. The boards lowlevel_init function was still called memsetup. 5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000. 6. Using -march=armv5 instead of -march=armv5te resulted in lots of 'target CPU does not support interworking' warnings on recent compilers. 7. The PXA's serial driver redefined FFUART, BTUART and STUART used as indexes rather than the register definitions from the pxa-regs header file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to avoid any ambiguities. 8. There were several redefinition warnings concerning ICMR, OSMR3, OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file. 9. The board configuration file was rather outdated. 10. The part header file defined the vendor, product and revision arrays as unsigned chars instead of just chars in the block_dev_desc_t structure. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2007-10-23Make MPC8266ADS command selection more robustRune Torgersen
Fix MPC8266 command line definition so it won't break when new commands are added to u-boot. Signed-off-by Rune Torgersen <runet@innovsys.com>
2007-10-23Motion-PRO: Update configuration to accomodate next generation board.Bartlomiej Sieka
New board has faster oscillator and a different Flash chip. This affects: - CFG_MPC5XXX_CLKIN - SDRAM timings - Flash CS configuration (timings) - Flash sector size, and thus MTD partition layout - malloc() arena size (due to bigger Flash sectors) - smaller memory test range (due to bigger malloc() arena) This patch also enables more extensive memory testing via "mtest". Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2007-10-23ppc4xx: lwmon5: Some further GPIO config changesStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-23Merge branch 'u-boot' of /home/mkr/git/u-boot-tq-group into bugfixMartin Krause
2007-10-21[MIPS] Fix UNCACHED_SDRAMVlad Lungu
PHYSADDR is for physical address, KSEG1ADDR is for uncached. Signed-off-by: Vlad Lungu <vlad@comsys.ro> Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
2007-10-21Merge branch 'master' of git://www.denx.de/git/u-boot-tq-groupWolfgang Denk
2007-10-21Merge branch 'master' of /home/git/u-boot/Wolfgang Denk
2007-10-19Improve handling of PCI interrupt device tree fixup on MPC85xx CDSKumar Gala
On the MPC85xx CDS we have two issues: 1. The device tree fixup code did not check to see if the property we are trying to update is actually found. Its possible that it would update random memory starting at 0. 2. Newer Linux kernel's have moved the location of the PCI nodes to be sibilings of the soc node and not children. The explicit PATH to the PCI node would not be found for these device trees. Add the ability to handle both paths. In the future we shouldn't handle such fixups by explicit path. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-19Set OF_STDOUT_PATH to match the default console on MPC8568 MDSKumar Gala
On the MPC8568 MDS we use ttyS0, UART0, etc. as the standard configured console. Make it so we match that config what we tell Linux as the early STDOUT console. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-10-16Make MPC8266ADS board compile again.runet@innovsys.com
Signed-off-by: Runet Torgersen <runet@innovsys.com>
2007-10-15ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & YosemiteStefan Roese
The BCSR status bit for the 66MHz PCI operation was correctly addressed (MSB/LSB problem). Now the correct currently setup PCI frequency is displayed upon bootup. This patch also fixes this problem on Rainier & Yellowstone, since these boards use the same souce code as Sequoia & Yosemite do. Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-15TQM860M: adjust for doubled flash sector size.Martin Krause
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with doubled sector size. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-15TQM866M: fix SDRAM refreshMartin Krause
At 133 MHz the current SDRAM refresh rate is too fast (measured 4 * 1.17 us). CFG_MAMR_PTA changes from 39 to 97. This result in a refresh rate of 4 * 7.8 us at the default clock 50 MHz. At 133 MHz the value will be then 4 * 2.9 us. This is a compromise until a new method is found to adjust the refresh rate. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-15TQM866M: adjust for doubled flash sector size.Martin Krause
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with doubled sector size. Signed-off-by: Martin Krause <martin.krause@tqs.de>
2007-10-14[FIX] XUPV2P change command handlingMichal Simek
and remove code violation
2007-10-13Merge branch 'master' of git://www.denx.de/git/u-boot-avr32Wolfgang Denk
2007-10-13Merge branch 'merge' of git://www.denx.de/git/u-boot-microblazeWolfgang Denk
2007-10-13Merge branch 'master' of git://www.denx.de/git/u-boot-nand-flashWolfgang Denk
2007-10-13Coding Style cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-10-13Merge branch 'master' of git://www.denx.de/git/u-boot-armWolfgang Denk
2007-10-12GP3 SSA: enable RTCWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-10-10Merge branch 'master' of /.automount/castor-vlab/root/home/wd/git/u-boot/master/Wolfgang Denk
2007-10-10Merge branch 'hellrosa_i2c' of /home/gjb/git/u-bootWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-28 01:34:27 +0000